Search Documents

By Daniel C. McLean

Extraction data for Cu, Zn and Fe were obtained from 4.5" and 10" columns using massive sulfide ore and natural acid mine water. The purpose was to determine if recycling of solution through the column would produce leach liquors of 4 g/l Cu and Zn at extraction rates of 1 g/l per pass at typical flow rates of 0.002 to 0.006 gpm/sq.ft. Test results exceeded expectations. Cu and Zn concentrations of 4 g/l were obtrained within 4 to 6 cycles. Concentrations greater than 6 g/l Cu and 8 g/l Zn were reached within 10 cycles. Concentrations of greater than 40 g/l of Fe and free sulfuric acid were obtained with no decrease in biological activity being observed. No reagents were used.

Jan 1, 1995

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By G. Archer

ASARCO, a large and diverse producer of nonferrous metals, is involved primarily in the smelting and refining of lead and copper. Lead-antimony alloys, antimony trioxide, bismuth, cadmium oxide, selenium, tellurium, silver and gold are among products which result from processing by-products of smelting and refining. The complex mixture of concentrates at some smelters and the high impurity loads at some refineries result in various drosses, sludges, dusts and slags. In this paper, the complex interplant and intraplant transfer of by-products is addressed. These by-products result in an exchange of metals between the lead circuit and the copper circuit. Examples of the transfer of by-products and the prospects for the recycle of valuable products from wastes generated by customers and unrelated processors are also discussed.

Jan 1, 1992

By Jun Iwai, Osamu Takai, Yasushi Inoue, Hiroyuki Sugimura

"Infrared reflection absorption measurement was performed during plasma-enhanced chemical vapor deposition of silicon dioxide films at room temperature. Hydrocarbon contaminants adsorbed onto growing film surface are oxidized by oxygen radicals in plasma resulting functional groups which include C=O and C-O bondings. These groups exist only near the surface and are hydrolyzed rapidly after exposure to air.IntroductionRecently low-temperature silicon dioxide (SiO2) deposition has been in a growing industrial demand in pa1ticular, polymelic substrates such as polycarbonate and polyethylene telephthalate, which have poor heat resistance, need low process temperature (near room temperature) in coating of SiO2 which is a suitable material to improve optical and mechanical properties of polymenc products. Plasma enhanced chemical vapor deposition (PECVD) using organosilicon reactants is one of the most promising technique for lowering process temperature, so that it has been extensively studied1-12. In the present; however, hydrocarbon contaminants and a plenty of Si-OH termination in Si-O-Si networks tend to exist in the films, which degrade mechanical, optical and electrical properties of the films. It is necessary to understand the deposition mechanism at, low temperature in order to solve the problems. We have studied the low-temperature PECVD of Si02 by spectroscopic diagnosing techniques such as optical emission and mass analysis6-7, 11- 12Infrared reflection absorption spectroscopy (IR-RAS) has been a well-established technique for characterization of thin films on metals as· well as on semiconductors and insulators13-17. In this paper, we report on' the surface reaction of room-temperature PECVD of Si02by using in situ IR-RAS."

Jan 1, 2000

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By Reinhard F. Dobner

After a short introduction about the HK's secondary smelter process and explanations concerning the anodes produced the regulation and buffering of bleed will be described and the principles of technology for processing of bleed will be presented. Modernization aspects, especially installation equipment, and the different types of evaporators used will be described in detail. Besides, experience made with acid-resistant materials - stainless steel, enamel, plastics - will be reported. Environmental aspects such as water and air pollution will be outlined briefly and in conclusion the quality of products obtained as well as quality control will be presented.

Jan 1, 1997

By R. L. Miller

Oil -bearing metal sulfide sludges produced in treatment of an industrial wastewater, which includes plating wastes, have yielded to treatment by electrooxidation and hydrogen peroxide processes. The oxidation can be controlled to be mild enough to avoid decomposition of the organic phase while oxidizing the sulfides to sulfates. The pH is controlled to near neutral conditions where iron, aluminum and chromium(II1) precipitate as hydrous oxides. Other metals, such as lead and barium, may be present as sulfate precipitates with limited solubility, while metals such as nickel and cadmium would be present as complexed ions in a sulfate solution. The oxidations were found to proceed smoothly, without vigorous reaction; heat liberation was minimal.

Jan 1, 1992

By Marshall Khan

The Goodfellow Expert Furnace System Optimization Process (Goodfellow EFSOP?) is a proprietary process that uses real-time and continuous off-gas analysis, along with process monitoring to optimize the operation of electric arc furnaces (EAF) for steelmaking. With the exception of off-gas composition, dynamic process measurements within the EAF are not possible due to the harsh operating environment. The Goodfellow EFSOP? system provides a dynamic indication of the operating conditions within the EAF. Continuous measurement of furnace off-gas composition, along with other furnace operating parameters is used to elucidate the fate of chemical energy usage within the EAF including: the evolution of carbon from the molten steel bath; the in-leakage of air into the furnace; the extent of combustion above the molten steel bath and the occurrence of dangerous water-leaks from the furnace cooling system. The ability to measure the process reliably and continuously enables Techint Goodfellow Technologies Inc (TGTI) to implement dynamic process control of combustion within the electric arc furnace and to optimize the overall operation through adjustments to the EAF process based on off-gas measurement. This paper discusses the methodology and results achieved from several recent Goodfellow EFSOP? installations in South East Asia.

Jan 1, 2006

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade.

Jan 1, 2006

By Pierre-François Bareel

EU legislation imposes ambitious recycling targets for various consumer goods. End-of-Life Vehicles (ELVs), scrap iron and various proportions of Waste Electrical and Electronic Equipment (WEEE) are processed by shredding plants which recover most of the metals but produce Shredder Residues (SR) which are landfilled. They represent 20 to 25 wt.% of the shredder input. Energy issues for the coarse fraction of SR are now largely studied. However, below 2 mm, the calorific value falls off drastically. These Fine Shredder Residues (FSR) represent up to 55 wt.% of the total SR. To meet European objectives other alternatives to landfilling must be considered for the FSR. The present paper describes a study carried out to characterise the FSR and investigates ways to process them and produce marketable products. Applying Gy's theory, a sampling procedure was conducted over two years to statistically quantify the variability of the physical and chemical properties of FSR produced by a Belgian post-shredding treatment plant. Macroscopic characterisation has led to the identification of four material categories which could be separated according to their physical properties: ferrous metals (more or less oxidised), non-ferrous metals, an organic fraction (plastics, rubber, textiles, foams, wood) and a minerals fraction (glass, ceramic, concrete). The entrainment of small metallic particles within the pores of organic fragments will affect the quality of the separations.

Jan 1, 2006

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

By Larry M. Southwick

Pneumatic converting (Bessemerizing) of iron revolutionized the steel industry. Bessemerizing of copper (conversion of copper sulfide matte to copper metal) was proposed at almost the same time, but it was slow in being accepted. The differences between iron and copper converting were great and technical problems were substantial. It took 25 years for the process to become viable and another 25 years before a truly economical solution was found. A major economical and productivity problem was the short life for converter refractory linings. The first converters had acid (silica) linings, which were quickly consumed since silica was a flux for the process. Converters had to be relined at least once per day, a laboriously expensive manual process with only the most rudimentary mechanical aids available to assist. The industry was revolutionized almost overnight when finally a viable basic (magnesite) lining was developed. This lasted 100's of days versus less than one, leading to converters that were easier to operate and which handled larger charges. This change occurred after W.H. Peirce and E.A.C. Smith, with support from the Guggenheim interests, successfully operated a basic lined converter in a copper refinery in Baltimore. While Peirce and Smith are generally given credit for the development and explosive acceptance of this idea, a Pittsburgh industrialist, Ralph M. Baggaley, working in an independent smelter in Butte, Montana, successfully built and operated a basic lined converter four years before they did. In fact, the early support for Peirce and Smith likely occurred because Guggenheim's staff were encouraged after thoroughly examining Baggaley on his earlier successes. The questions of technology primacy between Baggaley and Peirce/Smith are ironically similar to those between Wm. Kelly and Bessemer in converting iron to steel. This paper will review what Baggaley (and other early researchers) accomplished, examine why he (or they) did not receive credit equal to Peirce and Smith and explore what his (their) place should be in the development of successful basic linings. More suspects than a Victorian Whodunit.

Jan 1, 1999

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By R. K. Hill

The Hidalgo Smelter successfully reduced operating costs by 25% compared to the previous two years through a focused holistic approach to development of its entire workforce. The first phase involved basic team training skills for natural work teams. The second phase provided leadership training via breakthrough education to 40 of the smelter leader-both hourly and salaried. The third phase stretched out the teams training to include rewards for performance that resulted in hourly teams converting to salaried status-part of a company wide initiative. The fourth phase saw 1998 become the "Year of Safe Cost Reduction" where 7 breakthrough projects focused on different areas of expenditure. Implementation of lean manufacturing as a tool for teams to truly get their arms around what they controlled, introduced accountability and responsibility for operating results at the team level. This will allow the release of experienced supervisors from this role, to a pool of technical expertise, where our future breakthroughs will be designed and implemented.

Jan 1, 1999

By Robin M. Forbes. Jones, Suhas V. Patankar, Ramesh S. Minisandram, Jr. Carter, Kanchan M. Kelkar

"The nucleated casting process currently under development has the potential for production of Ni-base superalloy preforms that possess superior microstructure to product made by conventional casting processes, primarily for gas turbine applications. In this process, electroslag remelted (ESR) clean (i.e., free of ceramic inclusions) molten metal is conveyed via a watercooled copper Cold-walled Induction Guide (CIG) to a gas atomizer. The spray of clean metal droplets is then directly cast into a water-cooled crucible for ingot production. The microstructure of the resulting ingot preform evolves within the length scale of the individual droplets and is a function of the thermal state of the incoming metal droplets. This, in turn, depends on particle size, flight time and heat exchange with the gas phase.In the present study, computational models is developed for the analysis of the flow and heat transfer in the gas-metal spray system under axisymmetric and steady-state conditions. The gasphase flow is analyzed using an Eulerian framework and turbulent mixing within the gas phase is modeled using the two-equation k-e model. The dynamics of the metal particles is analyzed using a Lagrangian framework that involves calculation of the trajectories of the metal droplets. A two-way coupling is considered whereby the transport and heat transfer in the gas and the metal phases influence each other.The analysis is developed at two levels. The spray model performs a detailed calculation of the spray dynamics in the vicinity of the spray and is intended for predicting the temperature and mass flux distributions of the metal spray depositing into the mold. The chamber model enables prediction of gas flow and motion of metal particles in the entire spray chamber."

Jan 1, 2004

By Yue Tian, Shengqian Wang, Lifeng Zhang

This paper is to discuss the removal of non-metallic inclusions from molten steel using a high frequency magnetic field. In experiments, a certain amount of aluminum was added to the molten steel in a crucible to generate aluminum inclusions. A layer of aluminum clusters were observed close to the wall of the crucible after the electromagnetic (EM) field was imposed. Three dimensional EM field and fluid flow simulation were performed and showed that over 91% inclusions transported to the skin depth (2.31 mm) of the molten steel. The calculation of inclusion removal agreed well with the experimental observation. The separation mechanisms of inclusions from the molten steel by the high frequency EM field were discussed.

Jan 1, 2014

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997

By G. Achurra

The products of the smelting of copper concentrates in an El Teniente Converter (CT) are a high grade matte, analyzing 74-76% Cu; and a highly oxidized slag, typically containing 15-20% Fe3O4 and 4-10% Cu. The El Teniente Division of CODELCO¬CHILE has developed a slag reduction-cleaning process, that is practised in a tilting, horizontal furnace, to recover copper from these slags. The El Teniente slag cleaning process has been successfully implemented at the El Teniente Caletones smelter and various other smelters in Chile: Today, eight such slag cleaning furnaces, each with a capacity of 800-1000 tonnes/day, are in operation in Chile. This paper discusses basic laboratory research and industrial tests that led to substantial reductions in the slag cleaning cycle time and the specific consumption of fuel and reductants. Simultaneously, the slag cleaning off-gas quality was improved. Based on the experimental results, recommendations were made to improve the practice of the El Teniente slag cleaning process. The recommended modifications have been fully implemented at the Caletones smelter.

Jan 1, 1999

By Kazuaki Mita

There are various intermetallic compounds in the Zn-Fe system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic properties of intermetallics was then evaluated through measured intensity.

Jan 1, 1999

By A. J. Davidson

A novel sensor is described for the measurement of the copper content of copper matte. Due to the high copper concentrations found in matte, potentiometric sensors are not sufficiently sensitive. A highly sensitive sensor has been developed based on a modification of the amperometric technique using a copper ion conductor, Cusicon. The results correlate closely with the theoretical predictions.

Jan 1, 1998