Search Documents

By M. F. Dibble

Borehole mining, as a viable concept for recovering deep sedimentary mineral resources, historically has been long on promise but short on results. Application of the technology seems best suited for recovery of Miocene phosphate resources on the East Coast of the US. These deposits are potentially enormous in scope and underlie sections of the coastal plain and the near offshore continental shelf. The landside portion of these deposits is generally too deep to mine using conventional open pit methods. Recovery of these minerals requires development of alternative mining systems. A significant proportion of the offshore resources appear to occur at depths below the practical limits of cutter suction dredges and may even exceed the limits of bucket ladder dredges. In most cases, these deposits are covered by overburden that must he removed and redeposited before the mineral section can be mined. The depth, thickness, composition of overburden and environmental sensitivity of a particular location would greatly impact mining system selection. It is probable that dredging would not be an environmentally acceptable mining method in many of the areas underlain by this phosphate rock. In cases such as these, new processes such as borehole mining must be evolved or the resource will remain undeveloped. A borehole mining test program, using an existing prototype borehole system, successfully extracted Miocene phosphate in northeast Florida in 1984-1985. The top of the main mineral zone was 80 m (261 ft) below the surface. Based on the results of this test program. plus subsequent laboratory testing and engineering studies, a new prototype borehole mining system was designed in 1986. This design incorporated several innovations of offering potentially higher productivity and lower power consumption than was achieved with the previous test unit. Economic restraints at that tine prevented the actual construction and testing of this new design.

Jan 1, 1992

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By Robert M. Adler

In order for a taxpayer to produce income, he may be required to exhaust his capital assets. With respect to the mining industry, those exhaustible capital assets may result in income tax deductions under the general categories of depreciation, obsolescence, losses and depletion. The percentage depletion deduct ion concept is not based upon "economic" depletion, or "geological" depletion theories. Instead, it is wholly an income tax concept created by Congress. This is significant in that, in its application, tax depletion has no adherence to traditional economic or geological depletion concepts For example, the Internal Revenue Code limits percentage depletion to 50 percent of the miner's net income for the taxable period.1/ Should a particular miner extract and sell 500,000 tons of material during the year, but at a loss, he receives no percentage depletion. The same would apply to an electric utility which mined its own coal. Should its mining costs exceed the "going price" for coal, as established by actual arm's-length sales in the market, the utility has no net income, and is therefore not entitled to percentage depletion.2/

Jan 1, 1973

By R. L. Derick

The Orchard Valley Mine, a large underground coal mine located in western Colorado, experienced a major mine fire during an idled Sunday on June 1, 1986. This mine had extensive problems with spontaneous combustion near the coal outcrop. Spontaneous combustion has been determined to be the probable cause of that fire. Preparing for a mine emergency was an on-going task. Once the emergency occurred, much of the preparation work was implemented and aided in controlling the situation. Later, the successes and shortfalls that arose from that emergency were analyzed for future course of action. This paper summarizes the activity that led up to the major fire, the handling of that emergency, the lessons learned, and the changes implemented.

Jan 1, 1993

By Joseph Renk, David Akers, Glenn Shirey

Each year, US coal cleaning plants landfill or impound millions of tons of high-quality, fine-sized coal. This coal is not only difficult and expensive to capture during cleaning, but, if captured, can pose serious materials handling problems. The GranuFlow. Technology was developed and patented by the U.S. Department of Energy (DOE) to address these problems. GranuFlow involves the addition of a coal binding agent such as an asphalt or heavy oil emulsion to coal to reduce moisture, dusting, and freezing and to improve the flow properties of the coal in bins and chutes (1, 2, and 3). When the emulsion is added before mechanical dewatering, the binding agent causes the formation of fine-sized coal agglomerates that dewater better than untreated coal. In addition, the binding agent increases the capture of ultra-fine coal in screen-bowl centrifuges. Previous work by DOE has also demonstrated that such treatment results in a significant reduction in dustiness and a reduced potential to freeze. To address concerns about the handling and combustion characteristics of GranuFlow treated coal, DOE performed a pilot-scale pulverization and combustion test (4). No problems were encountered during pulverization or combustion, and use of this fuel in a p.c. boiler was found to be feasible from a technical perspective. CQ Inc. has an exclusive license from DOE to market this technology and is currently performing a series of commercial demonstrations to determine if GranuFlow is both technically and economically viable.

Jan 1, 2005

By Paul L. Russell

Introduction As the US and world population increases, so does the problem of supplying expanding energy needs. Early requirements worldwide were mostly met by abundant forest vegetation. Man's large scale use of minerals-energy resources is a fairly recent development. It occurred only during the past 200 years. Coal was the first mineral fuel to be used extensively. It was not a large factor in US energy production until the beginning of the 19th century. Petroleum and natural gas use is about 125-years-old. Electricity generation by falling water is about a century old. Atomic energy is only about 30-years-old. Extensive use of it is still in the future. Solar energy is in its infancy. Other energy sources such as wind, peat, and geothermal energy are minor and primarily of local importance. There were three main features of the fuel supply picture during the past 125 years. By 1900 coal replaced wood as the principal energy source. Since 1900, oil and gas have captured many coal markets. And after the mid-1970s, there was a resurgence of coal usage. (Figs. 1 and 2). Wood Until the advent of mineral fuels for energy, the major global energy source was wood. But populations increased and became centered in towns and cities. The problem of a sufficient energy supply first developed as nearby, easily obtained wood was exhausted. This problem became more acute as industries such as shipbuilding, smelting, and pottery making, became more widespread. Results of wood use as an energy source and building material are starkly evident in areas of the world where civilization is oldest. Entire forests were consumed and have never been replaced. In the US, wood supplied 90% of all fuel requirements until about 1850; and more than 50% until after 1880. By 1900, wood still supplied 20% of all energy uses. In the mid-1970s, energy costs increased, due largely to the oil embargo. This increase resulted in an increased wood demand for domestic heating. While large quantities of wood were being used, its share of the total energy market was still less than 3%. By 1983, wood was becoming increasingly scarce and more costly near most large US cities. Wind Wind powered ocean vessels for many centuries. Sailing ships were still common in 1900. Windmills provided an early, cheap energy source and continue to be used today on farms. Design and development of windmills for electricity generation is being conducted. Interest in wind power is growing worldwide where availability of wind currents warrants the investment. Also, US regulation requires power companies to "buy back" electricity generated by windpower in excess of that used by the windmill owner. Coal By the 1600s, England was producing, 900 kt/a (1 million stpy) of coal for heating and other uses. The first coal-fired blast furnace for iron smelting was developed in 1621. Coke-making was developed in 1755, and Watt invented the steam engine in 1769. Illuminating gas made from coal was introduced in London in 1800. During this same 200-year period, France and Germany developed coal production, but on a smaller scale than England. US, bituminous coal was mined near Richmond, VA, as early as 1748. Major bituminous coal-producing states in the early period were Pennsylvania, Virginia, Ohio, Kentucky, Illinois, and Maryland. West Virginia replaced Virginia as a major producer, when that state was formed in 1863. As the US expanded west, new coal deposits were found and exploited. Indiana, Alabama, Tennessee, Iowa, Kansas, Missouri, Washington, Colorado, Wyoming, Arkansas, Oklahoma (Indian Territory), Montana, New Mexico, and Texas had significant coal mining operations by 1900. Today the eight major coal producing states are Kentucky, West Virginia, Pennsylvania, Illinois, Ohio, Virginia, Wyoming, and Montana. These states accounted for about 80% of all coal (lignite, bituminous, and anthracite) produced in the US during the past several years.

Jan 8, 1984

By Thad J. Bydlon

Uncertainty of future energy supplies has forced industrial nations to diversify both their energy mix and their energy sources of supply. As a result, U.S. coal exports have grown substantially during the past several years. Projected long-term worldwide economic growth suggests that a well-established trend has been set for increased foreign demand for U.S. coal. As export volumes increase the need for careful planning to prevent bottlenecks and to provide for the uninterrupted flow of coal increases. It also will place increased emphasis on identifying the most economic transportation alternatives. These planning and evaluation functions are greatly facilitated if a systematic method is available for modeling the complex interactions of a coal export system. One such model, developed by the Anaconda Minerals Company, is the Coal Export model.

Jan 1, 1982

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, abetter means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas andwas called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32' Ø X 14' Long SAG Mill. The next was Island Copper in Port Hardy, B.C., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16'-6" Ø X 19' Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By Dan Mackie

Commissioning of a 150 tpd continuous vat leaching pilot plant at Ariel Resource's San Martin Mine began in October, 1995. Functioning of the systems proved to be as designed. Initial tri­als, however, were besieged with problems associated with clay fractions that were much higher than in the ore originally tested. Nevertheless, leach rates were good in the initial and subsequent trials. Difficulties with the viscous solutions generated by the clay fraction continued, requiring modifications to the solution collection methods and investigation of flocculant types and mixing points. Trials with deslimed ore and sand feed demon­strated continuous flow. Current modifications will be tried in late May, 1996, along with selected flocculants, with the objec­tive of leaching continuously without the need to deslime.

Jan 1, 1996

By Michael H. Leon, John A. Organiscak

Controlling worker dust exposure on longwall mining systems is difficult because the working face area serves as an immediate return during the mining cycle and the amount of airborne dust generated is directly related to production. Since improvements in longwall mining technology have significantly boosted production levels, additional technology is needed to control the airborne respirable dust generated at present and future production levels. One concept to reduce longwall worker's dust exposure is to maintain two splits of air at the face -- a clean intake split in the workers walkway, and a return (dusty) split over the face conveyor. The U. S. Bureau of Mines has recently investigated a concept to overcome the visibility handicap of face partitions by utilizing a permeable polyester mesh. The mesh material was anticipated to provide adequate air-splitting capabilities as long as the pressure differential between the face and worker walkway was minimal. Initial testing of this concept at the Bureau's Lake Lynn Laboratory showed that notable reductions could be achieved with a 1/8 in (3.18 mm) and 1/16 in (1.59 mm) mesh opening size. Dust reductions at 100 ft (30.5 m) and 200 ft (61.0 m) downstream of source were 58 and 36 pct, respectively, for the 1/8 in mesh and 79 and 55 pct, respectively for the 1/16 in mesh. Longwall application of the 1/8 in mesh showed similar results to the Lake Lynn Laboratory tests. A flame retardant mesh was used underground with portable lighting mounted on the shearing machine for face side lighting.

Jan 1, 1993

By J. E. Lawver, F. S. Knoll

Introduction Electrostatic separation is the selective sorting of solid species by means of utilizing forces acting on charged or polarized bodies under the influence of an electric field. Electrostatic separation is effected by adjusting those forces acting on particles due to the electric field as well as co-acting forces such as gravity or centrifugal forces so that the different species will have different trajectories at some predetermined time. Electrostatic separations can be broadly defined as being either electrophoretic or dielectrophoretic. Electrophoresis is the separation of charged particles in an electric field, whereas dielectrophoresis is the separation of neutral particles in an electric field1. Examples of an electrophoretic separation can be found with sepa¬rations that use corona charging (ion bombardment), contact charging (triboelectric) and conductive induction. Dielectrophoresis motions are due to the stress and repositioning of charges, i.e. polarization of a neutral particle when exposed to a non-uniform electric field. Separations made using corona discharge devices are often called high-tension, electrodynamic or ion bombardment separations. These are the most prevalent in use today in mineral processing. Dielectrophoretic separation of most minerals is based on differences in dielectric constants of the solid species and usually requires the use of expensive intermediate dielectric fluids. Dielectrophoresis has not been employed for industrial mineral separations, though its effects pose interesting possibilities1, and pilot-plant units developed by the U.S.B.M. are available for testing2. Our discussion will be limited to the three forms of electrophoresis found in commercial practice. Typical Industrial Separations Typical industrial applications of electrostatic separation are: 1. Dry concentration of heavy minerals: ilmenite, rutile, zircon, monazite, xenotime, columbite-tantalite, cassiterite, hematite, scheelite and others. 2. Separation of salts: halite-sylvite, etc. 3. Purifications of foodstuffs such as the removal of impurities and

Jan 1, 1986

By J. Cooper, M. W. Staub

Environmental management systems (EMSs) have been in use for more than a decade. US mining companies are only just beginning to adopt EMSs. This lag is primarily due to lack of market forces and lack of evidence that EMSs add value over standard compliance programs. Several recent studies concluded EMSs improve environmental performance and reduce costs. State and federal regulatory agencies are using EMSs as an innovative tool to streamline the regulatory process and achieve continual environmental improvements. The climate is right for the mining industry to adopt an EMS model that improves environmental performance and takes advantage of new regulatory programs.

Jan 1, 2004

By W. J. Kogelmann

Roadheaders, also called Boom Miners or Boom-type Tunneling Machines have been in North America since 1968, when first introduced by Willy Kogelmann, the founder of Alpine Equipment Corp. (?Alpine?). Roadheaders were invented in Europe in the late 1940s. Machines with in-line, axial cutter heads were developed in the former Soviet Union. The British Dosco DRCL is based on the Russian PK-3 roadheader. Roadheaders with transverse ?ripper? cutter heads were invented in Hungary (1). The Austrian-made Alpine Miners of VOEST-Alpine, purchased by Sandvik AB, are based on a 1965 Hungarian license. Roadheaders are widely used in the mining and tunneling industries because they can excavate drifts, entries and tunnels with cross sections of any shape and size, can handle mixed faces, work on steep grades, and negotiate tight curves and cross-cuts. A roadheader?s only major limitation is the strength and abrasiveness of rock and minerals to be excavated. This paper covers roadheader selection criteria, improvements in reliability, attachments for flexibility (Multi-Tool Miner), and automated support systems for increased cutting time for increased shift production.

Jan 1, 2008

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By Adrianus Halim, Jenni Hooli, Bartłomiej Skawina, Fredrik Sundqvist

Transitioning from diesel-powered loading and hauling machinery to battery-electric vehicles (BEVs) responds to the need for deepening underground mines as regulations become tighter. When using BEVs, exhaust gases and diesel particulate matter (DPM) emissions can be eliminated, and the energy required for the machines is used more effectively. Unlike their diesel counterparts, which are refueled, BEV loading and hauling machines — specifically, load haul dump (LHD) machines — can use battery swapping. This brings additional aspects to the operation that need to be considered, which have not yet been studied extensively. This study used discrete event simulation (DES) to analyze how the different numbers of BEV LHDs affect queueing and productivity when using different numbers of batteries and different swapping times in an underground block cave mine. The results identified the formation of working groups, where the machines swapped their batteries concurrently within each group, and their relation to the queueing time. Additionally, the minimum number of batteries per machine was identified to maximize productivity while minimizing queueing time. This study demonstrates DES as a powerful tool to assess and analyze conceptual systems and identify their underlying structures, which can enhance the deployment of BEV LHDs in underground block cave mine operations.

Apr 1, 2025