Search Documents

By Min Chen, Zhen Tian, Hongxu Cui

"The effects of adjusting technology on the phosphorous enrichment in converter slag were investigated. The results showed that the grain size of 2CaO·SiO2 with high phosphorus containing content increased slightly with the decreasing of cooling rate, and the proper cooling rate was confirmed to be about l.0°C.min-1. Moreover, the morphology of the phosphorus-rich phase of 2CaO·SiO2-3CaO·P2O 5 was changed from granular for the higher basicity of converter slag to the coexistence of granular shape and rod-like for the lower basicity of adjusted slag. With the addition of adjusting agent such as SiO2 to lower the basicity of converter slag, the phosphorus in converter slag could be transferred into 2CaO·Si02 phase effectively, and P2O 5 content in high phosphorus containing phase reached to above 30%.IntroductionThe yield of converter slag is very large in China, but most of the slag is stacked usually after the separation of iron, which not only takes up a lot of land, but also affects the ecological environment seriously. Therefore, improving the comprehensive utilization and value-added products of converter slag is of great significance to recycle the steelmaking slag[l-3]. On the other hand, the refining of hot metal with high phosphorous content is an unavoidable problem with the decreasing of high grade iron ore, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. However, the current recycle of converter slag is more focused on the emission reduction and reuse of steelmaking slag inside the iron and steelmaking process without considering the recycle of phosphorous resources[4-6]. At the same time, the development and utilization of phosphate ore as a strategic resource is drawing more and more attention, but the phosphate ore in China is mostly low grade and significant amounts of tailings are produced which is harmful to the environment. Therefore, it is important to separate phosphorous resources in steelmaking slag which can be used as phosphate ore for fertilizer material[7-9].Literature studies showed that most of the phosphorus in steelmaking slag existing as 2CaO·SiO2-3CaO·P2O 5 solid solution phase in 2CaO·SiO2 particle. The P2O 5 content in the phosphorus containing phase is very low due to the fact that the basicity of converter slag is usually high and the precipitated amounts of 2CaO·SiO2 particles during cooling are very large, resulting in the fact that the P2O 5 contents in 2CaO·SiO2-3CaO·P2O 5 solid solution phase are much lower which is impossible to be used as phosphorous resources instead of phosphate ore. Thus, the enrichment of phosphorus in steelmaking slag is need[ 10-14]."

Jan 1, 2011

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By Go-Gi Lee, Jae-Young Jung, Myung-Duk Seo, Hyun-Na Bae, Seon-Hyo Kim

"Bubbles form at the anode during the electrowinning of magnesium and cause hydrodynamic acceleration and electrical field disturbance. A three-dimensional computational model was developed to investigate the effects of the geometry of the electrochemical chamber and the size distribution of bubbles on the fluid flow in the pilot plant. The results are validated by measurements of the surface characteristics of molten salt and the bubbles formed. Fluid flow at the surface was recorded with a high speed camera, and the distribution of bubble size is determined by inspecting the video images frame by frame. The measured size distribution of the bubbles is entered into the computer simulation of a multi-phase flow. A sloped roof is installed above the electrodes, to enhance the flow of the molten salt, thus resulting in higher current efficiency, lower energy consumption, and higher quality of magnesium metal.IntroductionTitanium's excellent properties of low density, high specific strength, high temperature strength, and exceptional resistance to corrosion are highly beneficial to diverse applications including aerospace, automotive, construction, and medical implants. Although the Kroll process[l] and Hunter process have been used for the extraction of titanium in the 20th century, their complicated engineering stages and high production cost, have led to further research into new processes such as FCC Cambridge, Armstrong and TiRO. Despite these intense research efforts, no process has yet been developed that is more economical than the Kroll process, by which most of the global commercial titanium is still being produced."

Jan 1, 2011

By Min Chen, Nan Wang, Zhen Tian, Yingying Shen

"The enrichment behavior of phosphorus in CaO-SiO2-FeOx-P2O5 slag was studied by making an investigation on the distribution of phosphorous content in slag and 2CaO·SiO2 phase. The research results showed that the existing 2CaO·SiO2 solid particles in slag were the sites for the phosphorous enrichment. The enrichment process of phosphorus in CaO-SiO2-FeOx-P2O5 slag can be recognized as: mass transfer of phosphorus from bulk slag toward the surface of 2CaO·SiO2 particle, superficial dissolution reaction of phosphorus to 2CaO·SiO2 and diffusion of phosphorus through the product layer of 2CaO·SiO2-3CaO·P2O5 solid solution to the inner of 2CaO·SiO2 particle. Compared to the 2CaO·SiO2 particles with larger size (500µm to 1000µm), the completion time of enrichment was shorter for the particles with smaller size (less than 50µm).IntroductionDuring ironmaking and steelmaking, significant amounts of slag are produced. Contrast to the high utilization of ironmaking slag, the treatment of steelmaking slag is more difficult and challengeable, and therefore, an alternative approach is to recycle the steelmaking slag inside the ironmaking and steelmaking process itself. The main limitation to the reuse of steelmaking slag inside the process is that the refining process may be aggravated caused by the phosphorous accumulation if it is used in the blast furnace burden [1]. At the same time, the phosphorous content of steelmaking slag (approximately 1%~5% P2O5) is too low for it to be used as raw material for fertilizer [2, 3]. Moreover, owing to the diminishing supply of global iron ores with low phosphorous content, the control of phosphorus in iron and steelmaking processes has become an increasing problem, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. Therefore, a valuable approach is quite appreciated in which the steelmaking slag is recycled within the ironmaking and steelmaking process and at the same time, the high phosphorus-containing phases in the steelmaking slag, suitable for use as fertilizer can be separated and recycled effectively [4]."

Jan 1, 2011

By Moenster J. A., M. J. Sankovitch

Doe Run's Buick Smelter was converted from a primary lead smelter to a secondary lead smelter in 1991. The recycling facility was designed to produce 60,000 tons of refined lead per year from 110,000 tons of spent starting-lighting-ignition (SLI) batteries and 10,000 tons of lead contained in drosses and scrap. Since commissioning, Buick's refined lead output has steadily increased to exceed 120,000 tons for 1999. The production gains have been the result of continuous process improvements, empowerment of the workforee, and development of additional scrap lead streams. The production gains were accomplished while setting industry standards for employee safety, reducing plant environmental emissions and employee blood leads, achieving ISO 9002 certification, and expanding product lines to meet customer requirements. This paper highlights Buick's major accomplishments through the 1990's.

Jan 1, 2000

By Minge Zhao, Yuandong Pei, Zhixing Zhao, Zejun Ma, Lili Ban

"Confocal scanning laser microscope (CSLM) has been applied to carry out the in-situ observation of melting and solidifying characteristics during iron ore sintering process, accompanied with TG-DSC test. It can be found that apparent Liquid phase forming temperature(LFT) and ending solidifying temperature(EST) is about 1190? and 1160?, respectively. Forming liquid phase during sintering process goes through four courses, these are shrinking, expanding, shrinking and expanding coexisting and expanding totally. For Yandi fine, the corresponding temperature of these four courses is about 1120-1160?, 1190-1196?, 1218-1220? and 1233-1270?, respectively. Although CAJ fine has more difficulty in forming initial liquid phase, but when liquid phase expands, it may have better fluidity and easier for liquid phase formation. Adding enough CaO, CAJ fine takes on high fluidity like Yandi fine, because liquid phase during sintering process is formed mainly by reaction between CaO and Fe2O3.IntroductionConfocal scanning laser microscope (CSLM for short) has been applied to carry out the in-situ observation of metallurgical phenomena, especially in steelmaking process. Recently, many researches on ironmaking process were conducted with CLSM. While for high temperature properties during sintering process, there are limited reports on in situ observation1-2). In this paper, melting and solidifying characteristics of iron ore were observed with CLSM under simulated sintering temperature, and high temperature properties of iron ore during sintering process was clarified based on the in situ observation results and TG-DSC research."

Jan 1, 2012

By D. I. Davidov, D. A. Shishkin, M. B. Rigmant, E. P. Romanov, N. N. Stepanova, N. V. Kazantseva

The Co-19 at.%Al-6 at.%W alloy was prepared by two methods of casting. We used arc melting under an argon atmosphere with casting into a copper water-cooled casting mold and induction melting furnace with casting into a ceramic Al2O3 mold. According to the X-ray and SEM analyses, phase compositions depend on the cooling rate of the ingot after melting. After arc melting, the cast alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co3W (DO19) type. After the induction melting, the alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co7W6 () type. All phases in the investigated ternary alloy at the room temperature are ferromagnetic. Curie temperatures of all obtained phases were defined. It is shown that the magnetic properties of the studied alloy are typical for soft magnetic materials.

Jan 1, 2015

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By Paul O. Malan

"The Tusc gold deposit is located along the Carlin Trend approximately 13 kilometers north of Carlin, Nevada and 2.5 kilometers northwest of the Gold Quarry mine. Tusc is one of several structurally controlled oxide gold deposits located along the Good Hope fault within the Maggie Creek subdistrict. Mining commenced in 1994 with an oxide reserve of780,000 troy ounces of gold at an average grade of 1.34 g/t Au. The Good Hope fault forms the southwestern edge of the Schroeder Mountain uplift (also known as the Carlin Window) and juxtaposes carbonate rocks of the Siluro-Devonian Roberts Mountains Formation against siliceous mudstone, siltstone, and silty limestone of the Devonian Rodeo Creek unit. Submicroscopic gold mineralization is disseminated in the Good Hope fault system and in fractured hanging wall carbonate rocks. Wallrock alteration includes silicification, deca!cification, sericitization, and late alunite replacement and veins. All Tusc ore is transported 2.5 kilometers to Gold Quarry for processing. Leach-grade ore (0.2 - 1.7 g/t gold) is placed on the oxide leach pads, and mill-grade ore(> 1.7 g/t gold) is processed through the CIL oxide mill. IntroductionThe Tusc gold deposit is located in Eureka County, Nevada, U.S. A, approximately 13 kilometers north of the town of Carlin and 2.5 kilometers northwest of the Gold Quarry mine (Fig. 1 ). Tusc is one of several open-pit, oxide, gold deposits within the Maggie Creek subdistrict of the Carlin Trend. Tusc is a structurally controlled gold deposit located along the Good Hope fault. Submicroscopic gold mineralization is disseminated in the brecciated and silicified Good Hope fault zone and along intersecting northeast and northwest striking structures."

Jan 1, 1997

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Herman Wotruba

Mercury emissions and other environmental impacts in small-scale gold mining are a world-wide problem. "Clean" or better: "Cleaner" technologies have -apart from being environmentally sound -to guarantee a higher income and better working conditions for the miners in order to have a chance for long-term acceptance. In small scale primary gold mining in several South American countries, a number of techniques have been adapted and improved so that they not only were accepted due to their efficiency and easy handling, but they could also significantly lower mercury emissions.

Jan 1, 2003

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By Nexhmedin Lohja

The production of high-carbon ferrochromium in a submerged electric furnace based on double-level technology has some advantages compared to close-type furnaces with one tap hole. These advantages include the reduction of the specific energy consumption for the overall process, good separation of ferrochromium from slag, an effective treatment of raw materials including lean chrome ores (low percentage of Cr2O3) etc. An outline of the operation of this furnace along with the production line of briquettes from fines of chrome ore by using organic and inorganic binders, will be followed by a description of the recent work carried out to improve the energy consumption in this furnace through a pre reduction process of Cr2O3 ores by the off-gas energy recuperated from the furnace and the use of SiC in the feed. A short theoretical analysis of the new work will also be given.

Jan 1, 2006

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Viviane Tavares Moraes

"The development of mobile phone technology has increased the replacement of outdated equipments for more modern models, transforming disposal of such devices into a serious environmental problem. Recycling appears as an attractive alternative to minimize the environmental impact of disposing such large quantities. Recycling can be accomplished by treating the printed circuit boards of used mobile phones by using the same techniques used in ore treatments with hammer mill; magnetic separation, electrostatic separation and grain size range. Before performing the recycling process a PCB characterization was performed to identify the fraction with the higher metals concentration/content. This study demonstrated that the electrostatic separation was not the best metals concentration of PCB aiming the recycling, while the non-magnetic residue had presented a more significant metal concentration. Furthermore, after the magnetic separation was possible to separate the following metals: iron and nickel.IntroductionPortable electronic devices have gained increasing acceptance over the last decades. Mobile phones sales in Brazil, for instance, have reached 104 million in 2007, and 128 million in 2008. It is estimated that, around the world, 100 million mobiles are thrown away every year, either because of loss of functionality or because newer models are launched in the market [1,2, 3]. Printed circuit boards in mobile phones are made of many materials, with approximately 83% in weight being metals and fiber-glass, and the balance being plastics pl. Several metals can be recovered from the electronics waste, such as copper, tin, iron, lead, nickel, titanium, aluminium as well as some precious metals such as gold, silver and palladium [4, 5, 6, 7, 8]. Concurrent with the increasing world demand for copper, there average metal content in ores has been decreasing. Economically interesting copper mines used to have 4% metal content, whereas presently, such content is around 1%, i.e., for every 1 ton of ore extracted, only 10 kg are copper [9, 10]. Approximately 33% of printed circuit boards (PCBs) composition is copper, that is, for every 1 ton of PCBs waste, 330 kg are copper [1]. Research in recycling PCB waste focuses on mechanical, electrometallurgy, pyrometallurgical and hydrometallurgical processes [3, 8]. Collecting and recycling obsoletes electro-electronic equipments is very important these days, in order to, not just preserve the non renewable natural resources but also to keep the environment and the population safe from the pollution caused by the toxic materials and heavy metals present in this kind of waste."

Jan 1, 2011

By John M. Boyle

The use of high vacuum mercury retort recovery as a safe and effective means of removing mercury from mercury hazardous waste solids rendering them non-hazardous and recovering mercury suitable for recycling.

Jan 1, 1995

By Atsuhiro Nabei, Ken-ichi Yamaguchi

"Wet chlorination process of de-copperized anode slime is followed by de-chlorination stage in which lead-sulfate and metallic silver form silver residue. The silver residue is subsequently reduced to Ag2Se matte and PbO-SiO2 slag to remove lead to the slag in a short rotary furnace. Although this smelting process is proven well in actual operations, few papers have investigated its metallurgical aspects. This paper will describe the effectiveness of controlling parameters adopted at the Naoshima Smelter & Refinery and discuss the decisive factors influencing silver loss to PbO-SiO2 slag.IntroductionThe precious metals plant at Naoshima smelter & refinery was established in 1989, and has produced electrolytic silver, refined gold and platinum-group metals (PGM) from de-copperized anode slime as by-products of electrolytic copper. The process for gold production has been innovated from conventional smelting process to hydrometallurgical process since 2004 [1], while the process for silver production has still remained the same.The process for silver production at the Naoshima smelter & refinery is illustrated schematically in Figure 1. De-copperized anode slime is, at first, concentrated in the froth flotation process, then leached in the wet-chlorination process, and converted to silver residue in the de-chlorination process. The silver residue, which is a mixture of lead-sulfate and metallic silver, is charged to a short rotary furnace for the oxidation roasting to volatilize selenium dioxide and subsequent reduction smelting. In the smelting stage, silver residue and reverts containing selenium are smelted with flux and carbonaceous materials to form PbO-SiO2 slag and Ag2Se matte. Furthermore, Ag2Se matte is transferred to a rotary cupell and oxidized by air with the addition of sodium carbonate and sodium nitrate to produce silver anodes while removing impurities into litharge. Silver anodes are electrolytically refined by the Moebius process. Electrolytic silver is washed, dried and, finally, cast into 30kg-bars."

Jan 1, 2011

By Toshihide Takenaka

The management of radioactivated stainless steel from a terminated nuclear reactor will become an important subject in the near future. The separation of the elements in stainless steel should be effective to reduce the management labor. In this study, the separation of the elements in stainless steel by an electrorefining tcchnique was investigated in an aqueous solution. The electrochemical reactions of the elements in stainless steel werc studied by voltammetry and potentio-static electrolysis was carried out. A stainless steel anode was dissolved electro-chcmically with good anodic current etliciency in a chloride solution. The residue, where Ni was concentrated, was found on the anode after electrolysis. The electrodeposit in a stainless steel cathode consisted mainly of Fe and Cr and the Ni content in it was less than 0.5wt% under suitable condition. It is concluded that an electrorefining technique is effective for the separation of the elements in stainless steel.

Jan 1, 2003

By Roderick Guthrie

Gas injection into liquid steel baths is widely practiced, ever since the early days of Bessemer’s pneumatic steelmaking process. What has not been fully appreciated is the critical role of bubble sizes for delivering higher quality commercial steels than is presently possible. This was first proposed by Prof P. Hayes and his research group. Using a full-scale water model of a typical 4-strand Ladle-Tundish-Mold system, we demonstrate the potential advantages of modifying a typical ladle shroud, to generate microbubbles within the water flowing into the tundish. This is possible by taking advantage of high shear rates and turbulence kinetic energy available in that region. These microbubbles enhanced the removal of “micro-inclusions” (hollow glass microspheres) in the 5–50 micron size range, to the upper surface of the tundish. There, they were absorbed into an overlaying “slag” phase. Accompanying CFD studies confirmed that no microbubbles in the size range generated (500–900 μm), pass through the submerged entry nozzles into the moulds.

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDSIM metals precipitation system to treat a waste stream containing scrubber blowdown and process water from a smelter operation. The combined stream contained cadmium, lead, selenium, arsenic and zinc, plus some iron and copper. Treatment requirements included meeting stringent mass flow limitations for specific heavy metals. The HDS ? system can reduce the arsenic from 600 ppm to less than one ppm. The process generates a dense sludge that can be reprocessed in a smelter, eliminating the liability associated with landfilling. Flow diagrams and process details are discussed.

Jan 1, 1994

By G. Belardi

A study has been conducted to assess a new wet beneficiation treatment for the recovery of the sulphuric-acid-soluble titanium oxide contained in the waste from an Italian TiO2-pigment facility. The waste is produced during treatment of a Ti-enriched slag and contains as main components TiO2 (54%, of which 42% acid-soluble and 12% insoluble), SiO2 (27%) and A1203 (6%). Eighty percent of the material is finer than 50pm. The first step was to ascertain the possibilities offered by size classification, wet gravity separation, froth flotation and wet high-intensity magnetic separation to improve the grade and recovery of Ti02 and reduce the SiO2 content. The next step was to optimize the operating conditions of the various separations and assemble them into a complete flow- sheet. Beneficiation ensures potentially 70% recovery of the TiO2 with a concentrate grade of 80%.

Jan 1, 1998