Search Documents

By V. Bhagavathy

This paper describes a method for the determination of traces of rare earths using energy dispersive x-ray fluorescence spectrometry (EDXRF) after preconcentration of their oxine complexes onto activated carbon. Various parameters that influence adsorptive preconcentration of rare earths onto activated carbon viz. pH, amounts of activated carbon and oxine, time of stirring and aqueous phase volume were systematically studied. A numerical method based on simple least square procedure using fifth order polynomial with 25 consecutive values was developed for smoothing and differentiation of EDXRF data which was previously digitized and averaged. First order derivative EDXRF in conjunction with adsorptive preconcentration on activated carbon enables to determine as low as 10 ppb of each of individual rare earth elements.

Jan 1, 1989

By M. Benavides

An experimental study is carried out With sulphide ore obtained from Bailadores-Venezuela as well as artificial concentrates. Concentrates of the minerals from froth flotation are fused to study equilibrium between the matte and slag phases. The first part of the work deals with obtaining a concentrate by flotation experiments with collective and selective reagents, with acceptable metallurgical recovery, studying the influence of different parameters in the process. The second part gives the results of the experimental investigation. on thermodynamic equilibrium in smelting which facilitates knowledge of the elemental processes, giving bases for the possibilities of reducing the loss of metal in slag.

Jan 1, 1983

By Elizabeth M. Ho

Oxidants are added in uranium leaching in acid media to convert iron(II) in solution to iron(III). Iron(III) has an important role in the leaching of uranium by acting as an electron transfer agent for the oxidation of uranium(IV) to uranium(VI). The oxidation of iron(II) to iron(III) in sulfate solutions using sulfur dioxide/oxygen (SO2/O2) was carried out under typical uranium leaching conditions (pH 1-2, 20-50°C) to confirm literature trends and this work was then extended to the use of SO2/O2 in the leaching of uranium ore. The oxidation rate was found to be dependent on the initial SO2/O2 volumetric ratio and the oxygen mass transfer rate, but was independent of the initial iron(III) concentration above about 200 ppm at pH 2. The presence of 55 ppm organic extractant (Alamine 336) decreased the reaction rate. The oxygen mass transfer coefficient (kLa) for the mixing tank system was measured and was found to decrease with increasing solids density in a 1 g L-1 MgSO4.7H2O solution.

Jan 1, 2003

By Liping Li

A comprehensive three-dimensional two-phase mathematical model was developed to represent a channel type reactor with intense bottom gas agitation. Tracer dispersion and particle tracing methods were used to conduct the analysis based on the solution of the Navier-Stokes equations. Different operational parameters, such is gas volume flow rate. bubbler separation aspect ratios and liquid Input flow rates, were investigated for the purpose of reactor optimization. The numerical calculations were compared with experimental results obtained at the University of Missouri and a good general agreement was observed. Relatively low longitudinal mixing was observed characterizing the system as a "plug-flow" type reactor, in contrast to the intense vertical mixing, under the conditions investigated. Some general mixing characteristics are also discussed In connection to the behavior of other metallurgical reactors.

Jan 1, 1996

By Fernanda Margarido

Recovery of metals contained in the electrode materials of batteries was studied considering an integrated recycling process constituted by physical and chemical operations. The physical treatment included the shredding of the spent batteries, followed by a wet sieving operation of the fragmented material. The physical behavior of Ni-Cd and Zn-Mn based (alkaline and saline) system batteries was studied and compared. In that sense, shredding operation was performed and the sieving of shredded fractions was accomplished to evaluate the efficiency of the separation of electrodes and scrap. For Ni-Cd batteries the loss of electrode material with the supra fraction (scrap) after the shredding operation was lesser than the Zn-Mn batteries. Especially for saline-type batteries, the electrode attached to the scrap was substantial leading to important losses. This difference can be explained by the composition of the case materials and the internal physical constitution of the electrodes. The wet sieving studies carried out allowed optimizing the separation of the electrode fine fractions from the scrap materials through the analysis of selectivity Cd/Fe or Zn/Fe. For Ni-Cd batteries, maximum selectivity was achieved for the granulometry of 1.4 mm, while for alkaline and saline systems best selectivity were obtained at 2.8 mm and 5.6 mm, respectively. This process allowed the recovery of about 70% of electrodes for Ni-Cd and alkaline systems, and 50% for saline batteries, with less than 5% of scrap as contaminant. This physical step can be considered as a pre-treatment of this type of waste material envisaging its valorization by chemical treatment, as improves the concentration of the elements of interest and decreases the iron content.

Jan 1, 2006

By Etsuro Shibata

For the treatment of huge amounts of the sulfur which is from the earth by both natural and man-made activities, a harmonized sulfur cycle was presented. The man-made sulfur cycle which includes sulfur circulation from oil, coal and ore was analyzed in detail based on the recent world sulfur trend. Then the man-made cycle was compared with the natural sulfur evolution such as volcano. Finally, the harmony in both natural and man-made sulfur cycles was discussed.

Jan 1, 2006

By R. E. Molnar

A number of flowsheets have been designed and operated, or are currently being considered, to extract copper from leach solutions having much more copper than the 4 g/L levels typically found in heap leach liquors. Dealing with these solutions has required that the envelope for ?normal? copper solvent extraction be pushed beyond the usually considered limits. Others have published information on flowsheets to recover copper from leach liquors containing over 25 g/L copper. Secondary solvent extraction circuits are often required to attain satisfactory overall recoveries. This paper reviews some of the issues faced in three pilot plant circuits that were operated by SGS Lakefield Research to produce cathode copper from solutions containing 8 to 20 g/L Cu. The primary objective was to maximize copper extraction using one solvent extraction circuit. The role of feed acidity and the disposition of impurities such as iron and chloride are considered. The challenges of running short SX piloting campaigns are discussed.

Jan 1, 2003

By E. M. Alcântara

This paper describes some aspects about the relationship between copper electrorefining addition reagents and the hydrogen in the cathode. The conditions of electrorefining were studied by factorial design methods. The advantages of this technique are reduction in the number of tests, well organized experiments; improvement in productivity and reliability of results. The dosage of the two main addition agents, glue and thiourea, were varied simultaneously and compared with the hydrogen content in the cathode. The influence of these factors, as well their interactions were analyzed by statistical methods denominated ANOVA (Analysis of Variance). The increase of thiourea quantities, within of levels studied, influenced significantly at 95% confidence in the hydrogen content in copper cathode.

Jan 1, 1999

By Hans Hein

In its early stage of copper solvent extraction development, SX plants were designed in a series configuration and gradually the copper industry reduced staging and trains for keeping capital investments reasonably low. At a later date of its development, series parallel configuration was applied in some copper SX plants, particularly for increasing copper production at low copper tenor in pregnant leach solution. A gap between series and series parallel configuration had been observed for years. Conventional SX plants in series configuration frequently do not have the flexibility for maintaining designed or expected production level, whenever copper concentrations in pregnant leach solutions are getting low, whereas series parallel flow schemes almost require to double SX feed flows for achieving optimum results. A combined SX configuration breaks the gap and its application potentials are explained.

Jan 1, 2003

By V. M. Mukhin

Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose. In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a full-scale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon. During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.). Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.

Jan 1, 2006

By H. Aminian

Copper electrowinning (EW) is an important process in connection with the solvent extraction to produce pure and marketable copper cathodes. A phenomenological model was developed to simulate the copper electrowinning process. The simulator is used to predict the operation of the Mines Gaspe pilot plant electrowinning cells put in operation in 1996. Results confirm the potential of the simulator that would subsequently be used for student training, process optimization and assessing the performances of control strategies.

Jan 1, 1999

By N. Lohja

Metallurgical industries are generally big producers of solid residues of various kinds. In contrast with the past where environmental sensibilities were not so elevated and the accumulated mass of these residues were not considerable, these days the solid residues are everywhere scrutinized among others in term of their harmful environmental impact and as possible materials for valuable elements extraction or secondary utilisation. As a case study, the present paper gives an overview of the solid residues discharged by the metallurgical industry in Albania for the last tens of years. The results of two monitoring study on the solid residues of copper, iron and ferrochromium producing industries are also summarized. The first deals with the origin, quantities and chemical composition of these residues and the second one with the impact of harmful ingredients of these residues in the environment. Some methods for the processing of these solid residues are also proposed in order to ensure a clean environment and to make not just possible but also economically viable their secondary utilisation. This work is part of a bigger cooperation project among local institutions and foreign expert companies such as Flogen Technologies Inc and other in various countries that will not only monitor the situation but will also develop appropriate technologies for treatment of these specific residues.

Jan 1, 2006

By Simon Lekakh

Direct reduction of Cu,Ni,W,VandMo oxides from various industrial wastes the melting of iron and steel in different furnaces was studied by thermodynamic computation and experimental methods. Thermodynamics was used to compute the final partition of the alloying additions between iron-carbon melts and oxides contained in the slag. It was shown that the sequence of the reduction reactions depended on the melt composition as well as temperature. Kinetic factors limited recovery in induction melting, while experimentally measured final partition coefficients were close to equilibrium during EAF melting. The possibility of the partial substitution of expensive ferroalloys, by different industrial wastes containing nonferrous oxides, was evaluated in foundry and mini-mill conditions.

Jan 1, 2006

By Natasa Mitevska

The distribution coefficients of Ag, As, Au, Bi, Co, Cu, Ni, Pb, Sb, Se, Te, and Zn between copper matte and slag from the reverb furnace No.2 at the Copper Smelter and Refinery, RTB BOR (Yugoslavia), are presented in this paper. The influence of the matte grade on the minor elements distribution coefficients between copper matte and slag is analyzed. The minor elements distribution in the slag phase along the slag melt depth and the furnace length is also determined.

Jan 1, 2002

By David A. Army

Many times, the maintenance professionals have been involved in changes to processes or systems. Often they rely on seat of the pants knowledge to determine whether or not they were successful. More often than not, once our attention has been turned to other endeavors, the initiative has floundered. This paper will describe those measures that can be most effectively used to track and manage the success of implementing an improved Work Management System. However, not only will the paper discuss traditional work indicators, it will also explain how to establish the behaviors in the work place that will ultimately ensure successful implementation. Combined with the discussion on indicators will be a discussion on how to tie them to bottom line results and display them in the form of a scorecard. Actual results will be discussed.

Jan 1, 2006

By Kurt Westerlund

The design of the economically most profitable and technically most feasible smelter process gas handing and treatment as an integrated part of the total metallurgical process is discussed and exemplified, with alternative flow sheets including material and energy balances, investment and operating costs. Retrofitting and de-bottlenecking of existing gas handling lines wil1 be described and exemplified. Methods of increasing total gas handling line availability will be described.

Jan 1, 1992

By María Cristina Ruiz

In the processing of copper concentrates by the conventional smelting-converting technology, complying with the increasingly severity of environmental legislation in some countries has become difficult, mainly due to severe fugitive emissions of gases produced during the batch PS (Peirce-Smith) converting step. In this work, the results of an investigation on the pressure leaching with sulfuric acid and oxygen of white metal (produced in a Teniente Converter reactor) are discussed. The study was carried out at laboratory scale and the main variables studied were temperature, concentration of sulfuric acid and partial pressure of oxygen. The experimental results indicated that most of the sulfur in the white metal was oxidized to sulfate in the whole range of temperature studied (105ºC to 150 ºC). The concentration of sulfuric acid over 0.05 M, and oxygen partial pressure over 6 atm had little effect on the dissolution of copper from the white metal. On the other hand, temperature had the most significant effect on copper dissolution; below 130 ºC copper dissolution was incomplete after 5 hours of leaching while at 150 ºC the dissolution was complete in 90 minutes and 10 atm of partial pressure of oxygen

Jan 1, 2006

By T. Lezhava

For the purification of quarry waters from copper and their further utilization a three-sectional electrochemical reactor is constructed providing the extraction of 90-95% copper as a self-loosing powder from the quarry water running as a steady flow. Four variations of the integrated processing of quarry water are developed and their relative technical and economical parameters are calculated. The detailed technological scheme is given for the variant that is the most profitable for Georgia.

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006