Search Documents

The Martha deposit is an economic giant epithermal gold deposit, with mined and unmined resources of more than 218 000 kg (7 Moz) Au. The Au-Ag, base metal sulphide-bearing quartz lodes in the Martha deposit form an extensive braided pattern within hydrothermally altered andesite wall rock. There are five main quartz lodes: 1.      Martha, 2.      Welcome, 3.      Edward, 4.      Empire, and 5.      Royal.   Information from historic mine plans and reports has been used to determine the depth distribution of economic ore within the Martha deposit. Economic ore (average of 10 g/t Au) in the Martha underground mine was at a maximum width and strike length between a vertical depth of 160 and 350 m. Below this depth the quartz-sulphide lodes continue, but the grade declined to sub-economic grades (< 4g/t Au) at about 575 m depth and economic ore shoots were localised, mainly on the hangingwall side of the lodes. Samples from exploration drill holes indicate that this decrease is associated with a depth zonation from electrum-bearing Zn-Pb-Cu-Ag sulphide ore (average 10 g/t Au) to sub-economic (< 2 g/t Au) electrum-poor Zn-Pb sulphide mineralisation.

Jan 1, 2006

By W. F. Wyman, S. F. Ravitz

"INTRODUCTION By far the greater part of the high-grade manganese ore used in the United States is imported from overseas. During the early part of the recent World War importations of manganese ore were seriously threated, and it appeared that it would be necessary to utilize low-grade domestic ores to the fullest possible extent. Among the processes that appeared to offer the best possibilities for beneficating low-grade domestic oxide manganese ores, which ordinarily are net readily amenable concentration by ore-dressing methods, were those involving leaching with sulfur dioxide. The Bureau of Mines therefore investigated the amenability of a large number of such ores to sulfur dioxide leaching.Several sulfur dioxide processes for beneficiating low-grade oxide manganese ores have been proposed. 3/ One of these, based on a patent by Van Arsdale and Maier, 4/ was used recently in a plant constructed to treat 1,000 tons per day of 20-percent manganese ore from the Three Kids deposit near Las Vegas, Nev. 5/ In this process the ore slurry is leached with sulfur dioxide gas, the resulting solution is evaporated to crystallize the manganese sulfate, the crystals are decomposed thermally to produce high-grade manganese oxide and regenerate sulfur dioxide, and the manganese oxide product is nodulized. The Bureau of Mines has recently developed a process 6/ in which a suspension of the ore in calcium dithionate solution is leached with dilute S02 gas, the manganese is recovered from the resulting solution by a simple lime precipitation, and the precipitate is nodulized or sintered to form a high-grade manga¬nese oxide product."

Jun 1, 1947

By Maurice Magee

The Ducktown ore deposits have been known, explored, and mined for 120 years. Eight massive sulfide ore bodies occur in highly folded and metamorphosed graywacke, graywacke conglomerate, mica schist, chloritegarnet schist, and staurolite schist of Precambrian age. The ore deposits are tabular bodies that have been extensively folded, generally conform to the enclosing rocks, but show local complex differences. The ore deposits, ranging in size from 250,000 tons to over 20 million tons, are composed principally of the minerals pyrrhotite, pyrite, chalcopyrite, sphalerite, and magnetite. Gangue minerals are quartz, calcite, actinolite, tremolite, hornblende, garnet, and masses of schistose wall- rock. Three fault systems are present that have influenced ore control and ore body configuration. Hydrothermal effects are evident in wall-rock alteration. Evidence of retrograde metamorphism is extensive in the wall and ore associated rock. Preliminary isotopic age dates have indicated four possible metamorphic events during the Paleozoic Era. Ore genesis is considered to be hydrothermal replacement of receptive beds, predominantly highly calcareous zones, quartzitic zones, and brecciated shear zones. Ore deposition is thought to have occurred during the Devonian Period, with later mobilization and recrystallization of the ore and gangue during Middle and Late Paleozoic times.

Jan 1, 1968

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By G Baird, M Seto

Reliable evaluation of in situ stress is an important phase in the analysis and design of underground excavations, particularly for evaluating the stability of underground structures to prevent failure or collapse. A technique for the estimation of the full stress tensor based on acoustic emission (the Kaiser effect) is being developed and trialed at the WA School of Mines. The result obtained compare well with the standard over-coring method. The advantages of the technique are that it is relatively cheap, non-time consuming and is applicable to in situ stress measurements at depth in remote regions.

Jan 1, 2002

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By Steven J. Page, Andrew B. Cecala, John A. Organiscak

In This Chapter [Drill dust control: wet and dry Enclosed cabs on drills and mobile equipment Haul road dust control] Overburden drilling generates most of the respirable dust that affects workers at surface mines. Both wet and dry methods are available to reduce this drill dust. Overburden removal by mobile excavation equipment such as bulldozers, front-end loaders, and haulage trucks can be dusty, particularly under dry and windy conditions. Tightly enclosed cabs with dust filtration systems can substantially lower the dust exposure of both drill and mobile equipment operators. Haul road dust control can be achieved by water application or chemical application. DRILL DUST CONTROL [Drill dust is controlled with wet or dry systems. Wet systems can be more efficient, but may freeze in the winter. Dry systems require careful maintenance of the drill deck shroud. An improved deck shroud is shown.] Wet Suppression. Wet drilling systems pump water into the bailing air from a water tank mounted on the drill. The water droplets in the bailing air trap dust particles as they travel up the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole [Page 1991]. In wet drilling systems, typical water flow rates are 0.1 to 2.0 gpm depending on the size and type of drill and the moisture level of the overburden. The drill operator controls the flow using a control valve located in the cab. Some drills are equipped with a flow meter to give the opera-tor a visual sign of the flow rate. Raising the water flow will improve dust capture, but too much water causes operational problems. Because of this, the drill operator must exercise care in find-ing the best water flow rate.

Jan 6, 2003

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012

By S. M. Carpenter

In response to the FY2008 Consolidated Appropriations Act (H.R. 2764; Public Law 110?161), the United States Environmental Protection Agency (USEPA) issued the final Mandatory Reporting of Greenhouse Gases Rule (MRR). The rule, signed by the USEPA Administrator, Lisa Jackson, on September 22, 2009, requires reporting of greenhouse gas (GHG) emissions from large sources and suppliers in the United States, and is intended to collect accurate and timely emissions data to inform future policy decisions. The MRR will go into effect on January 1, 2010, and a report of the total emissions for calendar year 2010 will be due to the USEPA by March 31, 2011. Under the final MRR, suppliers of fossil fuels or industrial greenhouse gases, manufacturers of vehicles and engines, and certain facilities that emit 25,000 metric tons or more per year of GHG emissions are required to submit annual reports to the USEPA. The gases covered by the rule are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), hydrofluorocarbons (HFC), perfluorocarbons (PFC), sulfur hexafluoride (SF6), and other fluorinated gases as outlined in Table A-1 of Subpart A of the MRR, which is also provided in Appendix A of this report.

Jan 1, 2011

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By D. F. Strong, P. P. O'Neill

"The Isle aux Morts Prospect is the first polymetallic, sulphide mineralization reported from the Port aux Basques Complex of southwest Newfoundland. Zn-Pb-Cu-Ba-Ag mineralization hosted by quartz-muscovite semipelite, occurs at the contact between a quartz of eldspathic unit and pelitic unit with intercalated amphibolite are minerals comprise sphalerite-galenachalcopyrite, in order of decreasing abundance. The principal gangue minerals are quartz, muscovite, feldspar and barite. Three morphologic types of mineralization are present: massive with more than 50% sulphide, flanked on one or both sides by disseminated and/or banded types. The massive type of mineralization exhibits a :durchbewegung"" fabric of rounded silicate fragments in a sulphide matrix, characteristic of intensely deformed and metamorphosed sulphide bodies. Sulphide minerals have been mobilized and recrystallized and share the same metamorphic and deformational history as the host rocks. Quartz muscovite schist which hosts disseminated mineralization, displays a K2O enrichment and Na2O depletion, that is typical of alteration associated with sulphide bodies in volcano sedimentary sequences. Isotopic ratios of sulphur are comparable to those of volcanogenic massive sulphide deposits.Despite penetrative deformation and metamorphic recrystallization, features of the local geology and the mineralization suggest that the Isle aux Morts Prospect is volcanogenic in origin. IntroductionFollowing the release of a government lake sediment survey (Butler and Davenport, 1980), which indicated anomalous concentrations of metals in southwest Newfoundland, geologists with Utah Mines Ltd. discovered the Isle aux Morts Prospect, a Zn-Pb-Cu-Ba-Ag showing, located approximately 15 km northeast of Port aux Basques (Figs. I and 2). The mineralization occurs in quartz-muscovite schist and is the first significant basemetal discovery in the Port aux Basques Complex."

Jan 1, 1988

By Simon D. Strauss

Production and consumption of nonferrous metals in the United States during 1950 were at peak levels for the postwar period, as is shown in Tables I, II, and III. The trend of production was upward through most of the year. At the year end, with the possible exception of the Tri-State zinc-lead district, the large mining operations in the country were running at capacity. The absence of serious labor interruptions during the year was an important contributing factor in the increased out-put of metals, since in each of the previous postwar years there had been a number of major strikes which affected production adversely.

Jan 2, 1951

By J M. F Clout

Geological, textural and mineralogical classification of iron ores is routinely conducted by mine and exploration geologists on reverse circulation percussion, blasthole cone and bulk samples for grade control, defining ore and waste, determining lump:fines ratio and predicting downstream processing characteristics. Classification is based on physical hardness, colour, streak and other visual characteristics. However, logging is generally restricted to the five to 20 per cent of chips above about 2 mm. This means that most of the sample is too fine to be reliably logged for anything but colour or streak and the textural types must be inferred from other information. A recently developed software package called æRecognitionÆ allows automated identification and classification of iron ore textural types and gangue on a particle basis in polished section down to 0.01 mm using processed digital images. It is not designed to be used as a routine logging tool, but is applicable where higher definition is required at the resource evaluation stage on selected percussion, drill core or bulk samples. æRecognitionÆ processes data obtained after optical image analysis of fine iron ore samples. It contains several parts, like æRecognitionÆ, æCompositionÆ, æLiberation by Total IronÆ, æLiberation by PhasesÆ and æStatisticsÆ, which allow vast and diverse information to be obtained about the iron ore samples being studied. Identification and classification of the textural type of each particle is performed according to the CSIRO-Hamersley Iron Ore Group Classification Scheme. The recognition procedure encompasses a good knowledge of different ore types and a logical knowledge tree, managing fuzzy boundary problems and the potential for a few different ore types in the same particle to be considered. This new technology introduces strict criteria to make the process of identifying particles more objective. Automated recognition standardises the identification procedure and significantly saves time. It enables users without a strong background in mineralogy to perform accurate texture identification. The æRecognitionÆ package has a modern user-friendly interface and Word compatible output. The combination of all the features mentioned makes the package a convenient tool for detailed studies of fine iron ores.

Jan 1, 2005

By C. Özgen Karacan

Methane emissions from the active face areas and from the fractured formations overlying the mined coalbed can affect safety and productivity in longwall mines. Since ventilation alone may not be sufficient to control the methane levels on a longwall operation, gob vent boreholes (GVB), horizontal and vertical drainage boreholes, and their combinations are drilled and used as supplementary methane control measures in many mines. However, in most cases, the types of degasification wellbores chosen are decided based on previous experiences without analyzing the different factors that may affect this decision. This study describes the development of an expert classification system used as a decision tool. It was built using a multilayer perceptron (MLP) type artificial neural network (ANN) structure. The ANN was trained using different geographical locations, longwall operation parameters, and coalbed characteristics as input and was tested to classify the output into four different selections, which are actual degasification designs that US longwall mines utilize. The ANN network selected no degasification, GVB, horizontal and GVB, and horizontal, vertical and GVB options with high accuracy. The results suggest that the model can be used as a decision tool for degasification system selection using site- and mine-specific conditions. Such a model can also be used as a screening tool to decide which degasification design should be investigated in detail with more complex numerical techniques.

Jan 1, 2009

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Considerations in the mine shaft layout, design, sinking, outfitting, testing and commissioning are set forth against the background of requirements of applicable parts of Code of Federal Regulations, Title 30.

Jan 1, 1988