Search Documents

By Shusen Cheng, Dongdong Zhou

The high temperature distribution in ironmaking and steelmaking industry is very important to control the smelting process. Although equipment is available to measure the temperature in the smelting process, in general it could just measure one certain point or only at discrete times. The real time temperature distribution in ironmaking and steelmaking is important because it could reflect reaction information and help to control the operation parameters. In this paper, a new method to detect the temperature distribution in ironmaking and steelmaking through the application of digital imaging system based on the color CCD was studied. In addition, the two-color method and partial least square method were used in the calculation model to improve the accuracy. The results agreed well with the measured temperature.

Mar 1, 2017

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Anupam Madhukar

The essence of an atomistic unified kinetic model of strained thin film growth and defect initiation is presented along with a comparison of its consequences obtained from computer simulations with experiments. Within the competing kinetics of a strain dependent activated incorporation of atoms and an asymmetry between upwards and downwards inter-layer migration, the model provides a consistent description of 2D versus 3D morphology evolution accompanied by the appearance of surface vacancies and steps at no energy cost. The correlated migration of these precursor defects offers an atomistic mechanism for the emergence of surface half-loops from the growth front (thus accounting for configurational and thermal entropy) governed by activation energies closer to their correlated motion under the evolving strain fields and thus substantially less than those calculated with respect to the perfect crystal as the reference state. The essential mechano-chemical nature of the problem is compared and contrasted with the historical literature of such phenomenon as precipitation hardening and sintering in metallic and ceramic composites.

Jan 1, 1994

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Ramona Prillhofer

Salt slag is a waste product produced by the recycling of aluminum. In most European countries (e.g. Austria, Germany) the landfill disposal of this waste is forbidden because the slag contains soluble salts and these represent a potential source of pollution to the surface and groundwater. Additionally, consisting metal and some compounds in the salt slag can react with water and resulting from this, noxious gases are generated. The recovery of useful materials from these wastes is accordingly both environmentally necessary and economically feasible. This study describes a complete recycling-process for the salt slag, which includes a leaching-cristallization-process to obtain the oxidic residue, a pyrometallurgical-step to clear the oxidic residue and finally an extensive characterization of the achieved products. Due to the increasing price of raw materials, the utilization of the oxidic residue into commercial products has been investigated and application possibilities will be discussed.

Jan 1, 2009

By Bob Hannah, Peter C. Hayes

The changes that are happening in the world of metallurgy, and with it university education, are generational and require generational responses. Some of the key issues facing metallurgical education and ongoing professional training are explored. What will be required of metallurgical engineering professionals in the coming decades? What knowledge and skills will be needed? How to provide the educational and learning pathways, and how to attract smart young people into this profession? These are issues more readily addressed by tertiary institutions in conjunction with industry; perhaps the greater challenges lie in building and maintaining competencies post-graduation. There is a need to establish and maintain a system that supports graduates and enables them to develop further into competent expert engineers able to successfully address complex engineering challenges.

Jan 1, 2014

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By Vince Newberry

Alcan Rolled Products at Oswego, New York, commissioned Recycle II during May of 1995. Recycle II is an advanced technology UBC recycling facility designed to meet the most stringent environmental standards enforced to date in the United States, particularly with respect to NO, and particulate emissions. This paper addresses the exacting requirements and strategies of Alcan's Recycle II project andThorpe Technologies' design considerations and solutions for the supply of environmentally favorable melting furnace and delacquering systems. The furnaces are equipped with low NOx regenerative burners and furnace pressure and hearth gas flow controls designed specifically for processing the hearth gases through baghouses. The delacquering system is a new generation Apros concurrent flow unit designed for low NOx emissions.

Jan 1, 1995

By Christoph Beckermann, Kai Liu, Richard A. Hardin

"A two-dimensional heat transfer model for transient simulation and control of a continuous steel slab caster is described. Slab thermal and solidification conditions are computed by the model as a function of time-varying casting speed, secondary spray cooling water flow rates and temperature, slab thickness, steel chemistry, and pouring and ambient temperatures. A solidification model that includes the effects of steel chemistry, cooling rate and mierosegregation on the solidification path is incorporated directly into the caster model. Comparisons between measured and predicted liquidus and solidus temperatures are given for two low alloy steels, and show good agreement. Predicted and measured slab surface temperatures recorded on an operating caster are compared with this transient model and show that the model can predict the temperature response at the slab surface. Results of several simulations are given to demonstrate the effects of changing casting conditions on the slab thermal profile and the solidification end-point. A control methodology suitable for online control of a continuous casting machine is described, and its ability to control the surface temperature profile by dynamically adjusting secondary spray cooling flow rates is demonstrated using the simulator. IntroductionIn order to remain competitive in today's world-wide market for continuously cast steel products, steel producers are finding that it is ever more important to implement process control and to develop a more thorough technological understanding of their casting process. By integrating process control and monitoring into both production and quality control, producers are better able to meet customers' demands for steel of the required quality, quantity, size, grade, and properties at the lowest cost. Computer models used for real-time/on-line prediction and control of continuous steel casters are fundamental tools to accomplish this. Accurate on-line prediction and control of steel solidification and heat transfer allows for more flexibility in caster operation by giving operators the ability to change casting speeds while keeping critical process parameters within required ranges. Such control 'capability also results in more uniform quality throughout an entire casting sequence from startup to shutdown. Furthermore, due to the unreliability of temperature sensors, and the lack of good sensors for important process parameters such as solidification end-point and liquid pool depth, computer-based control models are often the only available option."

Jan 1, 2000

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By D. Gu, R. G. Anthony, C. V. Philip, M. E. Huckman

"In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the column, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux. We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nemst-Planck equation as the constitutive equation for diffusive flux. We use a NemstPlanck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model. The data from this comparison suggests that the Nemst-Planck type model yields better results.IntroductionMillions of gallons of strongly basic, radioactive waste are currently stored in underground storage tanks at Hanford and Savannah River and several locations within the United States. Due to the limited life expectancy of the tanks, there is a pressing need to remediate these wastes. This need has prompted the recent development of new ion-exchange materials for removing radioactive elements from aqueous solutions. A novel material called TAM-5 has been developed jointly by Texas A&M University and Sandia National Laboratories. TAM- 5, a crystalline silico-titanate, is highly selective for Cs + in the complex electrolytic solutions typical of these wastes. It is stable in very basic solutions and in radioactive environments [1, 2 ,3]. In laboratory testing to determine the selectivity of various materials, TAM-5 was superior to other candidate ion exchangers [4, 5]. The selectivities were determined by measuring a distribution coefficient, Kd, which is defined as the concentration, gig or mmols/g of Cs in the solid phase divided by the concentration, mg/L or mmols/mL, of Cs in the liquid phase. The units of Kd are ml/g or L/kg. Table 1 shows Kd values for TAM-5 compared to 9 other candidate materials in a typical waste solution [6]."

Jan 1, 1996

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By F. A. Myzenkov

The technology developed by the authors uses new methods for raw material smelting in electric furnaces, a new autogenous method and apparatus for subliming smelting for antimony trioxide production and separation of antimony and gold. Concentrate produced from the ore deposits in Yakutia has the following average contents of main constituents, % by weight: 29.4 Sb, 1.2 Fe, 13.1 S, 40.0 SiO2, 0.2 As, 2.6 CaO and 45 g/t of Au. Unlike the technology used abroad a new autogenous method makes it possible to increase considerably specific capacity and reduce gold losses with antimony trioxide by several times. At the same time mineralogical composition of trioxide has improved considerably ? it has mainly a cubic base with prevalence of senarmontite. The content of a main component (Sb2O3) in the final product has increased from 99.0% up to 99.6% which means better quality and makes it suitable for use in special technologies. Despite a lower antimony content of the concentrate (29.4% as compared with over 33% as common in the world practice), an antimony recovery of 85.3% into a commercial-grade product has been achieved, as well as a gold recovery of 96.65% into a gold-antimony alloy. The technology for processing gold-antimony materials developed and introduced at the Ryaztsvetmet plant is unique in the world with respect to gold recoveries.

Jan 1, 2006

By Malti Goel

"The cost-effective capture of carbon dioxide (CO2) from the point sources for its reduction the atmosphere offers many challenges in materials science. Novel CO2 capturing approaches using chemical, physical and biological methods are in the research stage and are aimed to minimize the cost. Appropriate materials development , which can withstand required temperature or pressure as the case may be for CO2 emanating from coal gas or industrial waste gases form the minimum condition. Other requirements are reclyclability of material and cost of separation. Nano-material composites can be more effective in selective capture of CO2 and can offer solutions for large-scale separation process. Nano-porous material catalysis can enhance the reaction rate of CO2 with other chemicals and thus help in capture of CO2 and convert it into value added products. This paper reviews recent industrial scale developments. In the Indian context, R&D priority areas in CO2 capture process development with a focus on energy industry are presented.IntroductionScience of Climate Change is growing at an enormous pace. With the ultimate goal of stabilization of greenhouse gases in the atmosphere, new scientific approaches are being researched worldwide. A shift in policies from low carbon and no carbon energy sources to fossil fuel sources with capture of carbon and its permanent storage is taking place. The process of carbon capture is both energy and materials intensive and the cost of power generation may increase up to 40% when carbon capture and storage (CCS) technology is implemented. Development of cost effective R&D technology therefore remains the greatest challenge before the scientific community."

Jan 1, 2009

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Weizhi Zeng, Michael L. Free, Shijie Wang

Copper electrorefining is an old technique that is generally performed in electrolytic cells with a bottom inlet and top outlet that are convenient for electrolyte flow control. Nevertheless, this configuration cannot effectively direct electrolyte flow to the regions between electrodes, which results in weak convection and inadequate delivery of chemical species and additives. In this article, we discuss the innovations in electrore fining cell design to improve electrolyte flow for better cathode quality and simulation of fluid flow field and particle movements based on finite element modeling method. The resulting fluid flows in cells can transport suspended slime particles to the cathode, where they can be incorporated as impurities. The concentration of suspended slime particles is inversely related to slime adhesion, which is strongly influenced by slime particle sintering, and sintering is dependent on temperature and slime particle composition. Thus, the combination of innovative fluid flow and slime particle sintering can play important roles in improving cathode quality.

Mar 1, 2017

By H. Y. Sohn

The considerable progress made in the sulfide smelting technology since the first International Sulfide Symposium of 1983 is discussed. The new developments and innovations have largely been driven by the recognition of environmental concern as well as the need for increased productivity. The smelting technologies for various nonferrous metals are reviewed, with an emphasis on the industry trend towards larger plants and continuous processes. The tremendous advances made in process modeling and computer simulation to describe the complex smelting processes are also reviewed. The goal of these mathematical models is the quantitative description of the processes and the reactors that will provide a means for the control and optimization of smelting operations as well as the optimal design of the operating conditions and the reactors. Environmental issues remain a key consideration in the smelting industry. One of the most remarkable improvements made in the last fifteen years since the 1983 Sulfide Smelting Symposium is the rapid increase in the sulfur capture by nonferrous smelters. This and other related issues are briefly discussed. Finally, the challenges that the smelting industry faces as the new millenium approaches are discussed. The industry continues to face technical challenges to improve productivity and efficiency, while being responsive to ever-increasing public pressure for environmental protection. It also faces external challenges from factors that may cause the reduction of metal uses as a result of substitutions by other materials. Another serious challenge and dire consequence that the primary metals industry is expected to face is the serious diminution of university-educated manpower as well as basic-research output. To remain competitive and healthy, the industry should take up the void left by the complete disappearance, at least in the U.S., and the reduction in other nations, of the governmental support of higher education and basic research in the field of primary metals production.

Jan 1, 1998

By Heikki Jalkanen

The mineralogical composition and morphology of solidified copper smelting and converting slags are of some interest from slag cleaning (by froth flotation), impurity elimination, and environmental points of view. Properties result from both the state of molten slag before solidification and processes taking place during solidification and cooling. In solidification and cooling, copper and sulfur dissolved in molten slag are .precipitating substantially from the silicate phase. Even in water quenching of slag, dissolved copper is pushed out of the solution in the form of finely divided precipitate. Elements present in the raw materials are distributed in a distinct manner between the solidified slag and non-silicate solidification products. Arsenic, antimony, and tin are strongly accumulated in copper precipitate, but not the other metallic constituents common in copper concentrates. Smelting and converting slags differ remarkably on their mineralogical composition and morphology although resulting principally of same chemical processes. Converter slags are more inhomogenous; they often contain solid particles and copper content is .as a rule higher than in matte smelting slags. The final copper content of converter slags was observed to be in a distinct manner dependent on iron oxide - silica ratio. Slag forming, solidification, and precipitation phenomena are discussed on the basis of mineralogical and morphology analysis of smelter slags and laboratory scale experiments.

Jan 1, 2002