Search Documents

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Kenneth A. Brunk

"This address discusses how ""Mineral Processing Technology"" can play a major role in the life and profitability of a mining company. Examples of past and present technological breakthroughs and their impacts will be examined. Also, the future of processing technology will be emphasized.IntroductionThis talk will center on the role of technology as an important component of a business plan for mining companies. I'll attempt to explain how I see technology development as an underpinning of a successful mining company. We will examine an example of a technology that has resulted in a re-birth of segments of the industry, examine a technology life cycle and discuss technology as it relates to ore reserve replacement. Also, we will touch on technology in today's mining company and propose some food for thought for those designers of corporate organizations."

Jan 1, 1997

By Liu Zhonghua

Hydrogen reduction of cobalt sulfide (Co9S8) was experimentally investigated in the temperature range 813-1053 K. The results revealed that the reaction kinetics can be described by the shrinking core mod¬el in chemical control regime at low temperatures, it is of first order with respect to hydrogen concentration, and the reaction activation energy is 67.4 kJ/mol. The SEM second electron images of the samples before and after experiments showed that the swelling of the sample above 973 K is due to the formation of metallic cobalt whiskers.

Jan 1, 1992

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By Kazuya Kitatani, Gen Sasaki, Naoto Ohta, Hideharu Fukunaga, Makoto Yoshida, Jin Pan, Kenya Nagahisa, Toshihiro Ishikawa

"A sintered SiC (Tyranno-SA) fiber-reinforced MAS glass matrix composite was fabricated by using a slurry infiltration method and hot-pressing. The microstructure and mechanical properties were investigated: To prepare the preform, the MAS glass slurry including a dispersing agent was infiltrated into a bundle of the fibers. The preform was then hot-pressed under the conditions of 1473 K, 30 MPa, 3.6 ksec. A unidirectionally-reinforced oxide matrix composite with 50% Vf. of the fiber and a density of 2.84 g/cm3 was obtained. As the mechanical properties at room temperature, the three-point flexural strength- and quasi-static adsorbed energy were 500 MPa arid 6,000 J/m2, respectively. Without graphite or an h-BN pre-coating on the surface of the fiber, pull-out and bridging of the fibers from the matrix was found, and this leads to a high value of the adsorbed energy. By TEM observation, nano-scale crystalline products were found between the fibers and the glass matrix. The push-out test reveals that this layer causes the appropriate debonding of the interface during the fracture process of the composite.Introduction It is known that the CFCCs (continuous-fiber-reinforced ceramic matrix composites) are characterized by their non-linear fracture behavior, which is' hardly found in monolithic ceramic materials. It is inevitable for the CFCCs to exhibit a large fracture toughness so 'that debonding of the fiber/matrix interface; pull-out and bridging of the fibers then' occurs during the fracture process. This series of fracture behavior is known as the so-called ""the mechanism of toughening of the CFCCs"". Thus, different from the MMCs in which strong interfacial bonding is necessary, the interfacial strength of the CFCCs has to be controlled. As techniques for controlling the interfacial strength, it is also known that both a CVD-graphite coating and an h-BN coating are effective to induce the mechanism of toughening[1,2]. In the case, of the Si-C-O or Si-Ti-C-O fibers/glass or crystalline oxide matrix composites, it is reported that the formation of the in-situ graphite layer, which is also effective to increase the fracture toughness of the CFCCs, is often found during the fabrication process such as hot-pressing. The lower the crystallinity of the Si-C-O fibers, the higher is the tendency to form the in-situ graphite layer as found by the chemical reaction between the fibers and the glass matrices[3-12]. On the-other hand crystallized stoichiometric 'SiC fibers are attractive for high temperature service because of the higher phase stability compared to the Si¬C-O or Si-Ti-C-O fibers. However, in the previous, studies, the mechanical properties and the interfacial chemical reaction of the crystallized SiC fibers / glass matrix Composites have still been unknown. In this study, a polycrystalline 'sintered SiC fiber-reinforced MAS glass composite was fabricated. The mechanical properties and microstructure were then investigated. The slurry infiltration technique followed by hot-pressing was used to prepare the composites. The formation of the in-situ graphite layer and the relationship between microstructure and mechanical properties at room temperature were examined by the TEM observation of the fiber/matrix interface."

Jan 1, 2000

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By Guodong Lai, Shixing Wang, Lijuan Chu, Jinhui Peng, Zebiao Zhang

"The beneficiation of poor manganese ores containing phosphate gangue is very difficult by conventional processes, because of the similarities in the physico-chemical properties of the constituent minerals. The shaking table gravity concentration process and concentrated strong acid selective intensified leaching process were used for dephosphorisation of Yunnan manganese ore. The leaching process was effective. The effects of intensified leaching time, solid-liquid ratio and particle size were investigated. The relevant leaching factors were optimized as -0.125+0.088 mm particle size with 68% nitric acid for 24 h when using a solid-liquid ratio of 1:1 at room temperature and atmospheric pressure. Under these conditions, the P/Mn ratio was reduced from 0.0107 to 0.0056, and the grade of manganese was increased from 12.32% to 42.76%. The dissolution of manganese during leaching was negligible.IntroductionManganese and its compounds are widely used in the iron and steel industry as deoxidation and desulfurization agents and as alloying additives [1-2]. Because of the increase in demand, low grade refractory manganese ores are becoming a new source. Many Chinese manganese ores are high in phosphorus, which cannot be used directly for metallurgical purposes. This occurs because phosphorus enters into the metal phase during smelting and its presence sharply deteriorates the mechanical properties of the metal [3-4].Kanungo and Sant [3] investigated the dephosphorization of phosphorus-rich manganese ores by selective leaching with dilute hydrochloric acid. They observed that leaching with dilute hydrochloric acid (0.1-0.6M) could reduce the phosphorus contents to the specified limit of 0.12%. Ye [5] investigated dephosphorization of high-phosphorus manganese ore of the Huayuan type. Using high intensity magnetic separation, roasting and leaching with acid for dephosphorization, as used in the industry, a 40.15% manganese concentrate with a P/Mn ratio of 0.0037 was obtained. Yimin [6] investigated magnetic separation followed by inverse flotation of high-phosphorus manganese ore, and found that the P/Mn ratio could be reduced from 0.046 to 0.002."

Jan 1, 2012

By Qingwei Qin, Ping Xue, Guangqiang Li

Ausmelt furnace slag contains about 0.9% Cu (mass %). With increasing the amount of Ausmelt furnace slag, the recovery of copper from it will produce an enormous economic yield. The recovery of copper by floatation from slow cooled Ausmelt furnace slag was studied in this paper. The phases and composition of the slow cooled slag were analyzed. The factors which affected the copper recovery efficiency such as grinding fineness, pH value of flotation medium, different collectors and floating process were investigated. It was shown that the size distribution of the primary grinding and secondary grinding of middling were 75% for particles less than 0.074mm and 82% for particles less than 0.043mm respectively. The closedcircuit experimental results with butyl xanthate as collector in laboratory showed that the copper grade reached 16.11% and the recovery rate of copper reached 69.90% and the copper grade of tailings was only 0.2%.

Jan 1, 2015

By K. Morsi, S. K. Kassegne, K. S. Moon, A. Numula

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based manufacturing of macro, micro and possibly nano-scale features and shapes. CATS enables the selective sintering of powders by localizing current activation conditions through an electrically conducting small tip (either in the stationary or moving mode). This paper presents preliminary experimental results on the CATS of reactive mixtures of Ni/Al powder to form nickel aluminide intermetallics. Preliminary investigations on the effect of current on the reaction characteristics are discussed.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [1,2, 3,4,5,6]. The process boasts remarkable advantages which include ultra fast heating rates (hence by-passing low temperature non-densifying sintering mechanisms), considerably lower sintering temperatures and shorter sintering times than achieved in conventional sintering. The process is however limited to the generation of simple geometries on the macro-scale. Recently three of the authors conducted work on a novel process ""Current-activated tip-based sintering (CATS)"" [7], where electric current is passed through a conducting tip that is placed or allowed to travel over a powder bed/compact to locally sinter powders. lD, 2D and 3D micro-scale sintered shapes can be generated with the possibility of 3D rapid prototyping on the macro/micro or nano-scale. Although CA TS of single phase powders has been conducted, the CATS of reactive powders has not yet been investigated.The Ni-Al phase diagram contains five intermetallic compounds, AhNi, AhNh, AlNi, AhNi5 and NhAl. Out of these intermetallics, NiAl and NhAl have received the vast majority of scientific and industrial interest [8]. NhAl can be formed by reaction synthesis, where nickel and aluminum reactant powders are heated to a reaction ignition temperature at which the reactant powders are converted to the intended intermetallic product. The reaction is exothermic which gives rise to considerable compact self heating, thus instantaneously raising the compact temperature by several hundred degrees which facilitates sintering [8]. Applying and electric current locally would not only provide for a rapid local reactive sintering, but would generate a number of intriguing scientific investigations. For example, of interest would be, how would the reaction propagation and microstructural/phase evolution be affected by the temporal and spatial temperature and current distributions."

Jan 1, 2011

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By B. Nebreda, I. Vegas, R. Vigil, O. Rodríguez, M. I. Sánchez de Rojas, M. Frías, R. García, J. Urreta

"This paper shows the possibility of reutilize paper sludge waste as supplementary cementing material for the cement manufacture. This industrial waste consists essentially of a mixture of organic matter (30%) and inorganic compound, such as calcite and clay minerals. The raw paper sludge does not present pozzolanic properties, but once calcined at 650ºC during 2 hours, exhibits high pozzolanic activity, similar to silica fume at 28 days, as a consequence of the transformation of kaolinite into metakaolinite. Calcined paper sludge was used as partial Portland cement replacements of 0, 5, 10 and 20%. Enhancement in compressive strength was appreciably obtained for 10 and 20% substitution levels from 7 days on. Furthermore, calcined paper sludge slightly reduces the initial and final setting times of cement paste. Introduction Natural pozzolanic materials have been ordinary used in different aspects of construction, mainly for their influence on the microstructure and durability of blended cement matrixes [1, 2]. Due to the regulations of environmental protection, many researches are focusing on the possibility of obtaining pozzolanic materials from industrial wastes and not from natural materials (ceramic wastes, silica fume (SF), activated clays) [3–5]. One of the most used pozzolanic products is the metakaolin (MK) obtained from the activation of natural clay (kaolinite). The positive effect that MK has on blended cement performances [6,7] and also the influence that curing temperature and matrix nature have on the reaction kinetics and stability of hydrated phases produced during the pozzolanic reaction, according to the studies carried out by Frías et al. [8,9] are well known. However, there is a worldwide trend towards the use of recycled products in cement industry. In this line, some authors have reported an alternative way of obtaining MK from waste paper sludge [10-14]. The raw paper sludge (PS), once calcined under controlled conditions (700-800ºC), produces a MK with pozzolanic properties [15-20]. The present research is part of an experimental study about alternative source for MK from the Spanish paper recycling industry and its use as supplementary cementing material. This contribution pays special attention to the option of reducing activation temperature below 700ºC. This fact has a positive effect in reducing the energy consumption, as well as in reducing environmental impacts associated with decarbonation of calcite. The chemical and mineralogical characteristics of raw paper sludge and derived calcined product are described. In addition, the influence and behavior on blended cement properties (setting times and mechanical properties) are also discussed."

Jan 1, 2008

Roasting treatments were investigated to remove arsenic from a nickel concentrate. The main arsenic minerals and their proportions in the concentrate were niccolite (NiAs)-50%, gersdorffite (NiAsS)-40% and arsenopyrite (FeAsS)-10%. Thermal analysis showed that gersdorffite and niccolite began decomposing when heated above 640 and 830°C respectively. The maximum roasting temperature was limited by agglomeration of the concentrate above 900°C. A small vibrated bed reactor was used to investigate the effects of temperature and gas flowrate, the latter to sweep away evolved arsenic. At 900°C, 24% of the original arsenic remained in the concentrate. SEM examination of the calcine showed that the residual arsenic was associated with the calcium in the gangue minerals. Additions of sulphur (either as elemental sulphur or from pyrite) facilitated the decomposition of the arsenic-containing minerals, decreased reaction with calcium in the gangue and produced calcine containing 4-6% of the original arsenic. Treatment with chlorine during roasting was effective in reducing the arsenic content to similar levels. Generation of chlorine in the bed by sulphation of CaC12 also produced encouraging results. Arsenic, Nickel Concentrate, Roasting, Chlorine, Sulphur, Gersdorffite, Niccolite

Jan 1, 2005

By H. Kandemir

An experimental study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fe1-xS, Cu5FeS4, ZnS) is presented using a mesophilic strain of T. ferrooxidans. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate has been monitored as a function of leach time. Partially oxidized sulphide substrates have been characterized, at regular time intervals, by X-ray diffraction methods and extracellular organic compounds reporting into leach solution .have been identified by thin layer -chromatography.

Jan 1, 1985

By Ralph P. Hackl

Bacterial leaching of the Doe Run Company?s cobalt/nickel-containing copper concentrate at low pH (pH 1.0-1.2) and high redox potential (>750 mV vs. SHE) enabled the cobalt and nickel to be preferentially dissolved over copper and iron due to the rapid passivation of the chalcopyrite component. Selective leaching of the cobalt and nickel was achieved with a mesophilic culture comprised mainly of Leptospirillum-like bacteria and Acidithiobacillus thiooxidans. This finding led to the conception of a novel hydrometallurgical process for passivating chalcopyrite and recovering the cobalt and nickel. The bacterial leaching process was tested extensively at the bench and pilot plant scales during 1997-1998. A pilot plant containing four leaching stages processed 30-40 kg/day of chalcopyrite concentrate continuously for 87 days. The cobalt extraction ranged from 75% to 86% during 6- and 8-day retention times respectively, whereas the copper extraction was limited to about 9%

Jan 1, 2003

By Jogre A. S Tenório

he aim of the present investigation was to investigate technological features of the Fe-NbC dissolution in liquid Fe-C alloys. Fe-NbC is a Ferro-niobium alloy with 7%C, has a particle size smaller than 150 pm and its micro constituents are polygonal niobium carbides and an iron matrix. The obtained dissolution time was less than one-minute and the yields were in the range of 80-90% at 1873 K. In the Fe-NbC dissolution process, the dissolution occurs at first, and as a consequence the niobium carbides become free to dissolve. These carbides will dissolve until the melt reaches a saturation point. The non-dissolved carbides remain trapped in the liquid or will form a dross. The addition yields decreases when the niobium concentration reaches this limit value, that depends on the carbon concentration. These define a saturation curve.

Jan 1, 1994

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Wenliang Cao, Jidong Li, Mingjie Zhang, Yiyong Wang

In CaC12-CaF 2 System, we studied the electrode process and discharge mechanism of preparation of Al-Ca alloys by fused salt electrolysis with CaO as raw material. The change of back electromotive force after adding CaO was measured by continuous pulse oscillograph method and the discharge process mechanism was also investigated by cyclic voltammetry. The finial results indicate that back electromotive force decreases by 0.6V after CaO of 1 % is added and there was a peak of oxidation current ahead of the potential at which the negative chlorine ions precipitated. According to thermodynamic calculation, it was determined that current peak was caused by the CO2 produced by 0 2 - ionic discharge due to CaO addition.

Jan 1, 2014

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By T. A. George, David J. Sellmyer

"The concept of achieving a useful high-energy-product magnet through appropriate nanostructuring of known hard and soft phases has been tantalizing researchers since the idea was first proposed. The fabrication of exchange-coupled nanocomposite magnets faces several challenges including aligning the easy anisotropy axes of the hard-phase grains. Here we investigate experimentally two-phase nanostructures of hard Lio-ordered FePt and soft iron-rich/cc Fe(Pt). The Fe-Pt thin films were produced by epitaxial cosputtering onto MgO (001) single-crystal substrates which lead to strong (001) texturing. The measured hysteresis loops indicate nearly ideal exchange coupling. Excellent magnetic properties are obtained, with largest values of coercivity (51 kOe), saturation magnetization (1287 emu/ cm3, J, = 16.2 kG), and nominal maximum energy product (58 MGOe).1. IntroductionA key figure of merit for permanent magnets is the maximum energy product (BH)rrw.x. The achievable maximum energy product is determined by a magnet's saturation magnetization M, and its magnetic anisotropy. For example, it is well known that (BH)rrw.x :S 4n2M,2• In the past, record energy products have been the result of discovering new compounds with high values of magnetization and anisotropy. However, finding new compounds with better magnetic properties than the current record-holding magnet Nd2Fe14B has proven to be difficult. A different approach is to exploit the exchange coupling mechanism between known hard and soft magnetic phases to enhance the maximum energy product [1-5]. In such a composite system, high coercivity is achieved due to the anisotropy of the hard phase as well as a nanostructure which prohibits large-scale domain wall reversal mechanisms. Magnetization is enhanced by the soft phase and loop squareness results from texturing of the hard phase easy-axis as well as complete exchange coupling between the coexisting hard and soft grains."

Jan 1, 2012