Search Documents

By Thomas Frost

In this time of market globalization, many industrial companies are including detailed arbitration clauses in their international contracts, in order to avoid the potential costs, delays, and uncertainties of litigation in foreign courts. Arbitration is less expensive and more flexible, procedurally, than court proceedings, and arbitral awards enjoy much greater international recognition than judgments of national courts. More than 134 countries have signed the 1958 United Nations Convention on the Recognition and Enforcement of Foreign Arbitral Awards, known as the "New York Convention", which facilitates the enforcement of arbitral awards internationally. There are several other similar arbitration conventions that provide for the enforcement of cross-border arbitral awards. Additionally, arbitral awards are not subject to appeal, whereas judgments of national courts are routinely subjected to a lengthy appeals process, and there are very few viable bases to challenge arbitral awards. This discussion will review key considerations in drafting arbitration clauses, including choice of law and choice of forum considerations; issues surrounding the selection of arbitrators; the discovery process; presentation of evidence; and enforcement of arbitral awards.

Jan 1, 2006

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of octamolybdate ion in aqueous solution appearing in the literature, a new method for the establishment of corresponding relation between Raman spectral pattern and chemical components of aqueous molybdate solution was put forward using spectroscopy measure and component analyses of saturated solution of ammonium octamolybdate hydrate known structure. It was found that the main characteristic of Raman spectral pattern of the saturated solution was described as the same ?double-peaks, hereinto a weak peak at the boundary? as some literature, but chemical components of the saturated solution were affirmed to be octamolybdate ion (Mo8O264-) and double protonated heptamolybdate ion (H2Mo7O244-), which were in equilibrium in aqueous solution each other. The authors propose that the pattern of the saturated solution can be regarded as the standard pattern of primiparous octamolybdate ion during acidified molybdate solution. It is satisfying that the standard pattern is applied to the identification of primiparous octamolybdate ion during acidified molybdate solution.

Jan 1, 2006

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Thomas Niehoff, Dave Stoffel

"Energy in the form of natural gas, oil and electricity is expensive and will continue to be a rare resource in the future. Recycling of metals, instead of primary production, is a logical and crucial step towards energy conservation. Energy consumption can be impacted by using advanced combustion systems for metals recycling. Air-fuel combustion has been the conventional method to melt and recycle metals. Global competitive pressures, “greenhouse” gas emissions, and high energy prices force melt shop operations to optimize energy usage and reduce overall operating costs. Oxy-fuel combustion and process technology can be applied to metal recycling operations to meet these objectives. Linde has converted several hundred furnaces from air-fuel to oxy-fuel technology and has extensive experience in optimizing the use of oxygen in furnaces. Additionally, Linde has the process knowledge necessary to avoid costly start-up issues that can accompany the transition to oxy-fuel technology. This paper will describe the benefits and potential issues for conversion to oxy-fuel.IntroductionThe furnace combustion system is the heart of a fossil fuel fired melting process and must be properly matched to the furnace to work as one cohesive unit. Furnaces vary widely in size, shape and features. Rotary furnaces are barrel-shaped and can be designed for tilting or nontilting operation. In a rotary furnace, the products of combustion create a single or double pass through the furnace prior to exiting. Reverberatory furnaces are box-shaped and can also be designed for tilting or non-tilting operation. Reverberatory furnaces are constructed of single or multiple chambers, with or without metal bath movement, and designed for continuous or batch processing. Different furnaces are used for different feedstock materials and products.Furnace combustion systems also vary in many ways. Combustion systems can be of air-fuel or oxy-fuel based technologies, or a combination of the two, resulting in an air-oxy-fuel system. Each of these types of systems has different combustion characteristics which can produce very different results. Here we will describe specific differences in melting processes and their associated energy requirements."

Jan 1, 2009

By Nicholas S. Lynn

"A new process has been developed to bioleach refractory gold ores to expose the precious metal values using Thiobacillus ferrooxidans bacteria.The ore is hosted in a limestone rock with secondary replacement of carbonaceous and pyritic minerals. Crushing, stacking, bioleaching, rinsing and neutralization have been completed in a 45-day total time cycle. The use of sulfuric acid operation, and concentrated Thiobacillus ferrooxidans population allows the short bioleaching cycle.The ore is then processed using conventional Carbon-In-Leach Cyanide recovery techniques.ABSTRACT ONLY"

Jan 1, 1997

By Berndt Moeller

Mercury-cell chlor-alkali production plants generate mercury contaminated wastewater streams from which mercury must be precipitated and filtered, resulting in a sludge containing 2% mercury (designated KI06) that cannot be landfilled in the United States without treatment. REMERC is a chemical treatment process used to recover 99% of the mercury from wastewater sludge generated at these plants. The process uses leaching to oxidize mercury compounds to mercuric chloride, washing and filtration to separate mercuric chloride from the treated sludge, and cementation to reduce the mercuric chloride to metallic mercury. Mercury not recovered in cementation is recycled to the wastewater process for precipitation and filtration. Treated sludge contains less than 260 ppm total mercury and 0.2 ppm TCLP, meeting the USEPA low mercury subcategory specifications that allow landfill disposal. REMERC uses readily available chemicals, is straightforward to control and inexpensive to operate, has no mercury emissions to air, and recovers metallic mercury. REMERC enabled significant cost savings including lower solids disposal costs, recovery and reuse of metallic mercury in the chlor-alkali process, and ability to treat non-wastewater sludge. No new EPA permits were required. REMERC was shown to be a viable process for recovery of metallic mercury from K106 designated sludge.

Jan 1, 2003

By Esperidiana A. B. Moura, Michelle Gomes, Cordelia M. F. Escanhoela, Francisco R. V. Diaz, Angel Ortiz, Rene R. Oliveira

"This work evaluates changes in morphological, mechanical and thermo-mechanical properties of electron-beam irradiated HDPE/nanoclay and HDPE/Piassava fiber/nanoclay. Material samples irradiated with 100 and 200 kGy using a 1.5 Me V electron beam accelerator (room temperature, presence of air) were submitted to tensile, flexural, and HDT tests. MFI, SEM and XRD analyses were carried out. Correlation between properties was discussed. Results showed that incorporation of piassava (Attalea funifera Mart) fiber and nanoclay, followed by irradiation represented significant gain in thermo-mechanical properties. Changes in surface morphology and reduction in MFI were observed. In conclusion, it may be claimed that the incorporation of piassava fiber in small size particles and nanoclay in the HDPE followed by electron-beam irradiation effectively improved the polymer properties and led to materials with superior properties suitable for several industrial applications.1. IntroductionIn recent years, the preference for using natural fibers instead of synthetic ones in polymer composites has been growing significantly. In Brazil, due to the great diversity of woody and fibrous plants of our forests, a vast potential of natural fibers is found, presenting good mechanical strength properties, chemical and biological stability, fire resistance, abrasion resistance, shear strength and lightness, among other which may contribute to the development of new materials for different applications such as automotive, aerospace, construction, food segment, cosmetics and others [ 1]."

Jan 1, 2013

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

By S. F. Cheng

Among the many extraordinary features of the rare earths are their magnetic and magnetoelastic properties. The rare earths, e.g. Tb, Dy, Nd, Sm, are known worldwide for their large magnetocrystalline anisotropy and magnetization, which has led to the importance of magnetic rare earths as vital ingredients of modem permanent magnets. In this paper, we focus on the strain dependence of these giant effects which gives rise to huge magnetostrictions, magnetomechanical couplings, and ?E effects. Magnetostrictions greater than 10-3 have been measured at temperatures as high as 500 K. At low temperatures magnetostrictions reaches -1%. ?E effects - 10. No other solid state material has matched these values. A proper balance of magnetic anisotropy and magnetostriction, plus a proper choice of crystal axes lead to alloys which can switch large quantities of energy between the internal (magnetic) and external (mechanical) states with the application of small triggering magnetic fields. In addition to the traditional use of these materials in transduction, they are particularly valuable for smart systems where reliability and robustness are needed such as active structure stiffening and active vibration control.

Jan 1, 1997

By Ivanildo Hespanhol

"DALYs are a measure of the health of a population or burden of disease due to a specific disease or risk factor. It evaluates the time lost because of disability or death from diseases compared with a long life free of disability in the absence of disease. DALYs are calculated as the sum of years of life lost by premature mortality (YLL) and years of healthy life lost in states of less than fully health, i.e., years lived with a disability (YDL), which are standardized by means of severity weights, thus: DALY=YLL+YLD.WHO has established for wastewater use in irrigation (1) the same reference level of health protection as established for drinking water quality (2), i.e., the additional burden of disease from consuming water irrigated food should not exceed 10-6 DALY(Disability-Adjusted Life Years) loss per person per year (pppy). This level of risk means that a single additional case of disease may occur in a population of 1 million, during a life time (70 years). In a individual basis is equivalent to the occurrence of a mild disease during about 31,5 seconds.Such a restrictive risk is almost impossible to be attained in most developing countries which may not be able to afford the cost of wastewater treatment and of other protective measures, even for restrict irrigation.This paper presents proposals to adapt the reference level of risk to local technical, cultural, economical and social conditions of developing countries on the basis of a risk benefit approach."

Jan 1, 2008

By Kai Tang, Casper van der Eijk

Natural gas has been used as reductant in the production of iron for several decades. Recently, the use of natural gas as reductant for other metals has been drawing attention because of the low price of natural gas, as well as the reduction of CO2 emissions compared to the use of coke and coal. In this work, the reduction of a mixture of Ti- and Ni-oxides by natural gas has been studied. Within the Ni-Ti system, the intermetallic compound Ni3Ti is thermodynamically the most stable one. Therefore, powders of Ni-oxide and Ti-oxides were mixed in an atomic ratio of three to one and subsequently pelletized. Reduction was performed in a TGA furnace at constant temperature with varying reducing gas atmospheres. In a natural gas containing atmosphere, the Ni-oxide was easily reduced to metallic nickel while the Ti was reduced to Ti-oxycarbides or Ti-oxynitride when nitrogen was present. Depending on the process parameters, several percent of Ti was dissolved in the nickel-based solid phase.

Jan 1, 2014

By Bruno Lebon, Koulis Pericleous, Georgi Djambazov, Mayur Patel

"High speed compressible jets are used in a number of steel-making applications. In the case of the BOF, a compressible oxygen jet reacts with a carbon-rich iron bath to reduce carbon levels and produce steel. The intensity of the process is governed by the speed of the jet and by the size and shape of the depression created in the metal and slag by the force of the jet, i.e. by the corresponding free surface. This is a difficult CFD problem, since there are compressible and incompressible regions in the flow domain, which need to be handled differently in a finite-volume (FV) pressure-correction scheme. Also, standard turbulence models do not account for compressibility, or the large difference in density between the cold oxygen jet and the hot reacting surroundings. Corrections are introduced to the k-E model to remedy this deficiency and the results are validated against experimental data. The compressible/incompressible boundary is handled through a transition region, based on Mach number.IntroductionThe deformation of a free surface by a compressible high speed jet is of paramount engineering interest, particularly for understanding the physical processes within a Basic Oxygen Furnace (BOF). In a BOF, a supersonic oxygen jet impinges on a molten iron surface, thereby creating a cavity. Oxygen penetrates the bath and removes carbon, resulting in low carbon steel [1].The challenges in modelling such a process lie in coupling a solution domain with distinct compressible and incompressible regions and in dealing with large density differences between the modelled gas and liquid. The modelling of compressibility within the jet is crucial, since the correct velocity profile in the jet is required to determine the cavity depth with accuracy."

Jan 1, 2012

By Susumu Okabe

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace for settling the slag/matte mixture formed in the smelting furnace. In order to improve the separation of slag and matte and to minimize power consumption, the design and the operating conditions of the electric furnace should be optimized. As the first step, numerical heat and fluid flow analysis of the melts was carried out based on the distribution of current density and Joule?'s heat obtained by the electric field calculation. For these calculations, 3-D body fitted coordinate system and a finite volume method were applied. Using the developed numerical model, the flow pattern analysis by pulse input of a tracer element was simulated. It was found that a strong thermal convection of the molten slag exists around the electrodes due to the concentrated Joule's heat generation in a small area just under the electrodes, and this strongly affects the flow pattern in the furnace. The calculation results were compared with the data obtained from 'a plant test.

Jan 1, 1998

By Brady Butler

Many high capacity metal hydrides exhibit a high degree of stability in the hydrogenated state. This stability leads to a number of significant design problems with regard to the low temperature kinetics and thermodynamics of dehydrogenation. Nanometric metal hydride materials provide a promising route for increasing the reaction kinetics while altering the thermodynamic stability of the material. The use of nanometric metal hydride materials for hydrogen storage has largely been absent because of the difficulties associated with the synthesis of these materials. In this paper, research results on the synthesis of lithium based metal hydrides by vapor phase reactions are presented. The lithium based compounds that have been made in our lab include nanosized powders of metallic Li, Li₃N, LiNH₂ and LiH. The vapor phase process has also been used to custom engineer Li-based materials with other alloying elements or doping elements. The dependence of the characteristics of these materials on synthesis process parameters is studied. The effects of nanoscaled particle sizes on the kinetics of dehydrogenation and hydrogenation reactions are also explored.

Jan 1, 2006

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By Finn Olesen, Melina Garcia, Mark William Kennedy

"Furnace resistance is a function of the complex interrelationship between many factors including: operating practice, slag conductivity, temperature, power intensity, and geometry (electrode shape, diameter, spacing, immersion, slag depth, etc.).Accurate prediction of resistance is critical for success of the overall furnace design. The sizing of electrodes, columns, bus-bars, and transformers are all impacted. Estimation of minimum and maximum resistance or maximum operational current, as well as the maximum operating voltage are of fundamental importance.Various mathematical tools have been developed to assist designers with the selection of furnace dimensions and the prediction of resistance. Elkem found the methods of Downing and Urban 1965 and Westly 1975, to be particularly useful.In the current paper, comparisons are drawn between data from spent aluminum pot lining (SPL) demonstration testing at Elkem Bjolvefossen and predictions based on these classical tools and 3D finite element modeling (FEM) with COMSOL.®"

Jan 1, 2012

By Norihiro Murayama

The hydrothermal syntheses of zeolites from coal fly ash were carried out using NaOH and KOH as an alkali source. The cation exchange capacity (CEC) and the ion exchange selectivity were investigated for the zeolites synthesized by a hydrothermal treatment. The effective usage of the zeolite as a cation exchanger was considered from the viewpoint of engineering. Zeolite P, HS (hydroxysodalite) and K-CHA (potassium-chabazite) are mainly formed as zeolite species in NaOH or KOH solution at 393K. The zeolite P and K-CHA have a large exchange capacity as a cation exchanger. The cation exchange isotherms of various monovalent and divalent cations with various zeolites are investigated. The order of selectivity of the zeolites is as follows, NH4+> K+> Li+.For the divalent cation, the largest removal amount is obtained for Pb2+ in the low equilibrium concentrations below 0.2mmol/dm3, and almost perfect removal can be achieved for Pd2+. The order of selectivity of zeolites in low concentration is expressed in the following order; Pb2+> Co2+> Cd2+> Ca2+> Mg2+> Ni2+. Ii is considered the zeolites obtained from coal fly ash can be used as an excellent cation exchanger.

Jan 1, 2006

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989