Search Documents

By Steve O. Green

Introduction The US coal mining industry is in the midst of a serious economic crisis. To overcome increased operating costs, operators must take advantage of technological advancements in mining systems and equipment. A relatively new concept available to underground operators is that of extending the cutting depth for continuous mining machines (continuous miners). This system is referred to as deep-cut mining, and may be described as mining cuts to depths greater than the standard 6 m (20 ft). Productivity is increased through the reduction in continuous miner tram time since the machine stays longer in each working face. To successfully implement a deep-cut mining system, three problems must be overcome: Exposing personnel to unsupported roof, methane removal, and controlling respirable dust. Remote control cutting The solution to the unsupported roof problem is remote control. Recent advances in remote operation, especially in radio remote controls, have resulted in what is generally accepted as a safe and reliable tool. By installing remote control on the continuous miner, the operator and helper can now be stationed in a supported area. This allows for improved visibility while cutting coal. With this in mind, the limiting factor now becomes the position of the haulage equipment operator. North River No. 1 uses Joy 21SC shuttle cars and Jeffrey 4110 diesel ramcars. These cars are pulled against the bumper of the continuous miner. Thirteen meters (43 ft) can be cut with the shuttle car and 14 m (45 ft) with the Ramcar before the operator of the car is inby permanent supports. By loading away from the bumper, about 1.5 m (5 ft) can be added, bringing total cut depths up to 14.5 and 15 m (48 and 50 ft), respectively. Methane removal The second problem involves methane removal, and the line curtain-to-face distance. In other words, how to maintain the line curtain to allow sufficient ventilation to remove methane and not expose workers to unsupported roof. The solution, in most cases, is to use a blowing-type ventilation system. Unlike the exhausting system that, to be effective, must be installed within 3 m (10 ft) of the working face, the blowing system can be effective at greater distances from the face. Numerous studies have documented the advantages of a blowing-type ventilation system over an exhausting system. Furthermore, a blowing system can be significantly improved by in¬creasing the velocity of the air delivered without increasing the volume of air. With this greater ventilation efficiency, it is possible to secure ventilation plan approval from the Mine Safety and Health Administration (MSHA) for a greater curtain set-back distance. This eliminates the need for personnel to travel inby permanent supports to extend the face brattice. The distance from the face MSHA will approve, however, is on a mine-by-mine basis. MSHA will evaluate the particular mine's face methane liberation rates, along with the specific proposals regarding face ventilation volumes and velocities. Dust control The third problem is controlling respirable dust. This is actually a result of the solution to the second problem. In the blowing system, while mining on the slab cut, both the continuous miner and haulage units are located on the dusty side of the line curtain (Fig. 1). In the early 1970s, underground operators virtually abandoned this system, in order to comply with the 2 mg/m3 (0.87 gr per cu ft) federal dust standards. The blowing face curtain did offer increased face ventilation efficiency. With that, greater curtain-to-face distances were also

Jan 8, 1987

By Jon Kellar, Samuel Kessinger, Prasoon Diwakar

Tantalum (Ta) and niobium (Nb) are extracted from many different ore types. The major economic orebody mined for tantalum and niobium consists of tantalite ((FeMn)Ta2O5) and columbite ((FeMnNb2O5)) in a solid-solution mineral commonly referred to as “coltan.” The largest supplying region, The Democratic Republic of the Congo (DRC), is unfortunately also the most ethically compromised source for this critical mineral. Officially, the U.S. government has deemed coltan ore from the DRC a “conflict mineral” [1]. The lack of pragmatic and effective local mining regulation in Central Africa, when coupled with high levels of violence and corruption, has spawned a widespread, illegal, unethical and, most importantly, unsafe economy. This illicit economy is centered around first, illegally mining these valuable conflict minerals and second, smuggling these minerals into the global supply chain. Handheld spectroscopy devices could provide further transparency to these opaque supply chains, giving miners, traders and refiners the ability to authenticate the provenance of the minerals they encounter, and allowing companies to prove compliance with the regulatory agencies attempting to curtail illicit mining.

Mar 1, 2025

By Peter G. Chamberlain

Many mining engineers considering in-place leaching for the first time are uncertain as to how to evaluate ore bodies for potential leachability. Evidence presented in this report emphasizes the critical role of permeability in such evaluations. Whether an engineer is considering leaching "tight" formations typified by the porphyry copper deposits of the southwest or the permeable uraniferous sandstones of Texas and Wyoming, permeability measurements are the keystone of any testing program. Permeability tests range from cheap and easy to highly expensive and sophisticated operations. Constant head, variable head, and pumping tests all have application in evaluating ore bodies for in-place leaching. Costs of these tests will not unduly deflate the pocket- books of most mining companies. The basic procedures for selecting and running these field tests-including preparing suitable wells--are reviewed for the benefit of newcomers to in-place leaching.

Jan 1, 1979

By Jorge Rubio, Luis Valderrama, Carlos Pérez

This work describes the effect of the degree of energy transferred to the pulp, during the conditioning stage, on gold flotation fines recovery, grade and kinetics, with three types of frother (Dowfroth 250, pine oil and MIBC) and amyl xanthate as collector. Best results show an increase in 24% recovery and 50% in concentrate grade, depending on the intensity of conditioning and type of frother (better with Dowfroth 250). For low or intermediate energies (0.5-1.5 kWhlm3 pulp), the fine particles adhere to larger ones, increasing the recovery due to a mixture of carrier (pyrite, in this case) and autogeneous carrier flotation and at higher shear (2-3 kWhlm3 pulp), gold fine particles aggregate themselves. These phenomena are demonstrated by measurements of flotation rate, true flotation (flotation by actual particle-bubble adhesion), and by the amount of entrained particles. Alternatives for this type of pulp conditioning and mechanisms involved are discussed.

Jan 1, 1995

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By Donald Leroux

For the last few years, the grinding model first proposed by Andrews and Mika (1975) has regained attention from the scientific community. Though sophisticated identification algorithms have been developed, the number of its parameters that have to be estimated remains huge. Most of these constants (often more than 90%) are for the breakage function. This paper describes a new method for reducing efficiently the number of the breakage function parameters of the Andrews-Mika grinding model. It makes use of second-order statistics and of a stereostochastic model for liberation (for instance, BooKing).

Jan 1, 1992

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

By Merih Celasun

The literature in operations research centered on mineral exploration has been comparatively limited in view of the significant implications of mineral discoveries upon the national economies in general and mineral industries in particular. Much of what has been published is of somewhat unsure academic nature, indicating to a certain extent the scarcity of industrial applications. Mineral exploration activities present quite difficult operational and conceptual problems. The purpose of this paper is to discuss the principal characteristics of decision problems encountered in planning an exploration program, to indicate an optimization approach to a certain class of allocation problems, and to suggest directions for future research effort.

Jan 1, 1962

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By Edgar Urbaez

Production scheduling is one of the most important factors affecting mine planning. A program -Mine Scheduler -that aids mining engineers with the setup of an optimum open pit production scheduling algorithm has been developed. A mathematical model for open pit scheduling that optimizes the Net Present Value of the cash flows was formulated. A simulated data is formulated as a Mixed Integer Linear Programming (MILP) problem. What's Best by Lindo Systems is used as the MILP solver in Microsoft Excel. The implementation of the algorithm focuses on problem setup, allowing users to easily evaluate, simplify, and develop the model that best fits their production scheduling.

Jan 1, 1999

By Bryan Ulrich

On March 20, 2014, the ?Roundtable Discussion on Innovations in Heap Leaching and Mine Waste Management? was hosted by Knight Piésold and Co. at the Red Lion Hotel in Elko, NV. This topic is timely, and formed something of a lead into the inaugural ?Workshop on Innovations in Waste Rock, Tails and Heap Leach Management.? That workshop, which grew from the 2013 Elko Roundtable, was held on the University of Nevada, Reno (UNR) campus on May 19, 2014. The workshop was hosted by UNR and the University of British Columbia. Knight Piésold?s local representatives, Bryan Ulrich and Logan Jensen, were joined by Tom Kerr, president of Knight Piésold?s, U.S. practice; Rick Frechette, senior vice president, environmental services and Jeff Coffin, geotechnical engineer, from the Denver, CO office for the roundtable event. The event played host to about two dozen attendees from several western states.

By Charles E. Mauk

In 1970, recognizing the great need for an economical, high capacity chemical oxidation process for wastewater treatment, Houston Research began a fundamental study of the available technology, Included was waste characterization; oxidation chemistry for molecular oxygen, ozone and catalyst initiators; kinetics of reaction; gas-liquid contacting methods; and optimization of staged reactors for mixed wastes. Although ozone is the most powerful oxidizer available, the literature contains contradictory reports of its speed and effectiveness. It is now felt to be most likely that many of these early investigations were limited by the ineffectual transfer of ozone from the gas phase into the liquid, and so the investigators were really observing the effects of mass transfer and erroneously trying to interpret the results as if they were chemical reaction data. HR's work considered the cost and effectiveness of gas-liquid contacting in a packed tower, gas sparged contactor, ejector with hold-up tank, and a completely mixed, sparged contactor. The sparged, mixed contactor was found to be most effective and least expensive, and a later investigation settled on the reactor configuration shown in Figure 1 because of its effectiveness of mass transfer and because it lends itself to direct scale-up techniques using laboratory data to design larger reactors.

Jan 1, 1975

By J. D. Morgan

Demand for nonfuel minerals depends in large measure on economic activity, which rose in each quarter of 1985. However, despite 1.7 million new housing starts and a 7% increase in motor vehicle production, many domestic metal mining operations experienced continued difficulties as a result of import competition, greater use of newer engineered materials, emphasis on multi-unit housing, and downsizing of motor vehicles. Recognizing the continued difficulties of the domestic metal mining industry, many corporations made major efforts to retrench and rationalize - selling, closing, or spinning off less profitable operations, renegotiating labor contracts, and inviting increased participation by foreign firms. About 15% of US energy was imported in 1985. This included $52 billion worth of crude oil and refined products, adding significantly to the overall merchandise trade deficit of $149 billion. With the exception of a few large-bulk, low-value raw materials, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult US nonfuel minerals trade deficit totalled $17 billion. The US continued to rely on imports for many important strategic minerals in 1985 (see accompanying Table). Increased pressures for protection included major mineral products such as steel, ferroalloys, and copper. But President Reagan, in his Feb. 1986 "Economic Report to the Congress" stated: "Our international trade policy rests firmly on the foundation of free and open markets." He also stressed the need for fair trade and more open markets internationally. The National Critical Materials Council, created by law in the latter part of 1984, was activated in the latter part of 1985. Its first public hearing was held in January 1986. The Council is to review the nation's materials posture and advise the President on such matters. Compared with 1984, the value of US raw nonfuel mineral output rose 2%, to $24 billion. This supported the production of $244 billion worth of processed materials of mineral origin. Raw steel production - a major indicator of both material use and mineral production - fell 4% to 81 Mt (89 million st). Consequently, domestic iron ore production fell to 49 Mt (55 million st), about 97% pelletized. Iron ore imports fell 7% to 16 Mt (18 million st). Raw steelmaking capacity fell 4% to 117 Mt (129 million st). Pacts with 16 leading steel exporting nations have been negotiated in an effort to reduce import penetration of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 40% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production increased slightly to 49 kt (54,000 st). Mine shipments of tungsten, another mineral tied to steel production, also fell slightly to 1.1 kt (1200 st) of contained metal. Even the domestic aluminum smelting industry suffered reverses as high stocks and low prices reduced production 16% to 3.5 Mt (3.8 million st). Similarly, imports of bauxite fell 7% and alumina 10%. Production of magnesium metal fell 6% to 136 kt (150,000 st), while titanium metal production remained unchanged at 22 kt (24,000 st). Copper mine production was unchanged at 1.1 Mt (1.2 million st). Copper refinery production fell slightly to 1.1 Mt (1.2 million st). Lead mine production rose 24% to 400 kt (440,000 st). Zinc mine output was down 10%, to 225 kt (250,000 st). Refined lead production increased 28%, to 510 kt (560,000 st). Primary slab zinc production fell 5% to 240 kt (260,000 st).

Jan 5, 1986

By Edward J. Harvey

Joplin, one of the most famous zinc mining camps of a bygone era, is today experiencing a healthy growth in manufacturing enterprises. Manufacturing requires water, and knowledge of its availability and quality often is the main factor in location of industry. For this reason in January 1964, on the suggestion of the former State Geologist, Dr. Thomas R. Beveridge, a study of the water resources of the Joplin District was undertaken as a cooperative effort of the Missouri Geological Survey and Water Resources now under the direction of Dr. William C. Hayes and the U. S. Geological Survey. The project area is in southwestern Missouri on the Springfield Plateau and is bordered on the west and north by the Osage Plains of Kansas and Western Missouri, (fig. l). Upland altitudes rise from 900 feet above sea level in the west to 1400 feet in the east. The countryside is rolling to moderately hilly and much is excellent farmland.

Jan 1, 1965

By R. M. White

Abstract. Gulf Coast Salt Domes are being considered for radioactive waste disposal and this paper describes the geophysical techniques currently being used and those being considered for later phases of the program. Detailed gravity work utilizing a modification of the Talwani-Ewing modeling technique, shallow high resolution reflection seismic surveys using the mini-sosie concept, surface electrical resistivity and down-hole geophysical logging to add a third dimension to all of the surface techniques and to allow inverse modeling of the surface data sets are being utilized. The logic of the combined geophysical surveys will be discussed as well as their relative economics and their relationship to the overall exploration effort.

Jan 1, 1980

By W. Dan Hausel

Archean supracrustal rocks of the South Pass greenstone belt of western Wyoming have been an important source of gold and iron ore. Actual gold production statistics are incom- plete although gold production estimates for the South Pass- Atlantic City district range from a low of 2.0 Mg (70,000 oz) (Koschmann and Bergendal, 1968) to a high of 9.8 Mg (327,000 oz) (Hausel, 1980). From 1962 to 1983 iron ore was also mined from the greenstone belt and production totaled more than 91 Mt (90 million It). The supracrustal rocks of the South Pass greenstone belt occur in a tightly folded synform bounded by Late Archean granite and granodiorite. The youngest of the Archean successions has a reported Rb-Sr isochron age of 2.8 b.y. (Stuckess, et al., 1985). Metamorphism of the supracrustals increases towards the flanks of the belt and is amphibolite-grade enclosing a small island of greenschist facies rocks. The supracrustal sequence consists of metasedimentary and metaigneous rocks that are divisible into four mappable units. The metasediments include metagraywacke, quartzite, pelitic schist, banded iron formation, metaconglomerate, and graphitic schist. Metavolcanics include metabasalt, meta-andesite, and ultramafic schist. These supracrustals have been intruded by mafic sills and dikes and tonalitic stocks and dikes. Two granite plutons and associated pegmatites intrude the supracrustals in the western portion of the belt, and the supracrustals exhibit both fault and intrusive contacts with granitic batholiths along the western and eastern margins. The northeastern flank of the Archean belt is unconformably over- lain by Paleozoic sediments, and the southern portion of the belt is onlaped by Tertiary sediments.

Jan 1, 1990

By G. Danko

Ventilation and refrigeration for mine climate modification, contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can be used to minimize the impact of these costs. There are several computer codes available including CLIMSIM?, to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely: what accuracy is required of the basic input parameters, in order for a certain precision to be obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed to the changes of the rock thermo-physical properties, the heat transfer coefficient and the wetness factor.

Jan 1, 1988

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972

By G. H. Jardine

Mine planning and production scheduling in surface mines are basically iterative processes which are ideally suited to the use of computer-based techniques. Both processes are truly three-dimensional and lend themselves to the application of 3-D interactive graphics. Until recently, this has applied the need for the costly, dedicated graphics screens and mid range minicomputers. However, ongoing advances in processor chip design led to the emergence of inexpensive and powerful 5 to 10 Mips desktop work- stations. These workstations have the processing power to support rapid, high resolution, 3-dimensional graphics. By combining these workstations with powerful 3-D CAD software and, with a suite of comprehensive mine planning and scheduling applications, Mincom has developed a most cost effective solution to modern mine planning challenges.

Jan 1, 1989

By W. Wan

Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer and distribution of DPM in the mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Studied using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study will be presented.

Jan 1, 1994