Search Documents

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941

By S C. Dominy

The gravity recoverable gold (GRG) parameter reflects liberated gold or gold-dominated composite particles that can be recovered by gravity separation. Recoveries depend upon mineralogy, in situ particle size and the comminution and extraction method used. Any ore bearing >15 per cent of gold greater than 50 ¦m in size is likely to have a GRG component. The principal characterisation methodology applied is the three-stage GRG (3GRG) test, based on a 40 kg to 100 kg sample. An alternative is the single-stage GRG test (SGRG), which is generally based on a 20 kg sample. Experience has shown that GRG values can vary throughout an orebody, particularly within different grade and/or mineralogical domains. Test programs must consider sample frequency and mass. This study demonstrates the variability of GRG results based on different sample masses. Consecutive underground faces on a coarse-gold dominated quartz vein were sampled taking five different masses from each. Each sample was processed using a SGRG approach. Subsequently, each development round was batched through a small gravity production plant. The results show that the small samples understate the plant GRG and show inter-sample variability. Large samples show less variability and a SGRG closer to the plant GRG. A high SGRG broadly correlates to higher gold grades, more coarse gold and larger gold particles. These results are intuitively correct, but indicate the likely challenges of sampling for gold recovery in heterogeneous systems.CITATION:Dominy, S C, 2013. Variability of gravity recoverable gold values in relation to test sample size, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 293-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By D. M. Davidson, P. F. Kerr

The Permian Cutler Formation in Kane Creek, Utah bears uranium ore in fissure-type vertical veins. This fissure vein formation and its associated host rock bleaching, weak argillic alteration, and base-metal sulfide mineralization along with the development of hydrothermal minerals, a 60 m.y. isotopic Pb/U age, and well-crystallized uraninite's structural control, give evidence of ore deposition in a hydrothermal environment consistent with Laramide mineralization. Mica polymorph studies indicate first, that temperature during the hydrothermal alteration or subsequent ore deposition did not exceed 200°; hence Cutler deposits are classified telethermal; and secondly, that rock alteration and ore deposition are closely related both in time and space, as is seen in argillic alteration sequence. Ore deposition in an alkaline to slightly acid reducing environment is postulated. Ore textures and mineral associations and distributions also indicate that carbonate complexes may have been transported with the deposing ores. Bleached rock formations are not primary strati-graphic phenomena. Bleaching, or changes in ferric iron content, results from a chemical process involving reduction and conversion of hematite to a soluble aqueous ion. Nearby Chinle bedded deposits (Moss Rack sandstone), containing shale lenses, fossil wood, organic debris and minor fractures, overly the Cutler formation. Chinle ores have a single reported isotopic age of approximately 200 m.y. Their chemical environment is assumed similar to that of the Cutler ores, though slightly more acidic. Two genetic, paradoxically divergent interpretations of the bedded deposits are derived from available spectrographic, petrographic, X-ray and chemical analyses. Kane Springs canyon is located southwest of Moab, Utah, south of the Colorado River and northwest of the Lisbon Valley mining district (Fig. 1). Uranium deposits occur along the northeast flank of a Kane Creek salt anticline where two geologic formations bear ore, the Permian Cutler and the Triassic Chinle. The Cutler deposits' fissure vein formation is an unusual occurrence in the Colorado Plateau. The Chinle deposits appear to be of the normal sedimentary type. Associated with the vein deposits are a number of features, including argillic alteration of sedimentary strata. The minerals of these deposits and their associated features have been studied in detail in a two year program entailing both field and laboratory techniques. STRATIGRAPHY A stratigraphic section of the lithologic units in the Kane Creek area is given in Table I.

Jan 1, 1967

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By Vedala Sastry

Longwall mining for coal extraction in deeper deposits is gaining momentum in India, due to the increasing stripping ratios and depletion of shallow deposits amenable for surface mining. In longwall mining, presence of multiple seams with varying interburden thickness is a major problem especially while planning for over-mining. An investigation program was taken up to analyze the effect of the presence of goaf and virgin coal blocks in already developed and extracted lower seam by bord and pillar mining, on the stress distribution in the longwall panel in upper seam. Studies revealed marginal increase in horizontal and shear stress as longwall face passes above goaf to the virgin area present in lower seam. Stress distribution over chock shields was considerably affected when the face in upper seam reached 15-25m zone above the galleries in the lower seam. A clear influence of the presence of solid coal, galleries and goaf in lower seam was found in the loading of longwall panel in upper seam.

Jan 1, 2007

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By Nicholas Macrae Steven

Abstract - The Shaba-type Luamata Cu-Co(-Ni) deposit (11°50_S, 24°28_E) is located in a tectonic slice of Katangan Roan Supergroup (Mines Group) sedimentary rocks, surrounded by younger Kundelungu Supergroup lithologies in the external fold and thrust belt of the Lufilian Arc. Luamata is a classic central African copper clearing in dense woodland, visible as a tonal botanical anomaly on Landsat imagery. Supergene Cu-Co mineralization (especially malachite and subordinate chalcocite, digenite, covellite, and copper and cobalt oxides) and, probably hypogene, bornite, and chalcopyrite are hosted by altered, but essentially unmetamorphosed, moderately dipping, dolostones and dolomitic shales. Alteration products include talcose dolomite, sericite rocks and intense silicification and brecciation. Friable yellow shale is best mineralized with cobalt (up to 0.43 wt%), whereas, highest copper grades occur in brecciated, silicified shale (up to 13.5 wt% CuO). Soil copper and cobalt contents are up to 2.2 and 0.6 wt%, respectively. A newly identified nickel zone (where soil contents exceed 0.1 wt% Ni) fringes the Cu-Co deposit. Polymictic, matrix-supported breccias with a calcareous matrix that underlie the Cu-Co deposit are interpreted to be fluidization breccias related to thrust tectonics and the emplacement of the Mines Group slice. Although small compared to the Kolwezi district Shaba deposits in the Democratic Republic of the Congo, Luamata exhibits all the classic features of an ore deposit type (with low calcite contents), whose high metal concentrations could potentially be very profitably exploited by low-cost opencast mining and hydrometallurgical recovery methods.

Jan 1, 2000

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By J. Miettunen

"The lining of a grinding mill has an important role in creating the conditions for the grinding process. The main purpose of the lining is to transfer the energy taken by the mill motor to the contents of a mill. The power draw curve of the mill, if measured with sufficiently short intervals, describes how well the lining works in lifting and mixing the material to be ground.The power draw curve can also be used for determining the volumetric filling of a mill. This new measuring technique was developed at the Pyhasalmi concentrator in 1989-90. The measuring device with its PC-connections offers an excellent tool for controlling volumetric mill filling, for maximizing throughput and for research purpose (e.g. process studies, mill linings design).The paper describes the new method and the results achieved at Outokumpu's concentrators.INTRODUCTIONVarious methods have been developed for measuring mill load; weighing, noise, etc. Weighing is one of the most reliable methods but installing the sensor to existing mills is often difficult. Besides the load measurement does not indicate the volumetric filling if the specific gravity of the mill feed fluctuates. Noise measurement has often failed with its sensitivity to various disturbance sources.As known, the power draw measurement is one of the most accurate measurements in grinding circuits and therefore it has been utilized in sophisticated control, e.g. in power peak seeking algorithms for maintaining maximum grinding efficiency.About 10 years ago power oscillation measurement was developed at Pyhasalmi concentrator. In this method the amplitude of the oscillation caused by the lifters was measured. The oscillation amplitude and the mill filling has quite a good correlation and together with the power draw measurement it could be used for maximizing mill throughput (Koivistoinen and Miettunen, 1989). The main difficulties in this method were that the dependence between mill filling and the amplitude is unlinear and that the dependence also is individual for each mill.The method developed during 1989-90 is also based on the power oscillation but on its phase shift. In principle level of the material in a mill is measured. The method has been successfully used for maximizing throughput at Pyhasalmi and Enonkoski concentrators and at Harjavalta slag concentrator."

Jan 1, 1991

By J Merrells

Fluor, together with our clients, has yielded significant reductions in the total cost of mining projects by employing a systematic and methodical process of cost reduction. This paper outlines this structured approach to reducing the total cost of projects through the gathering of information, the evaluation of the zero base design, and the development of the execution strategy for the project in the study phase.Over the recent iron ore boom the cost of growth projects escalated rapidly due to a variety of factors including the engineering cost of re-designing facilities, construction in remote areas and an increase in the ‘perceived’ capital requirements for maintainable and operable facilities.Fluor has made strategic steps towards safely reducing the capital intensity of projects, by working with clients to develop zero base designs which utilise the minimum technical requirements in order to meet the function of the plant and then add cost for safety, maintenance and operability only where clearly justified.This paper has set forth a structured three phased approach to focus the team on reducing capital cost while maintaining a low increase in engineering effort.The initial ‘gather’ phase focuses the team on acquiring information and identifying decisions that will need to be made so that the team can prioritise and focus the attention on areas that will provide the greatest benefit. Within this phase the identification of zero base design requirements, review of lessons learnt and analysis of capital cost levers, allows the team to identify the key decisions on the project that will affect the capital cost.In the subsequent ‘evaluation’ phase the team established the zero base design, using the hierarchy of cost reduction as a guide to focusing the team’s attention on high yielding cost saving opportunities.In the final phase the team develops the execution strategy which will yield the least cost using strategies and tools such as modularisation, standardisation, replication, strategic sourcing and 3D design.CITATION:Merrells, J, 2017. Reducing total project cost in the study phase using zero base design, in Proceedings Iron Ore 2017, pp 621–626 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. Stacey

This study was undertaken to generate a locally relevant guideline for the socio-economic aspects of mine closure for South African closure practitioners and decision makers. It should also represent a resource for interested and involved stakeholders. Mine closure, and its related post-closure social, environmental and economic characteristics, is part of the lifecycle of mining operations, given the finite nature of the ore resource. Many coal mines are anticipated to close in the next ten to fifteen years in Mpumalanga, as the epicentre of the industry shifts towards the Waterberg. Social aspects of mine closure have been historically underplayed, and under researched. Coaltech thus commissioned two studies, the first of which examined the closure dynamics of 36 mines in Mpumalanga and KwaZulu-Natal in 2006. A follow-up study (July 2007) focusing on Mpumalanga3,4 confirmed some of the results of the first study. It also contained broad guidelines for mine closure covering social and labour planning, job creation, the use of mine infrastructure, developmental incentives, and environmental rehabilitation.

Jan 1, 2010

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By D Craw

At Reefton, mesothermal gold deposits occur in the Ordovician Greenland Group basement and bituminous coal deposits occur in overlying Eocene Brunner Coal Measures. These different resource types occur in close proximity to one another in the same topography, vegetation and climate. Both types of resources have been mined for many years and as a result historic mining areas discharge water with chemistry reflecting the mineralogy of the deposits. Coal measures release natural acid rock drainage throughout the region due to oxidation of pyrite in coal and associated sediments. Levels of acidity are increased in mining areas, and pH near three is common. Gold mines contain pyrite, arsenopyrite and stibnite. Discharge waters from these sites have pH near seven because of the high acid neutralising capacity of the basement rocks. Both coal and gold mining sites have iron oxyhydroxide precipitates in drainage waters. These precipitates are more abundant at gold mining sites, and one deposit is up to 5 m thick. Iron oxyhydroxide at coal mine sites contain Zn (up to 89 ppm), Ni (up to 10 ppm), As (up to 163 ppm), Cr (up to 23 ppm), Pb (up to 16), and Cu (up to 11 ppm). Jarosite group minerals have been identified in the coalmine iron oxyhydroxide, although most of the material is amorphous. Gold mine iron oxyhydroxide contains Zn (up to 353 ppm), Ni (up to 592 ppm), Cr (up to 17 ppm), Cu (up to 72 ppm), Pb (up to 29 ppm), Sb (up to 230 ppm), and this material is particularly high in As (up to 20 wt per cent). Most of the material is amorphous but distinctive zones (mm scale) are As rich (up to 30 wt per cent As oxide). Pharmacosiderite, K2Fe4(As04)3 (OH)5.6.3H20, is a secondary mineral in one deposit. These iron oxyhydroxide deposits are useful indicators for the metals mobilised into the environment by oxidation in the historic workings.

Jan 1, 2003

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By Enrique Garay

Actualmente el geólogo de mina toma información rutinaria, mapea los bancos de la mina, los taladros para voladura y loguea los núcleos de perforación y fragmentos del aire reverso. Para la localización en el campo utiliza un GPS que tiene una estación en tierra que permite triangular en tiempo real. En ese sentido, el presente texto señala la importancia de la función del geólogo y las herramientas de campo que utiliza para la exploración y la definición del modelo geológico en la mina Pierina. Así para la digitalización del mapeo geológico utiliza el programa AutoCad, en el caso de mapeo de taladros para voladura emplea un Colector de Datos que posee una hoja de calculo que permite recoger datos del tipo de alteración, porcentaje de arcillas, dureza y tipo de mineralización. Finalmente, la información que genera el geólogo de mina es útil para diferentes usuarios ya que sirve para mejorar el cálculo de reservas, manejar el control eficiente del minado de mineral y desmonte, así como generar el soporte geológico a los geotecnistas responsables del estudio de estabilidad de taludes del tajo abierto, así como desde el punto de vista ambiental es posible definir zonas con potencial de generar drenaje ácido de rocas.

Aug 25, 2002

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005