Search Documents

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester, Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e., in flash combustion mode. The velocity, temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data, this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By Igor Rojkovic

The most important uranium mineralization in the Western Carpathians occurs in the Permian rocks. Low grade stratiform uranium mineralization was formed during the Permian due to adsorbtion and reduction by organic matter, titanium oxides, iron hydroxides, pyrite and clay minerals. During the Alpine orogeny uranium (± molybdenum and copper) remobilized stratabound ores were formed. Dominant ore minerals are uraninite, U-Ti oxides, molybdenite, pyrite and chalcopyrite Two generations of ore minerals are reflected by their textures and chemical composition.

Jan 1, 1995

By Francis Vanbellen

In Union Minière&apos;s Hoboken smelter and refinery for complex non-ferrous materials, the treatment of recycling products, containing precious metals, occupies a dominant place. For all feed materials, the first step, prior to their treatment, is to classify them in order toselect an accurate and economical procedure for sampling as well as to dispatch them to the optimal process scheme. More than 150 different procedures for sampling are commonly used. The most important ones are briefly discussed in the paper. Precious metals bearing recycling materials vary widely with respect to their physical aspect, their chemical composition and the value of their precious metal content. All these parameters are taken into consideration to select the most appropriate process among the multiple possibilities of Union Minière&apos;s flexible integrated flow-sheet. Different stages of the operations as well as the main flow-sheets are described.

Jan 1, 1995

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014

By Shengli Wu, Juan Zhu, Wei Huang, Xinliang Liu, Kaiping Du, Kaifa Zhang

Based on the furnace burden of high content of Al2O3, the process of softening and melting and the characteristic of primary slag were studied with the increase of MgO content in the sinter and adding some MgO into the pellet. The results showed that the content of MgO in the primary slag increased with the increase of MgO in the sinter and pellet. Meanwhile, the permeability of the furnace burden was improved because of low viscosity of high MgO primary slag. Compared with the increase of MgO content in the sinter, the increase of MgO content in the pellet can improved the softening and melting characteristic of the comprehensive furnace burden more effectively. More Mg-bearing pellet should be chosen in the comprehensive furnace burden for the purpose of improvement the fluidity of primary slag and the permeability of the furnace burden in the burden of high Al2O3 content.

Jan 1, 2015

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By Karl-Heinz Daum

Outokumpu Lurgi Metallurgie GmbH, Oberursel, Germany ? give saleable by-products, ? not interfere with smelter performance, ? treat all gas streams simultaneously, and ? comply with environmental regulations. The latest developments in sulphuric acid plant design are presented.

Jan 1, 2002

Physical and chemical methods were investigated to tower thorium levels in Eneabba Ilmenite from the natural levels of 180-500 ppm to give Becher Process synthetic rutile with less than 100 ppm thorium. Chemlcal treatments, but not physical separations were successful. A pilot plant trial of a sodium hydroxide leach (25M NaOH at 75°C and 40 wt% solids for Ih) followed by a sulphuric acid leach (3M H2S04 at 90°C and 60 wt% solids for 211) confirmed that thorium could be removed to below 100 ppm. However, the activity of the ilmenite was not lowered to the same extent

Jan 1, 1996

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Crystal precipitation behavior of calcium ferrite (CF) during iron ore sintering process along with the effect of cooling rate, SiO2 and Al2O3 on crystalline condensation were studied. The results show that CF, has strong ability of precipitation. The precipitation is barely affected by extenal factors. It begins to precipitate when the liquid phase cools down to about 1200oC. CF could crystallize rapidly at the cooling speed of 150 °C /min. Furthermore, decreasing of the cooling rate favors the development of crystal. Binder phase transformed from CF system to silicate system when SiO2 content was increased to 5~6%, with a constant basicity (R) 2.0. Increasing Al2O3 content could promote the precipitation of CF and the development of crystal.IntroductionCrystalline condensation is the last stage of sinter mineralization. It includes the processes that crystalline substance and amorphous substance precipitate from high temperature solution phase and the consolidation of material when melt cools down. During the crystallization process, minerals precipitate following the order from high to low melting point coupled with the decreases of free energy. Most of binder phase minerals and part of iron oxides crystallize in this process, which have an important influence on mineral composition and microstructure of sinter. They finally determine the sinter strength and metallurgical properties."

Jan 1, 2011

Thallium is a very minor element found in lead ores. It&apos;s behaviour during lead smelting has recently become of much greater interest due to the effects it had on the health of waste heat boiler maintenance contractors at a Canadian smelter. In this paper the behaviour of thallium in both traditional and direct lead smelting processes will be examined using computational thermodynamics techniques. Yazawa and his coworkers have made extensive use of computational thermodynamics to examine and illustrate pyrometallurgical processes. It has been shown that thallium behaviour during smelting is strongly influenced by the extent of oxidation of the lead concentrate and by the presence or absence of chlorine in the charge. The condensation behaviour of thallium species in the waste gas handling system was also modelled and it has been confirmed thallium-rich deposits can form at the high temperatures prevailing in waste heat boilers.

Jan 1, 2003

By Akira Kaneda, Nozomu Hasegawa

"In the Mitsubishi Continuous Copper Smelting and Converting Process, slag/matte mixture overflowed from the smelting furnace is separated continuously in an electric furnace (slag cleaning furnace, CL-furnace). In order to improve the separation efficiency of slag and matte and to minimize power consumption, the design and the operating conditions of the CL-fumace should be optimized. In the previous study, the authors developed a mathematical model for simulating phenomena in the CL-furnace. The model consisted of 3 modules, electric field analysis, heat and fluid flow analysis and the particle tracking method. In this study, the model was partially modified: k -E. model was adopted, and the effects of various conditions, such as furnace shape (including accretion) and scale, electrodes configuration, immersion depth of electrodes, and thickness of slag layer, were evaluated. And the optimum design and operating conditions were discussed.IntroductionUnder the recent environmental restriction, advantageous features of the Mitsubishi process have attracted much attention. The process uses 3 furnaces connected by launders. Mixture of matte and slag formed in a smelting furnace flows continuously to a slag cleaning furnace (CL-furnace), where the matte is separated from the slag. The matte is continuously siphoned out to a converting furnace and converted to blister copper. The slag overflowed from the CL-furnace is discarded. Because the slag contains about 0.6 % copper, improving slag/matte separation efficiency and decreasing copper loss make a great profit. Moreover the process requires a large amount of electric energy, so reduction of electric power consumption brings in enormous benefit.The objective of this study is to optimize the design and the operating conditions of the process, especially the CL-furnace. This will be achieved by developing the mathematical model and clarifying relations between the design or the operating conditions and various phenomena in the furnace. Fig. 1 shows an outline of the CL-furnace. The mixture entering through an inlet is separated to slag layer and matte layer . In order to maintain the temperature of the melt at a predetermined level, 6 electrodes are immersed into the lag and Joule's heat is generated by 3-phase alternating current flowing."

Jan 1, 2000

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003

By Emmanuel N. Zevgolis

In the present work, a reduction roasting experimental study of Greek nickeliferous laterite samples with a gaseous reducing mixture ? CO:N2- is presented. The effect of parameters such as temperature, ore grain size, and composition of the reducing mixture were examined. It is deduced that the reducibility of intermediate type laterite sample, where iron appears mainly in the form of goethite (a-FeOOH), is considerably higher than that of limonitic type laterite samples, where hematite (a-Fe2O3) is the predominant iron mineral phase. The degree of reduction of the limonitic type laterite samples does not exceed 50%, while it reaches 95% in the case of the intermediate-type laterite sample under the same experimental conditions. Increasing the temperature in the range 750-900°C does not considerably favor the reduction of the limonitic type laterites, whereas decrease of ore grain size of the limonitic-type ore samples and more intense reducing conditions increase the reduction. The considerably higher specific surface area values of the intermediate laterite samples, diminishes the effect of the ore grain size and this can be regarded as the critical parameter leading to the higher reducibility of this ore.

Jan 1, 2009

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Shengli Wu, Laixin Wang, Minyin Kou, Xinliang Liu, Weidong Zhuang, Yujue Wang

COREX process has obvious advantages in environment protection but still has some disadvantages, for example, it has a higher sulfur content of hot metal than blast furnace. In this paper, the thermodynamics and dynamics of desulfurization have been investigated to obtain the main operation parameters related to the mass fraction of sulfur in the hot metal. In addition, statistical analyses have been carried out to study the relationship between operating parameters and sulfur content of COREX hot metal based on actual plant data. It has been found that the mass fraction of sulfur in hot metal is significantly influenced by the C content in hot metal, MgO/Al2O3 in slag, the concentration of MgO in slag, the temperature of hot metal and binary basicity (R2).A linear model has been developed and subsequently used for reducing the mass fraction of sulfur in hot metal, improve the quality of hot metal and contribute to low carbon ironmaking.

Jan 1, 2016