Search Documents

By Robert De Saro, Willis Bateman, Ramesh Jain

A Vertical Floatation Melter (VFM) has been developed (sponsored by DOE) which simultaneously decoats and melts organic laden scrap in a single unit. Scrap aluminum is fed into the top of the VFM where it falls through a cone. Hot gases flow upwards through the cone, imposing a variable drag force on the scrap. Equilibrium is reached in which the scrap weight equals the drag force and the scrap becomes suspended. The gases strip off and vaporize the organics. Next, the scrap reaches a liquid state, taking on a more aerodynamic teardrop shape, allowing it to fall into a holding furnace. Heat transfer coefficients are 10 times higher than that of a conventional furnace, allowing rapid melting at a low gas temperature. Typical energy use is well under 2,324 joules/g (1,000 Btu/lbm) with a metal yield from 92 to 98%. This paper reports on the operation and data of a 453 kg/hr (1,000 pph) pilot-scale VFM.

Jan 1, 2000

By Line Hallgren

The fluid flow in the mold during up-hill teeming is of great importance for the quality of the cast ingot and therefore the quality of the final steel products. At the early stage of the filling of an up-hill teeming mold, steel enters, with high velocity, through the nozzle into the mold and the turbulence on the meniscus could lead to entrainment of mold flux. The entrained mold flux might subsequently end up as defects in the final product. It is therefore very important to get a mild and stable inlet flow in the entrance region of the mold. It has been acknowledged recently that swirling motion induced using a twist tape swirl blade, in the submerged entry nozzle is remarkably effective to control the fluid flow pattern in both the slab and billet type continuous casting molds, resulting in increased productivity and quality of the produced steel. From the above result, we propose, swirling flow generated through a swirl blade inserted into the entry nozzle, as a new method of reducing the deformation of the rising surface and the unevenness of the flow during filling of the up-hill teeming mold. The swirling blade has two features: (1) to generate a swirling flow in the entrance nozzle and (2) to suppress the uneven flow, generated/developed after flowing through the elbow. The effect of the use of a twist tape swirl blade was studied using both numerical calculations and physical modeling. Water modeling was used to assert the effect of the swirling blade on rectifying of tangential and axial velocities in the filling tube for the up-hill teeming and also to verify the results from the numerical calculations.

Jan 1, 2006

By Thomas Niehoff

"Oxyfuel combustion systems are state of the art for many melting operations. Airfuel systems have been stepwise modified to oxygen enrichment, oxygen lancing and oxyfuel. Every change of the melting process will have consequences with regards to emissions and energy usage. The uniqueness of many operations requires unique skills to resolve potential issues. This paper will give some examples of how airfuel systems can successfully be converted to oxyfuel.IntroductionOxyfuel technology – meaning the combustion of fossil fuels such as natural gas, oil or coal with technical oxygen instead of air for industrial melting or heating processes is widely used in many industries these days. Even though oxygen production, storage and handling has been state of the art for decades other opinions exist. Often oxyfuel is regarded with fear and potential hazards like: “Oxygen makes the process too hot.”, “Oxygen will melt away the refractory.”, Liquid oxygen is dangerous.”, “Oxygen will cause explosions.”, ……etc.Typically a more detailed discussion about a specific industrial process and how oxygen can be applied in a safe and economic way the seeming issues go away."

Jan 1, 2010

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By J. E. Jacoby

Scrap recycling has become an increasingly important source of metal units for the aluminum industry during the past 25 years. Aluminum scrap from the manufacture and recycling of cans, automobiles, buildings and other products has created an industry that melts these products and delivers the metal in molten or sow form to companies that make cast parts or fabricated products This rapidly developing recycling industry has contributed a large number of severe (Force 3) molten aluminum explosions (25) with associated fatalities (19) to the Aluminum Association data accumulated during the past nineteen years. The explosions that occurred in recyclers plants represent 17% of the total explosions, 33% of the Force 3 explosions and 37% of the fatalities reported. These explosions can be prevented! This paper will identify causes of these explosions and procedures that can be used to prevent them.

Jan 1, 2000

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Wang Haibei

China is the important country in terms of Ga, Ge reserves and products. These elements usually associate with lead and zinc ores such as in Fankou, Dachang and Lanping mines. Until now these metals could not be extracted from zinc residues effectively. The main reason is that it is difficult to separate zinc and iron. BGRIMM has carried out considerable research on this subject and some hydrometallurgical processes were developed. Zinc residues were pressure leached with a reducing agent such as zinc concentrates or SO2 at 110~130C. The final concentrate of H2SO4 was 30~50g/L. The metals such as Zn, Fe, Ga and Ge were dissolved into solution. In the leaching residue Pb and Ag could reach 20% and 2000g/t. The feed of solvent extraction was prepared from the leaching solution by pre-neutralization ? precipitation of Ga, Ge and acid dissolving. Then Ga and Ge were extracted by solvent extraction through P204 and G315 produced by BGRIMM. After stripping, metallic Ga was produced by electrowinning. GeO2 was produced by precipitation. The iron in raffinate was removed by the hematite process. The solution after removal of iron came back at the zinc neutral leaching stage. In 2003-2004, pilot tests were finished in BGRIMM in cooperation with Fankou Lead and Zinc Mine Ltd. And the extraction rate of Ga and Ge in the leaching stage was 94% and 83% respectively. The total recovery rate was 90% and 80%. It is estimated that the technology has a wide commercial use in the coming five years.

Jan 1, 2006

By Leszek Hoser

Polycrystalline oxide superconductors that have the perovskite structure, that are oxygen deficient, and that have compositions based. on the so-called. 1-2-3 (YBa2Cu3O7) compound, were investigated.. The materials exhibit a high critical transition to superconductivity at temperatures near 90oK. It was determined that maintaining the oxygen content within the correct range in connection with an appropriate amount of CU ions in the crystal lattice leads to high-critical temperature (Tc:) superconducting properties. High-Tc: superconductors with a critical temperature in the range of 100°K were developed. Further investigations, based. on the theoretical examinations of the origin of superconductivity, have been performed and are discussed..

Jan 1, 1989

By Shadia J. Ikhmayies

"Cadmium telluride (CdTe) is a very interesting material that has many applications. Thin films of p-type CdTe can be used as the absorber layer in the heterojunction CdS/CdTe thin film solar cells in which n-type cadmium sulfide (CdS) works as the window layer. A review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques was performed. The presence of defects and impurities such as oxygen and chlorine influence the PL spectrum. Copper and other dopants change the PL spectra and enhance the defects band. Chemical-heat treatment especially with CdCh is known to improve the quality of CdTe thin films because it decreases the Cd vacancies and quenches deep traps, so it enhances the PL signal. A discussion of chemical-heat treatment especially with CdCh, the effect of the ambient atmosphere, and that of the measuring temperature is performed.IntroductionCadmium telluride (CdTe) is a II-VI compound semiconductor that has a cubic zincblende (sphalerite) structure with a lattice constant of 0 A4~11]. Other than all of II -VI semiconductors, CdTe can be made both n- and p-type. But due to self compensation it is not easy to get p-type CdTe films [2]. Polycrystalline CdTe thin films are interesting because they have a lot of applications. Most of the problems associated with the use of these films are attributed to inhomogeneity, self-compensation, and the difficulty of forming a stable and lowresistivity ohmic contact [3]. CdTe technology has been established for a large number of applications, including solar cells, optical and nuclear detectors, and thermal- and radiationimaging devices [3]. At present, the highest demonstrated conversion efficiency for a CdTe based heterojunction (ID), with CdS as a window layer, is 16.5% [4, 5]. CdTe thin films can be prepared by different experimental techniques, such as thermal evaporation [l], electrochemical deposition (ED) [3], close-spaced sublimation (CSS) [3, 4, 6], physical vapor deposition (PVD) [3], chemical molecular beam deposition (CMBD) [7], and close space vapor transport (CSVT) [8].The objective of this paper is to make a review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques and discuss the factors that influence the PL spectra. The composition of the film is very interesting in determining its PL spectrum. Different kinds of defects, impurities and dopants have their finger prints in the PL spectrum. Deposition techniques and deposition parameters such as the deposition temperature and ambient atmosphere also have their influence. Heat and chemical treatments which are known to improve crystallization and reduce the defects change the PL spectrum."

Jan 1, 2013

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Kuiting Wang, Jinshan Liu, Ninglei Sun, Aiguo Dong, Yeda Lu

"Eliminating the environmental threat caused by waste effluent containing magnesium sulfate derived from the process of nickel laterite sulfuric acid leaching and subsequent nickel precipitation is always a focus in the metallurgy field. A new flowsheet whose procedures include vaporization, crystallization, two stages precipitation of magnesium, causticizing treatment of filtrate and ammonia recycle was investigated. Both the details of the flowsheet and its application are described in this article. It is confirmed to be an effective and economical method to prevent the pollution by the waste effluent, simultaneity, a series of magnesium products recovered during the process own good economic returns.IntroductionSulfuric acid leaching is the conventional procedure of extraction valuable metals from ores in hydrometallurgy field. During the process of nickel laterite sulfuric acid leaching, several metals, including Ni, Co, Al Mn, Fe, Mg etc., migrate into the leachate in the form of soluble metal sulfate. After subsequent procedure of purification, precipitation of Ni and Co and neutralization, an enormous stream of waste effluent which contains a concentration of approx. 15-40g/L Mg is exhausted. Such solution containing magnesium sulfate is toxic, which causes diarrhea for both human and animals. On the other hand, large amount of sulfate acid was consumed during the process of leaching by the compound of Mg, which increases cost of a hydro nickel plant.In arid areas, the waste effluent mentioned above is treated via evaporate pond owning large acreage, which needs not only the appropriate meteorologic condition, but occupies much land. In coastal areas, it is directly discharged to the sea, which probably deteriorates ecological system of offshore strip. The most widespread method to treat with the waste effluent is neutralization by lime cream, the residues of which containing magnesium hydroxide and gypsum are transported to residues pool. Neutralization is a simple process, but it never recycles the Mg and sulfate anion into new application, meanwhile, the residues are potential threat to the environment."

Jan 1, 2012

By Lei Wang, Xiancong Zhao, Hongxu Li, Lifeng Zhang

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Jan 1, 2015

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of Al2O3 or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10-5/°C of thermal expansion coefficient of QMIM can be obtained. The affecting mechanism of A1203 and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003

By Zviad Kovziridze

The problems related to the production and research of SiC-Si3N4 composite are presented. The technology of producing the protective casings for tips and thermocouples is developed. Optimum composition charge and technological parameters are defined. The results of casing testing at production plants are presented.

Jan 1, 2006

By Masatsugu Morimitsu, Tian Zhang

"This paper presents a novel anode for oxygen evolution in acidic aqueous solutions to produce non-ferrous metals by electrowinning. The method to prepare the anode was thermal decomposition of a precursor solution, and the obtained anode consisted of Ru02-based oxide catalytic layers formed on a titanium substrate, in which the catalytic layer contains nano-oxide particles as the active component. The oxygen evolution potential was lower than amorphous lr02-Ta20s coated titanium anodes so that the cell voltage of electrowinning was further reduced with the amorphous Ru02-based electrode.IntroductionElectrowinning (EW) is used to produce high purity of non-ferrous metals, and the primary metal production of copper, zinc, nickel, and cobalt by EW consumes huge electric energy worldwide, which tends to increase with increasing demand of such metals. The reduction of electric energy consumption is a significant issue for electrowinning industry, which means that the cell voltage reduction is needed to realize more energy-efficient EW processes. Another issue is also indicated from environmental perspectives; i.e., an improvement in EW plant environment by eliminating hazardous byproducts and wastes. Such byproducts and wastes include lead oxide, manganese oxide, and acid mist.We have been developing the anodes for energy-efficient and environmentally friendly electrowinning processes [ 1-11]. The development has been successfully done with the invention of the smart anode, MSA TM (Morimitsu Smart Anode) [ 1-5], which has low polarization for the main reaction and high polarization for the side reaction, in which the main reaction is oxygen or chlorine evolution, while the side reaction is the anodic deposition of each or both of lead oxide, manganese oxide, and cobalt oxide. The anode consists of a valve metal substrate coated with amorphous or less crystalline oxide catalytic layers. One of the typical examples of such oxides is amorphous lr02-Ta20s, and the substrate is normally titanium plate or mesh. The most important point of the oxide is that the amorphization or less crystallinity induce the increase in the active surface area only to the main reaction, not to the side reaction, thereby the polarization of the main reaction being reduced.In this paper, we present the smart anode consisting of RuO2-based catalyst formed on titanium substrates for oxygen evolution in electrowinning. The preparation, characterization, and polarization behaviors of the anodes are shown, and the cell voltage data for zinc or copper electrowinning using the anodes are also presented."

Jan 1, 2012

By Xiyun Yang

Magnetite was prepared by hydrogen reduction method. For a conversion to cobalt-modified magnetite, magnetite particles were suspended into a solution containing Co2+ and Fe2+ to precipitate a cobalt ferrite layer on the surface. pH value influences the particle composition directly, the desirable CoFe2O4 is obtained when pH value is 12. The coercivity increases with the increase of cobalt content, cobalt efficiency reaches a maximum value at cobalt content of 2.71wt%. With cobalt modification, magnetite particles have similar lattice constant and squareness ratio to that without cobalt modification. TEM and XPS analyses indicate that acicular morphology is retained during the coating process, the epitaxial growth layer consists of CoFe2O4and 0.3Co2O3CoFe2O4 at cobalt content of 2.71wt% and 5.03wt%, respectively.

Jan 1, 2006

By Jenifer S. Heath

Human health risk assessments can be used in mine permitting, and are frequently used to investigate areas of potential contamination and as a basis for remediation decision making. While some states and US Environmental Protection Agency (USEPA) Regions have their own guidance for the conduct of human health risk assessments, USEPA Headquarters guidance and the underlying science are changing and advancing rapidly. Even outside the US, USEPA guidance can affect risk assessment costs and conclusions, which in turn can affect cleanup costs or permitting options. This paper summarizes recent USEPA guidance and scientific evidence related to human health risk assessment for mining sites. This paper is designed for non-risk assessors, and so focuses on the potential applications and implications of the new guidance rather than the mathematical and theoretical details.

Jan 1, 1999

By Keith Cramer

As a leader in the development of metal extraction technology, Avecia continues to pioneer advancements for the processing of copper through leach, solvent extraction, and electrowinning of copper. From the initial patent of the second generation of oxime 5- nonylsalicylaldoxime in the 1970's; to the effective use of modifier technology; and development of computer assisted modeling programs, Avecia is driving SX technology to maximize extraction productivity. Keys to consider when advancing productivity are: 1) high quality, high performance products; 2) a responsive, partnering approach to technical service; and 3) tools to aid in the education of industry wide technical personnel with a view on continuous improvement. The focus of this paper is on the advancement of tools to aid in the education for optimization of processing copper through solvent extraction. One such tool is Avecia's own customized solvent extraction modeling program called MEUM. MEUM is currently used world wide to analyze plant operations, test ideas for improving operations, assist engineering companies in design, and to teach basic solvent extraction concepts. Recently MEUM has also been incorporated into a University setting. In the spring of 2000 Avecia worked with the University of Melbourne to integrate MEUM into their Mass Transport tutorial class. Students completed exercises to evaluate how operational changes affected a solvent extraction plant's performance. This paper introduces the basic functions of the program and discusses the successful implementation of MEUM into the University of Melbourne curriculum.

Jan 1, 2002

By Marcela C. Santini, Luiz A. Teixeira

"Surface conditioning (also referred as etching) of plastics prior to metallization is generally conducted with sulfuric I chromic acid solutions. Although these baths perform well technically, the presence of Cr (VI) imposes serious operating problems of an environmental nature. The present work reports ·the results of a study of surface conditioning o(ABS using solutions based. on sulfuric acid, with hydrogen peroxide and/or nitric acid, replacing chromic acid, as oxidants. Process performance was evaluated by SEM and by the uniformity and adherence of electroless nickel coatings applied on selected conditioned samples. The results showed that the evaluated types of solutions could be optimized to perform as well as the chromic-based baths, with a much superior environmental quality.IntroductionMetallization of plastics is normally undertaken for either decorative or functional purposes. Through metallization, the specific properties of plastics such as light weight, design flexibility, and low-cost of manufacturing are enhanced by the addition of properties usually associated with metals. These include reflectiveness, abrasion resistance, electrical conductivity, and a variety of decorative effects (1).The available processes that can be used for metallization of plastics are vacuum metallization or vapoµr deposition; indirect metallization and plating (1). Plating can be sub-divided into electroless plating and electroplating. In electroless plating, metal ions in aqueous solution are deposited on the .activated plastic surface by oxi-reduction reactions without the aid of an external electric potential, forming a thin metallic layer. This electroless deposited film has two functions: (a) it provides an electrically conductive substrate that allows further coating by electroplating; and (b) provides a secure bond between the plastic substrate and the electroplated layer (1,2). In case the electroless metallic part requires an additional layer for finishing purposes, or just an increase in thickness, the part can be additionally electroplated with a· variety of metals - in most cases those are copper, nickel or chromium (3)."

Jan 1, 2000