Search Documents

By Alex Luyima, Honglan Shi, Lifeng Zhang, Yongqing Jiang

"Leaching process has been suggested to recover most metals from waste PWBs. In this study, the leaching behavior of most metals present in waste PWBs is evaluated before and thermal treatment. Different leaching acids: hydrochloric acid (HCl), nitric acid (HNO3) and aqua regia are compared. The effects of acid concentration, particle size of sample, leaching time and temperature are examined. Results revealed that most metals are present in small particle size and sequential leaching of PWBs with a combination of HCl acid and aqua regia is capable of dissolving most of the metals content of PWBs. Leaching of thermally treated PWBs produced the highest leaching percentages for similar leaching conditions.IntroductionApproximately 20–50 million tonnes of electronic waste (e-waste) is produced globally per year. Waste Electrical and Electronic Equipment (WEEE) or E-waste is one of the fastest growing waste streams in the world. In developed countries, it equals 1% of total solid waste on an average [1]. The growing stockpile of used and obsolete consumer electronics has been called the “largest toxic waste problem of the 21st century [2]. Printed wiring boards (PWBs) is an essential part of almost all WEEE, and accounts approximately 3% of all WEEE by weight [3]. PWBs are a platform upon which microelectronic components are mounted. PWBs contain metals (~40 wt. %), ceramics (~30 wt. %) and plastics (~30 wt. %) [4]. The metallic part includes; Cu, Pb, Zn, Fe, Cd, Be, Cr, Au, Pt, Pd, Ag, etc. The plastic part of the PWBs is mostly epoxy resins. These plastic resins also contain very toxic halogenated flame retardants (HFRs) [5]."

Jan 1, 2012

By M. Patel, G. Djambazov, J. Shrimpton

"Removing zinc by distillation can leave the lead bullion virtually free of zinc and also produces pure zinc crystals. Batch distillation is considered in a hemispherical kettle with water-cooled lid, under high vacuum (50 Pa or less). Sufficient zinc concentration at the evaporating surface is achieved by means of a mechanical stirrer.The numerical model is based on the multi-physics simulation package PHYSICA. The fluid flow module of the code is used to simulate the action of the stirring impeller and to determine the temperature and concentration fields throughout the liquid volume including the evaporating surface. The rate of zinc evaporation and condensation is then modelled using Langmuir's equations. Diffusion of the zinc vapour through the residual air in the vacuum gap is also taken into account.Computed results show that the mixing is sufficient and the rate-limiting step of the process is the surface evaporation driven by the difference of the equilibrium vapour pressure and the actual partial pressure of zinc vapour. However, at higher zinc concentrations, the heat transfer through the growing zinc crystal crust towards the cold steel lid may become the limiting factor because the crystallization front may reach the melting point.The computational model can be very useful in optimising the process within its safe limits.IntroductionLead bullion is commonly refined by removing various impurities (e.g. copper, silver, bismuth, antimony, etc) sequentially. This in normally achieved by the addition of reagents which selectively react with the impurities and the resulting compounds removed by various means. To aid efficient mixing (ensure uniform reactions), batch mixing of materials via the aid of impellers is common practice in a number of industrial sectors. Excess zinc, added during the desilvering process can be removed by one of three methods: (1) Vacuum dezincing - During vacuum dezincing, a vacuum is drawn on the agitated molten lead within a hemispherical vessel (Figure 1). Vaporized zinc condenses on the inner top surface of the vessel. The temperature at which zinc commences to vaporize lowers owing to heating under a vacuum. This enables vaporized zinc to be recovered in the form of high purity crystals without oxidation. The zinc crystals are recovered once the vessel lid is removed and the vacuum is broken. (2) Chlorine dezincing - In chlorine dezincing, molten desilvered lead is reacted with chlorine gas, forming a surface layer of zinc chloride contaminated with small amounts of lead chloride."

Jan 1, 2004

By Renato G. Bautista

The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions:. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.

Jan 1, 1996

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Guo Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By Zhangm Mingming

Three samples received from the EAF shop were characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work was to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus and to identify their origin and associations with iron minerals in the concentrate samples from the mines. The samples were identified as MINERAL, PELLET, and HRD. The latter is the DRI product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are the major sulfide minerals. Trace amounts of apatite [Ca5(PO4)3(F,Cl,OH)], wardite [Na4CaAli2(PO4)8(OH)8 6H2O], giniite [Fe;(PO4)4(OH)3 2H2O] and vivianite [Fe3(PO4)2 8H2O] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)2O4] in trace amounts in the mineral samples, respectively. Impurities carry over to the pellet and HRD samples. Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed in both the mineral and pellet samples, magnetic and flotation processing routes should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating processes (magnetic separation and flotation).

Jan 1, 2012

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Ted H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1993

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed_ This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels_ Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Laurence Whitty-Léveillé

Proper handling of the radioactive fraction associated with the production of rare earth elements (REEs) in the mining industry is essential for a sustainable environment and human health. Actinides, such as uranium and thorium, have similar chemical properties to REEs, and are often co-dissolved in current hydrometallurgical processes. This causes radioactive contamination of the infrastructure through the extraction cycle. The present study optimizes, through experimental design, a sequential leaching procedure with Na2CO3/NaHCO3 and HCl for the rapid and selective dissolution of REEs and actinides. Optimization focuses on the main operating parameters (time, temperature, and concentration); different types of minerals, REE composites, and ores; on achieving maximal leaching yield; and on minimizing dissolution of the gangue metals (Fe, Si, and Ca). The final sequential procedure was rapid (1 h), effective, and led to the segregation of Th, U, and REEs with limited dissolution of the gangue metals.

By Kiyoshi Takai

The Para-Eco Incinerator Ash Processing System for cleaning slag has been developed after a seven-year pilot plant study. The major part of the system is an electric furnace heated to 1773 K. The feed material consists of a municipal solid waste incinerator ash mixture containing a reducing agent of a coke and an inorganic flux of calcium and magnesium. With this furnace system, three kinds of products are produced. They are an inorganic molten salt that is slag, molten iron alloy absorbing non-ferrous metals, and fly ash. Due to the reducing atmosphere in the furnace, the slag does not contain any metal components as well as chlorine components just like natural rock and/or aggregate. A retreatment plant modifies this slag into a practically useful aggregate. The plant consists of a slow cooling step for crystallizing the slag as well as a water granulation step. The iron components in the ash are reduced to molten iron droplets, which concentrate at the furnace bottom. The non-ferrous metal components such as copper, chromium, and others are absorbed into the molten iron but not into the molten slag. Volatile metals such as lead, zinc, cadmium and others as well as sodium, potassium, and chlorine go back into the fly ash. A solvent extraction method and/or other appropriate procedures can be used to extract the metal components from this fly ash.

Jan 1, 2003

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By Roderick I. L. Guthrie, Donghui Li, Mihaiela Isac, Luis Calzado

The HSBC is an ideal process for the production of BMG strips. The purpose of the present work was to investigate the casting of Ca-based, bulk amorphous strips. The possibility of casting three Ca-based alloys (60Ca-20Mg-20Al, 60Ca-15Mg-10Al-15Zn and 55Ca-15Mg-10Al-15Zn- 5Cu (at.%).) was investigated, using the HSBC simulator. Numerical simulation and mathematical modeling were used to predict temperature variations and cooling rates, under different interfacial gaseous atmospheres (helium and air) near the meniscus region. Given the critical cooling rates and glass temperatures needed to be reached for the vitrification of the respective alloys, this leads to predictions of the critical thicknesses possible with this novel casting process. To validate our predictions, these alloys were then prepared and cast onto the sand-blasted, solid copper substrate mould of the HSBC simulator. The possibility of producing Ca-based metallic glassy strips via the HSBC processes was confirmed, using optical microscopy, X-ray diffraction and Scanning Electron Microscopy, to characterize the glassy properties of the cast strips. It was found that the HSBC process would be able to provide sufficient cooling to form amorphous strips for the 60CA-15Mg-10Al-15Zn and 55Ca-15Mg- 10Al-15Zn-5Cu alloys, but not the 60Ca-20Mg-20Al alloy.

Jan 1, 2014

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By Y. H. Wang, S. Kou

"Three-dimensional weld pool convection was computer simulated using dimensionless variables. The electromagnetic force, the buoyancy force and the surface tension gradient on the pool surface were treated through the use of the dimensionless electromagnetic force, the Grashof number and the Marangoni number. Other typical dimensionless numbers such as the Prandtl number and the Peclet number were also used. The calculated and experimentally observed fusion boundaries were compared. The convection patterns were shown and the effect of the Marangoni number was demonstrated. IntroductionSeveral weld pool convection models have been developed by Oreper et al. (1,2), Chan et al. (3) and Kou et al. (4). These models describe two dimensional convection in stationary weld pools in a semi-infinite workpiece. Since the vast majority of arc welding practices involve a moving heat source and weld pool, and the workpieces are finite in thickness rather than semi -infinite, a 3-D convection model for a moving heat source and a workpiece of finite thickness is expected to be much more useful.Weld pool convection can strongly affect the structure and properties of the resultant welds. Variations in weld characteristics which are likely to occur from changes in weld pool convection are: weld penetration, macrosegregation, gas porosity, solidification structure, undercutting and surface smoothness. Apparently, the quantitative understanding of convection and heat flow in weld pools is of considerable practical interest. Mathematical models describing convection and heat flow in weld pools are essential, not only because of the quantitative understanding they provide, but also because of the difficulties associated with the experimental measurements of weld pool convection. These difficulties are mainly due to the fact that only surface flow, rather than the overall convection pattern in the weld pool, can be observed. In fact, due to arc glow even the observation of surface flow can be rather inconvenient."

Jan 1, 1986

By Dao-Wu Yang, Ju-Lan Zeng, Li-Xian Sun, Yan Yao

"The hydration heat of the pure cement, the fly ash single-dopped cement, as well as the fly ash and fluorgypsum co-dopped cement were investigated by means of micro-calorimety with an eight-channel micro-calorimeter (TAM Air). The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the fly ash and fluorgypsum co-doped cement was appeared earlier than the fly ash single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of the doped cement were reduced, and the exothermic peak appeared later. The effects of fly ash and fluorgypsum on the compressive strength of cement were also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the fly ash single-doped cement. Based on the experiment results obtained in this paper, we could conclude that fluorgypsum is a suitable additive for fly ash-doped cement.IntroductionFly ash and fluorgypsum are industrial waste. In 2008, nearly 400 million tons of fly ash has been produced by coal-burning power plants in China. And it is estimated that this number would exceed 500 million at the year of 2015. Besides, every year the fluoride salt factories in China discharge more than 100 million tons of fluorgypsum. Tremendous of fly ash and fluorgypsum occupy considerable land and contaminate air and water sources [1]. As a result, comprehensive utilization of this two industrial waste has draw great attention from all over the world.Cement is the most-used construction material on earth. But the production of cement consumes huge energy and destroys the environment. This problem might can be partly solved by applying fly ash and fluorgypsum as additive for cement [2-4]. During the last decade, some papers that focused on applying fly ash and fluorgypsum as additive for cement have been published [5, 6]. However, to the best of our knowledge, none of these papers investigated the hydration heat of the fly ash and fluorgypsum co-doped cement.The hydration of cement is an exothermic reaction, which can result in serious problem for mass concrete: The interior of the concrete could reach very high temperature as the hydration proceeded [7-9]. As a result, the great temperature difference between the interior and the outer of the concrete would exist and cause serious thermal stresses. Thus, the concrete would be destroyed by the cracks which in tum are resulted from the thermal stresses [10, 11]. The heat released by the cement hydration and the hydration rate is commonly regulated by adding mixed materials or transferring additive such as fly ash and fluorgypsum [12-14]."

Jan 1, 2011

By Mick O'Meara

Metal Organic Chemical Vapour Deposition (MOCVD) is used in the production of computer circuit boards and metal shapes in nickel, gold, copper, cobalt, etc. All varieties of .MOCVD use the decomposition of a vapour of organometallic compounds to produce different forms of ultra-pure metals, or alloys. CVD Manufacturing's proprietary MOCVD process has been adapted and developed to produce commercially ultra-pure metal shapes, metal powders, and metal foams. Therefore, it is a purification process. The typical process has three steps. First, a volatile metal organic compound is produced from volumetrically contaminated metals, metal oxides, etc. Typical feed materials are metal powders, ores, concentrates, or a slurry of metals and contaminants. Secondly, the volatile. metal organic compound is purified by fractional distillation. Thirdly, the purified metal organic compound is decomposed into different forms of ultra-pure metals, such as net shapes, powders, or metal foams. A mixture of metals can be purified either by the selective production of volatile materials, or a separation can be achieved during the second step, in the fractional distillation stage. The purification and recycling of metals by the MOCVD process will be discussed, particularly with regard to nickel, aluminum, gold, the platinum group and other metals.

Jan 1, 2000

By Takeshi Azakami

By combining the iron reduction process with the usual rotary kiln process, the direct production of metallic zinc from EAF dust is proposed. After thermodynamic estimation and desk-top experiments it is confirmed that the process is hopeful under suitable conditions. In order to get some practical test data the enlargement of the process scale was planned and the bench scale tests were carried on successfully. In these experiments a zinc ingot of PW grade was produced from EAF dust.

Jan 1, 2003