Search Documents

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

The mining industry continues to experience a skills shortage and this is having an impact on the ability of mining companies to operate sustainably. Apart from a few exceptions, there is a dearth of geologists, mining engineers, metallurgists as well as environmental scientists and other professionals in the global mining industry. This relates to both quantity and quality. It makes good business sense for mining companies to employ local professionals rather than expensive expatriate staff. In some cases a mining company could employ more than 10 local mining engineers for the cost of one expatriate. However, in many countries local professionals are not always equipped professionally to work on mine sites. The result is that many companies are not operated optimally due to human resources gaps. In some cases, particularly in key areas such as mine planning, this threatens the sustainability of the operation or at the very least results in sub-optimal resource utilisation. This paper briefly presents some of the issues and strategies being implemented and that might be implemented to maintain a sustainable supply of quality minerals graduates to the industry in 2011 and beyond.

Jan 1, 2011

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

This paper is concerned with the blasting of rock in mining. The most common purpose of blasting rock is to cast it or to disrupt its structure sufficiently for effective digging and subsequent removal.

Jan 1, 1991

By A. D. Davis

Limestone-based technology for arsenic removal from water is an innovative and promising method. The technology offers the potential for low-cost disposal of a stable waste product after arsenic removal, either in an ordinary landfill or by encapsulation in concrete. Leaching research described in this paper shows that the limestone waste, after encapsulation in concrete, passes the Toxicity Characteristic Leaching Procedure (TCLP) test. Leaching was less than 0.05 mg/L, which is 1/100 of the U.S. EPA?s standard for disposal of arsenic in a landfill. Disposal of arsenic-enriched waste is critical for commercial viability of arsenic-removal technologies. Low-cost disposal gives the limestone-based method an advantage that could help communities meet the new maximum contaminant level of 10 parts per billion for arsenic in drinking water. The ability to recycle the waste material in concrete could add a significant economic benefit, further reducing overall costs.

Jan 1, 2009

By J. A. Botín

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require of more complex risk evaluation models, that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, production rates, among many other). In this context, Real Option Valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed, which successfully quantifies the risk associated to dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mining Project.

Feb 27, 2013

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of ,Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal- mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By Tianrui Xu, Chaohong Liu, Bangqing Ding

The authors were responsible for a series of large scale multiple chamber charge blasts conducted in the granite mountain area for making construction space on the southeast sea coast in China during 1993-1996. This paper describes the blast design and damage control of one mountain blast 320m in length and 280m in width in the vicinity of two wharfs and a dam. In order to obtain better rock fragmentation and muckpile, the explosive charge should be well-distributed in the mountain. The charge pattern, therefore, was designed with mainly 5 rows of tunnel charge in regular terrain in combination with a chamber charge in irregular topography area and the maximum burden was limited to be less than 38m. In order to protect the dam and wharfs the firing sequence was carefully arranged in 29 intervals and the distance between different charges of the same delay to the dam or wharf was taken into account as an additional delay interval based on the difference of p-wave propagating times. The maximum charge fired in an interval was also limited to less than 34t explosives through dividing the larger charge by a stemming deck.

Jan 1, 1998

By S Hapugoda, M Kilburn, M Adam, L Lu

Lump ore is one of the key ferrous materials used in the blast furnace ironmaking process, typically accounting for 5–25 per cent of the blast furnace ferrous burden. Like other ferrous materials, the characteristics of lump ore have an important impact on stable operation and productivity of a blast furnace. As the cold burden lands on the top of the hot burden in the furnace and descends, it is inevitably subjected to thermal shock, which will likely lead to breakdown of the lump particles, or decrepitation and affect the gas permeability inside the blast furnace adversely. An ISO decrepitation test has therefore been developed to assess this behaviour of lump ore. However, the results obtained according to the existing standard decrepitation test method vary considerably between laboratories even for the same lump ore. To improve the test procedure of the existing decrepitation test, this paper first discusses the mechanisms leading to decrepitation and then studies the factors affecting lump ore decrepitation. Understanding the key factors affecting lump ore decrepitation is particularly important to improve the existing test procedure that enables researchers to achieve a higher degree of precision when conducting the decrepitation test.CITATION:Lu, L, Adam, M, Hapugoda, S and Kilburn. M, 2017. Decrepitation of lump iron ores, in Proceedings Iron Ore 2017, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By J. W. Town

The Bureau of Mines determined the physical properties of southeastern Idaho phosphate fines as related to mineral composition, particle size and liberation, beneficiation, and potential use in structural clay products. The phosphate mineral in the fines was identified by unit-cell dimensions to be essentially the same as the phosphate mineral fluorapatite identified in the coarser sizes. The mean particle frequency as determined by electron-microscopy and pipet-analyses was between 0.5 and 0.2 micron. Liberation of the phosphate could not be definitely determined because of the weathered condition of the minerals and their extreme fineness. No beneficiation scheme was developed that would concentrate the phosphate into a marketable fertilizer product; therefore, forming and firing tests were made to demonstrate that the fines can be used to manufacture structural clay products.

Jan 1, 1968

By K. Short

Over the past several years, the mining and minerals market was overloaded with discussions around reviving mature terminologies like distributed control systems (DCS), programmable logic controllers (PLC), and the ?new comers?: hybrid control systems (HCS) and programmable automation controllers (PAC) and, in parallel, which technologies would be more appropriate for mining and mineral processing applications. Ten years ago, a careful comparative analysis would make more sense. Control approaches had very distinctive differences where users needed to choose the right approach.

Jan 1, 2012

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two largest oil-producing States, Texas and Louisiana. Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years, and although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1975

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By Terry McMahon

This Bureau of Mines report describes the rock burst problem and measures being taken for its alleviation in the deep underground mines of the Coeur d?Alene Mining District in northern Idaho. The geologic features that contribute to rock bursting in that area are discussed and briefly compared with similar features in other burst-prone mining districts throughout the world. Early investigations to understand and control rock bursting are reviewed, and the mechanics of bursting are discussed in terms of the seismic events that produce them. Sources of strain energy, rock failure mechanisms, and the conditions necessary for the release of seismic energy are covered in detail. Rock burst research in the Coeur d'Alene District is described. Included are discussions of the microseismic method as both a research tool and as a rock burst monitoring system, rock destress blasting and preconditioning methods for rock burst control, and stoping methods currently being developed to reduce rock burst hazards.

Jan 1, 1988

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining impacts those properties is important in developing effective management practices to control erosion during reclamation. Soils from undisturbed areas, roughly graded mine spoil, replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated to determine impacts on soil hydraulic properties. Field and laboratory studies were conducted to determine soil hydraulic properties, including particle-size distribution, organic matter content, and saturated hydraulic conductivity. WEPP simulations and risk analyses were performed on the soil hydraulic property data to determine the impacts of changes on soil erosion. The hydraulic properties of the soils in each representative area have significant differences due to the mining and reclamation practices at the mine. WEPP simulations show that the potential for soil erosion increases due to mining activities disturbing the soil. WEPP simulations also indicate that the potential for erosion may return to pre-mining levels over time with effective revegetation practices.

Feb 27, 2013