Search Documents

By K. Koike, N. Masuko, Y. Takasaki

At the Zinc & Lead'95 symposium, one of the authors presented several modifications of Pb-Ag-Ca alloy anodes for the zinc electrowinning process, and also, the behavior of some organic additives in the electrolyte. In this study, the mechanical properties of the electrode materials composed by Pb-0.5 wt% Ag-(0~0.8) wt% Ca were studied by the tensile and Vickers hardness methods. Furthermore, experimental research on the influence of rolling and annealing treatments on the electrolytic behavior and mechanical properties of these alloys was carried out. The tensile strengths of the annealed Pb-0.5 wt% Ag-(0.1-0.8) wt% Ca alloys were the same or higher than those of the as-cast Pb-0.9 wt% Ag alloy. The anode potential using the as-cast Pb-0.5 wt% Ag-0.6 wt% Ca alloy decreased compared to the as-cast Pb-0.9 wt% Ag alloy. Moreover, the annealed Pb-0.5 wt% Ag - 0.6 wt% Ca anode after rolling showed a lower anode potential than the as-cast Pb-0.5 wt% Ag - 0.6 wt% Ca anode.

Jan 1, 2000

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By Juan B. Cabezas

"The favorable characteristics and workability of plastics as a replacement of wood, lead, stainless steel, asphalt and other materials are described. Various types of plastic have proven to be the most favorable choice for handling a variety of acidic, alkaline and organic solutions, as well as pulps, chemical wastes, slurries or tailings for impoundments. The material origin of various plastics, methods of manufacturing and specifications applied to leaching solutions are discussed, including availability and costs. Examples of select plastics are considered for use as alternatives of other materials under severe environmental requirements.IntroductionHydrometallurgical processes applied to gold recovery, as well as other metals, require the use of strong solutions of alkaline, acidic or organic nature, and may also include a variety of materials with extraneous characteristics and complications for handling in storage.The technology of leaching has been in use for more than 100 years, but the applications of leaching processes in metallurgy have become more commonly used in the last 15 years. Suitable materials for the construction of containers, launders, piping, and various accessories, to be used in the handling of leach solutions or slurries, have become a serious problem. Various metals such as brass, lead, stainless steel, etc., and non metallics including wood, clays, glass, rubber, ooncrete, tars or miscellaneous compounds have been tried in the past with serious limitations in workability and resistance to wear and corrosion. For example, the use of metallic, wooden or glass piping systems would require extraordinary shop maintenance to keep such systems in operation"

Jan 1, 1997

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By Richard D. Hagni

The United States is dependent upon foreign sources for more than 93% of its bauxite and alumina supply. Domestic production of bauxite, which comes from Alabama, Georgia and Arkansas, is limited to those bauxite ores containing less than about l ½ % iron. Bauxites with higher iron contents are generally not utilized because they cause problems in bauxite calcining and especially because they produce undesirable brick discoloration and cracking. In order to improve beneficiation and expand the utilization of high-iron or ferruginous bauxites, a mineralogical and textural study has been conducted on selected samples from the Eufaula, Alabama, bauxite district. Reflected light microscopic, petrographic, and X-ray techniques have shown that a variety of iron minerals are present, including hematite, goethite, lepidocrosite, siderite, pyrite, marcasite, and ilmenite. Although the iron minerals may be locally concentrated into concretions and pisolites, most occur as very fine grains that are disseminated and show a variety of intergrowths. Mineralogical and textural observations indicate that the fine-grained iron mineral grains may be amenable to high gradient magnetic separation.

Jan 1, 1981

By Cristiän Vargas, Jaime Simpson, Gerardo Cifuentes

"This paper presents a new process for the precipitation of Sb and Bi present in copper refinery electrolytes in the presence of Pb02 (Chilean Patent No. 45,037). To establish the conditions under which the precipitating compounds form, it was necessary to evaluate the amount of PbCh consumed, antimony extraction efficiency, precipitate stability, reaction kinetics, diffraction analysis and X-ray fluorescence, separation of size, plus observation of the precipitates in the electron microscope. Preliminary tests were carried with synthetic copper refinery electrolyte, and then the final testing was done with electrolytes from Chilean refineries. This process provides a real alternative for the treatment of copper refinery electrolytes for the control of Sb and Bi in solution; it is very simple to operate and is low cost compared with competing processes.Introduction.A high quality copper cathode implies a cathode free of impurities. The electrorefining process seeks to eliminate these impurities from the copper anode (99.5% purity) by its dissolution in an acid electrolyte using chemical and electrochemical reactions. As a result of this process, a cathode (99.99% purity) is obtained. If the concentration of impurities in the electrolyte, from the dissolved anodes, begins to increase; particularly if the antimony concentration in the electrolyte increases up 500 ppm, the formation of floating slimes which are a major cause of contamination of the cathode is favoured. The most important impurities from the point of view of their effect on the quality of the cathode copper, are Ag, As, Sb, Bi, Pb, Se and Te. Silver is necessary for the control of Se and Te. To control all of these impurities, it is necessary to establish different methods or parameters of control in copper electrorefining. These parameters are anode composition, additives, purification of the electrolyte, current density, acidity, etc."

Jan 1, 2012

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By Paul Dewison

For nine years, from mid-1987 to mid-1996, the copper market enjoyed what appeared to be an endless boom in which prices were much higher relative to production costs than for most other base metals. After the boom ended abruptly mid-1997 with the Sumitomo affair, copper was burdened by an overhang of new projects that promised to swamp demand in what, with the Asian financial and economic crisis of 1997, had become a considerably worse consumption environment. Now, demand prospects do not look so bad. If, as we suspect, we will be dealing with a more rational market in the future, it becomes all the more important to forecast accurately the prospects for consumption. In this paper, we present a new methodology for copper demand forecasting. The methodology forms the backbone of the demand-side analysis for the multi-client study entitled "Long Tenn Outlook for Copper", co-authored by Metalica Ltd. and Bloomsbury Minerals Economics (BME). Key components of the methodology are as follows. (1) Relate demand to economic structure. (2) Focus on products rather than refined consumption. (3) Apply a consistent products/applications analysis to all countries and time series. (4) Incorporate scrap market dynamics within the analytical framework.

Jan 1, 1999

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By A. F. Otero

During the electrowinning (EW) of copper significant quantities of highly toxic vapors (acid mist) are produced due to the liberation of oxygen at the cathodes. Acid mist affects the health of operators, the environment and plant infrastructure. Acid mist can be decreased to acceptable levels by a combination of physical means (e.g. ventilation, plastic spheres over electrolyte) and chemical surfactants that decrease the surface tension of the electrolyte, modifying the way oxygen bubbles burst at the surface of the electrolyte. However, only few chemical surfactants are compatible with electrolytic applications, and they are not always used due to their high costs. This paper describes the application of a novel surfactant of natural origin (commercial name Mistop®) to suppress acid mist in copper EW process. Mistop® contains triterpenic saponins derived from the Chilean quillaja tree Quillaja saponaria Molina. The product is non-toxic, and poses no risks to the environment or to EW operators. Mistop® was tested at a laboratory, pilot plant and industrial scale in the world?s largest copper EW production plant at Radomiro Tomic (RT), CODELCO, Chile. At a Mistop® dosage of 8-9 ppm, acid mist decreased below the value accepted by Chilean regulations (< 0.5 mg/m3). At this dosage, Mistop® represents and economical alternative to chemical surfactants, and it is currently industrially used at RT.

Jan 1, 2003

By Ramasamy Santhanam

"India’s present annual marine fish catch is 2.9 million tonnes and its low value fishes such as sardines, sciaenids, goat fishes and leiognathids amount to 60%. The fish meal obtained from these resources is mainly used presently as an ingredient in live stock and aquaculture feeds. These fishes offer vast scope in the production of pet foods. Pet foods prepared with leiognathid fish meal (60%), maize flour (10%), wheat flour (5%), vitamin and mineral mixture (5%) and water (20%) and experimented with 50 cats and 50 dogs were found to be ideal. Depending on protein level, feeds are being formulated for experimenting with more number of pet animals. Training programmes are also planned for unemployed people to popularize pet foods for commercial purposes.IntroductionIndia’s present annual marine fish catch is 2.9 million tonnes and low-value fishes sucha s sardines (Sardinella albella, s. gibbosa, S. fimbriata and S. melanura); sciaenids (Otolithus spp. and Jhonius dussumieri); engraulids (Stolephorus indicus); and leiognathids Leiognathus bindus, L. equilus and Gazza achlamys) constitute 60% (Figure 1)[1]. The fish meal obtained from these resources is now mainly used as an ingredient in livestock, poultry and aquaculture feeds. Considering the rich nutritional status of these low-value fishes, it is felt that these resources could be converted into value-added products viz. pet foods."

Jan 1, 2008

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Cheng Fang, Zhou Lie-xing, Peng Jin-hui, Guo Sheng-hui

This article discusses the behavior of temperature and microwave thermo gravimetric analysis characteristic of ammonium paratungstate in a microwave field. Experimental results show that when 12g of material is place in a microwave with 900W of power, paratungstate’s temperature rises at 70°C/min. This results in paratungstate’s temperature being 980°C after 14 minutes. Compared with thermo gravimetric analysis characteristic, former two-step process of paratungstate microwave calcined completed ahead of schedule, after two-step process reaction is more intense,Paratungstate warming is more rapidly, the reaction time is much shorter; According to XRD and SEM, the product is high purity, the crystal particle size is uniform, and the grain size is fine.

Jan 1, 2015

By Andy Judge

"In traditional Permanent Magnet Machines, such as electric motors and generators, power is transmitted by magnetic flux passing through an air gap, which has a very low magnetic permeability, limiting performance. However, reducing the air gap through traditional means carries risks in manufacturing, with tight tolerances and associated costs, and reliability, with thermal and dynamic effects requiring adequate clearance. Using a magnetically permeable, high thermal conductivity material has the potential to improve magnetic performance, while at the same time offering performance advantages in heat transfer.Ferrofluids can be used to improve permeability in the rotor I stator gap. However, there are several tradeoffs in this approach. Fluid immersion comes with an increase in fluid friction loss compared to the windage losses of a traditional system. Isolating the rotating components from the ferrofluid can offset this effect. Also, while the magnetic effect can be positive for gap permeability, leakage flux can increase, and saturation can limit gains. These effects must be taken into account for a system optimized for ferrofluid immersion.IntroductionPermanent Magnet Machines (PMM's) convert electrical energy to mechanical energy in motor applications, or, for generator applications, convert mechanical energy to electrical energy through means of passing alternately polarized magnets past electrical coils. Looking at a simplified version of a PMM, where Rx is magnetic reluctance and <l>x is magnetic flux, we have the circuit shown in Figure 1."

Jan 1, 2013

By Jeff M. Kuhn

A new solvent extraction process for the removal of halides from zinc sulphate solution was tested in pilot plants at both a 0.1-L/min scale and at a 3-L/min scale. Teck Cominco?s process is called the HalogonTM process, for which patents are pending. Mixer-settlers were used for the 0.1-L/min pilot scale and two BATEMAN pulsed columns for the higher rates. Pilot testing was performed with commercial zinc sulphate solutions containing variable amounts of chloride and fluoride. Sulphate extraction was also controlled and deleterious halides were loaded and stripped into a form suitable for disposal. The engineering aspects and economics of this solvent extraction process for halide removal are also reported.

Jan 1, 2003