Search Documents

By Batric Pesic

Recovery of gold from refractory ores was studied by pressure oxidation as the method of ore pretreatment followed by bromination of oxidized residues. Three different ores were examined, Au-Ag, Au-Ag-Te, and Au-silver free ore. Pyrite was the major host mineral for gold in these ores. The effect of pressure oxidation parameters (temperature, pressure of oxygen, time, and pulp density) on subsequent bromination under standard conditions was examined. Bromination of residues produced under standard pressure oxidation conditions was examined as a function of: temperature, bromine and sodium bromide concentration, and time. Recovery of gold on activated carbon, from the pulp after bromination, was studied too. Recovery of gold from silver containing ores was lower (87-91%) than the recovery of gold from silver free gold ore (97%). In each studied case, the presence of activated carbon in the pulp further increased the recovery of gold.

Jan 1, 1992

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Jun Enriquez

Kennecott Utah Copper aims to extend anode furnace campaigns to more than three years. As part of that goal improvements are sought on anode-furnace tuyere-area refractory performance. Kennecott and Praxair developed high pressure nitrogen refining for the Oxidation Stage which shortened anode furnace fire refining cycles by up to two hours per cycle. Future developments include optimizing the Reduction Stage’s steam-gas reforming and achieving coherent jet tuyereless refining.

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the fum ace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By R. Luo, R. V. Kumar

"The co-deposition of cobalt and nickel as a binary alloy has been studied by both cyclic voltammetry and long-period controlled-potential electrolysis. Cyclic voltammetry experiments showed that the cathodic current density for the mixed Co-Ni (Co-Ni=1:3) electrolyte is noticeably higher than that obtained on electrolyte containing single CO2+ or Ni2+ (II) salt of the same ionic strength. The onset potential observed for the mixed salts electrolyte was also less cathodic (negative) than that for the single metal salts, respectively. The effects of a number of operational and compositional parameters on the co-deposition of cobalt and nickel were studied. The parameters under investigation include cathode (deposition) potential, temperature, CI-/Sol ratio in the electrolyte, the amount of additives such as H3B03, and acidity of the electrolyte.Optimum operational conditions were established for the deposition of cobalt and nickel binary alloy. These results are discussed with respect to feasibility of reclaiming cobalt, nickel and chromium from mixed superalloy scraps by melt-refining (under nitrogen and/or ammonia), followed by electrorerining of cast anode for co-depositing Co/Ni and thermal decomposition of chromium nitride for recovering chromium metal."

Jan 1, 1997

By Eren Hüseyin Obuz

In this study, the leaching kinetics of rare-earth elements were investigated using HCl and HNO3 solutions. A standard crushed complex ore was utilized as raw material. The complex ore (particle size of under 54 μm) contains REE (Ce, La, Nd, Pr, etc.). Different leaching durations were selected for the kinetic studies. The highest leaching efficiency was obtained in HCl solution, and the leaching mechanism was identified to diffusion through a product layer. The rate constants of Ce, La, Nd, and Pr were calculated as 1.08 × 10−2, 0.86 × 10−2, 1.87 × 10−2, and 1.34 × 10−2 h−1, respectively.

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By G. D. Sandrock

The science and technology of roan temperature rechargeable metal hydrides began about 1969 with the discoveries that the intermetallic Compounds LaNi5 and TiFe could be, conveniently hydrided and dehydrided at roan temperature and modest H2 pressures. Subsequently, this lead to the development of a broad family of REE-containing AB5 hydrides and numerous applications that make use of the extraordinary H2-absorption and reaction-heat properties of these materials. Some of the applications include H2 storage, compression and separation, as well as heat pumping, heat to mechanical energy conversion and electric energy storage. This paper briefly reviews the fundamental phenomenology of metal hydrides, the history of the use of REE's in rechargeable metal hydrides, the practical engineering properties of these materials and the applications that have evolved around them. The rechargeable nickel metal hydride battery, a new vial alternative to NiCd cells, stands at the forefront of the applications.

Jan 1, 1992

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015

By R. W. Harnmack

Hydrogen sulfide generated by the anaerobic respiration of sulfate-reducing bacteria was used to treat pH 2.2 water from the abandoned Rio Tinto copper mine in Nevada. The untreated water contained 550 mg/L Fe, 140 mg/L Al, 90 mg/L Cu, 80 mg/L Mn, 60 mg/L Zn, 4 mg/L Co, and 2 mg/L Ni. The bench-scale treatment system examined consisted of a bioreactor for H2S generation and three precipitator/clarifier units for metal sulfide precipitation and recovery. The treatment system reduced the concentrations of all metals except Mn to less than 0.1 mg/L. Manganese concentrations were reduced by 96 percent to 3.3 mg/L. A CUS/SO concentrate (33 pct Cu) and a ZnS/5° concentrate (28 pct Zn) were produced that may be suitable for metal recovery at existing smelters

Jan 1, 1994

By P. Myllykoski, J. Nylander, A. S. Korhonen, J. Larkiola

The coefficient of friction and the deformation resistance have been determined from the measured rolling parameters by applying the Bland-Ford-Ellis rolling force model and the artificial neural network model (ANN). The dependence of friction on the parameters such as reduction, rolling speed, front and back tensions, contact pressure and deformation resistance have been studied by the ANN model. Measured data of over 10 000 coils have been used in the training stage. Various dependencies have been examined and the results show that the friction coefficient does not depend much on the rolling speed. The reduction and deformation resistance seem to have the strongest effect on the friction coefficient. A friction model based on neural computing has been included into the existing rolling force model.

Jan 1, 1994