Search Documents

By H. W. Smith, C. L. Lewis

"A process control computer has been installed in the Lake Dufault concentrator to: (a) control the on-stream X-ray analyzer and convert chart readings to elemental percentages, (b) calculate the flow rates required for the most important flotation reagents, using the amount of material entering the process, the analyses and the slurry pH, and (c) set the reagent feeder to these flow rates automatically. Although this project was largely experimental, to gain knowledge and experience in flotation process control, the objectives have been met and fully automatic computer control is now the normal mode of mill operation.This paper describes project planning and defines the system with respect to both control design and functional design. System operation -as seen by the mill operator -is detailed. Implementation of the system is described and the system is discussed in terms of its success, economic justification and future plans."

Jan 1, 1969

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By Cínthia Toshimi Ogata

Processos de fundição de ligas de alumínio com altos teores de Mg são um desafio da indústria, uma vez que diferentes taxas de resfriamento ocorrem em geometrias diversas. Este trabalho tem como objetivo caracterizar a liga de alumínio AA5052 com variações em teores de Mg por meio de experimentos de solidificação direcional transitória, e compreender seus efeitos com relação a evolução de parâmetros térmicos, microestruturais, e propriedade mecânica. As leis experimentais de evolução do espaçamento dendrítico primário (?1) com relação a taxa de resfriamento resultam em: ?_1=640 ?T ?_L?^(-1/4) para a liga 5052 com 2,4%Mg e ?_1=300 ?T ?_L?^(-1/4) para a liga com 3,2%Mg. As leis de crescimento de espaçamento dendrítico secundário (?2) com relação a velocidade de solidificação resultaram em: ?_2=27 ?V_L?^(-1,1) para a liga 5052 com 2,4%Mg e ?_2=15 ?V_L?^(-1,1) para as ligas com 2,6%Mg e 3,2%Mg. Maiores teores de Mg na liga AA5052 proporcionaram uma expressiva redução no valor de ?2 para uma determinada VL. A evolução da dureza mostrou-se diretamente relacionada ao tamanho e a distribuição dos intermetálicos presentes, sendo ?2 o fator predominante neste controle.

Oct 30, 2017

By Lorenzo Bacchetti

Automatic yards with ad-hoc WMS (Warehouse management software), are the key for a modern and efficient warehousing which can face today logistic challenges. WMS boosts the traceability of material while optimizing the storage space. The operations in the yard are safer and logically organized according to algorithms that are specifically adjusted case by case. WMS can easily handle multi-cranes yard avoiding conflicts and increasing accuracy of positioning with decreased number of movements. The synergy of automatic cranes and WMS reduces bottlenecks and speeds up the preparation of deliveries with an overall improvement of warehousing and shipping scheduling.

Oct 1, 2019

Although the mining of metals was well established by the time of the Roman Empire mining skills did not really advance greatly for many centuries. Miners did not have the scientific knowledge to distinguish minerals, to process them, and to obtain the best recovery. Each mine essentially developed its own methods in isolation, most of them dangerous. However, with the beginning of the industrial revolution in the early 18th century there was a rapid increase in mining activity in Central and Western Europe and an accompanying need to educate professionals in the developing fields of science and technology. There was also a need for specialised schools (for example, Schools of Mines) to accomplish this since the universities of the time, formed as early as the first half of the 12th century, were cloistered institutions, focused on the study of classics, theology and law. The earliest attempts at organised technical education were made in 1702 with the establishment of a School of Mines in Frieberg, Germany (Table 1) to service rich copper mines, and in 1747 with the establishment of a School of Mines in Paris. By this time, the industrial revolution was well under way and other Schools rapidly followed, at Clausthal in the Ruhr region of Germany in 1775; in 1777 at Almanden to service the mercury mines of Spain (later transferred to Madrid); in 1780 at St Petersburg, Russia and at Falun, Sweden in 1819. The academic staff for these new institutions were often trained in the original School at Frieberg.

Jan 1, 2002

By Edmund Newton

The Haile mine has been the outstanding gold-mining operation and the largest single producer of gold in the Appalachian region. Gold was discovered at the Haile in 1827, previous to the present operation, production has been nearly $4,500,000 (gold at $20.67 per ounce.) from somewhat over a million tons of ore, with an average extraction of about 70 percent. The Haile property, now operated by Haile Gold Mines, Inc., is in the southern part of Lancaster County, South Carolina, 3-1/2 miles northeast of the town of Kershaw and 55 miles north of Columbia, the State capital. (See fig. 1.) The corporation has a lease and purchase contract on 1,805 acres, covering the present productive area. In addition, it holds lease contracts on 1,500 acres additional adjacent to this area.

Jan 1, 1940

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By T. Szendrei, S. Tose

The generally accepted view in rock blasting is that the sources of energy for the fracture and movement of rock reside in the shock wave and gas action resulting from the explosion, and yet the mechanisms by which these sources interact with the rock have remained unclarified. It has also been noted that up to 50% of the work capacity of an explosive released in a blast cannot be accounted for by field measurements of energy partitioning. In this study, we describe a physical model that details the response of rock to both shock wave and gas action. An analytical model based on momentum conservation is derived to describe the dynamics of shock-driven expansion of the blasthole. Radial expansion of the hole is the key parameter that permits the derivation of the following characteristics of rock response to shock loads: hole expansion time; volume of displaced rock; energy consumed per unit volume; expansion energy efficiency; stress wave pulse length; gas pressure in enlarged hole. Soon after the completion of hole expansion, the shock wave degenerates to an elastic stress wave that runs through the burden. Blasthole expansions of between 50% and 300% of diameter are completed in under 1 ms and, depending on rock properties, consume 32% to 42% of the detonation energy or about 55% of the available mechanical (Gurney) energy. Gas pressure in the enlarged holes in five rock types is between 35 MPa and 650 MPa, and drives the mass movement of burden rock.

Oct 9, 2024

By P Williams

The Sunrise deposit is one of AustraliaÆs largest and most profitable gold deposits. It has consistently and spectacularly outperformed every resource model created. Currently over the life of the Sunrise pit there has been a 50 per cent under estimation of ounces mined. Without a solid basis for predicting the tonnes and grade or the spatial location of mineralisation, mine planning becomes problematic. Recently, through a better understanding of the mineralising processes the reconciliation of the resource model has improved to be in the order of ten per cent under on ounces mined. This paper will describe how the mine geologists at Placer Granny Smith have implemented the changes required to improve the resource model. Work began with the development of a three-dimensional lithological and structural model based on historical drilling and pit mapping. Continual updating of the geological model with grade control logging, assays and in pit face mapping, now allows for the on-going improvement of the resource model and the planning of mine development drilling.

Jan 1, 2000

By S. H. Ash

THIS REPORT covers the second in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the construction work contemplated-to sink two shafts on the line of the main tunnel that are designated the Nos. 9A and 11 shafts, to turn off from the No. 9A shaft the Lansford and Lykens laterals, and to drive portions of the main tunnel. An emergency pumping plant, consisting of 2 separate pumprooms, each containing 3 horizontal-type centrifugal pumps of 100,000-gallons-per-minute (g. p. m.) capacity, will be constructed at the No. 9A shaft. From the No. 11 shaft will be turned off the Trevorton lateral and portions of the main tunnel, which will connect with the section driven from the No. 9A shaft. Under the proposed project, the Lansford lateral will be driven for a distance of 2 miles, the Lykens lateral for a distance of 10.56 miles, and the Trevorton lateral for a distance of 20 miles. To drive the Lykens and Trevorton laterals for the distance indicated, several construction shafts and slopes must be sunk to permit efficient and safe construction.

Jan 1, 1955

By D Lautier, A A. Ndiaye, A Galli

Traditionally gold producers had built up hedge books to protect themselves against adverse changes in the commodity price, but diversified mining groups were staunchly opposed to hedging in any shape or form. The situation has evolved over the past few years. Gold miners have been reducing the size of their hedge books in line with the rising gold price. Commentators have talked about ædouble-digit dehedgingÆ and have suggested that this is the final countdown for gold hedge books. It sounded as if the era of hedging by mining companies was drawing to a close. But as appearances can sometimes be misleading, we decided to find out what mining companies were actually doing. Companies listed on stock exchanges are now obliged to give details of their derivatives holdings in their annual reports. Two or three years ago there was no such obligation. Our reality check was based on the latest annual report issued by three multinational mining groups; two with diametrically opposed views on hedging (Rio Tinto and Barrick) and the third (BHP Billiton) with an intermediate position. This snapshot of their derivative positions at a point in time revealed that Barrick and BHP Billiton have substantial derivatives positions (worth billions of dollars) to protect against adverse changes in foreign exchange rates and interest rates. Moreover Barrick has recently started hedging against increases in fuel prices. Despite its opposition to hedging, Rio Tinto has derivative positions worth several hundred million dollars, but these are primarily a legacy from various mergers and acquisitions over recent years or were entered into as a condition of project financing. Lastly we were surprised to discover that Barrick was holding asset-backed commercial paper (ABCP). So the idea that mining companies donÆt hedge their risks is just another urban myth.

Jan 1, 2009

"INTRODUCTION These safety standards for anthracite mines have been prepared for use as a guide for Federal inspectors. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7282 issued in May 1944 and used as a guide in Federal inspections. No provision made in these safety standards should be construed or operate to nullify any existing State statutes; they are intended to supplement the State statutes in the interest of increased mine safety. Mines are inspected in accordance with the Federal Coal-Mine Inspection and Investigation Act of 1941, Public Law 49, 77th Congress, H. R. 2082. Any unusual hazard noted by an inspector and not covered by these standards will be discussed in the inspection report, and suitable remedial procedure will be recommended.ARTICLE I. - SURFACE STRUCTURESSection 1. Breaker and cleaning plant.Electric switches and controls in breakers and cleaning plants should be enclosed.Where coal is dumped at or near air-intake openings, reasonable provisions should be made to prevent the dust from entering the mine.Section 2. Lamp houseNaphtha or other flammable liquids in lamp houses should be kept in approved containers or other suitable dispensers.Flame safety lamps should be permissible and maintained in permissible condition.Flame safety lamps should be properly cleaned, examined, and assembled by a qualified lamp attendant or other competent person before each period of use. Lamp assembly should again be checked by the person using it immediately before he enters the mine.When not in service, methane indicators, flame safety lamps, and electric cap lamps should be in the custody of competent persons responsible for maintenance and testing."

Feb 1, 1948

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

The United States Bureau of Mines frequently receives requests for information regarding the details of its organization and the nature of its activities. In response to such an inquiry a series of articles outlining the work of the bureau as a whole and of its different divisions was prepared and published in the United States Daily, Washington, D. C., during November, 1929. These articles are reprinted here in the hone that they may assist in giving the public a more complete understanding of the aims and purposes of the bureau and the methods by which it is laboring for the attainment of safer conditions and more efficient methods in American mineral industries. An index of these articles, with the dates of 'their publication in the United States Daily, is given below.

Jan 1, 1930

By G. L. Bartlett

"INTRODUCTION The major objective of our research is to help reduce the incidence and severity of coal worker's pneumoconiosis (CWP). To that end, this project is designed to improve our understanding of the processes that lead to pulmonary dysfunction following mine dust exposure, and how those processes might be interrupted or attenuated. The response of the lung ' to inhaled particles is complex, and the course of development of disabling CWP is slow and unpredictable. From among the numerous cellular and molecular interactions involved in the pulmonary response to inhaled particles, this project is focussed on the role that the pulmonary alveolar macrophage (PAM) may play in regulating the activity of fibroblasts.The PAM is the lung cell that has the most immediate and the most obvious interaction with inhaled particles. Within a short period after particles are arrested in the alveolus of the lung, they are phagocytized (engulfed) by these specialized cells. The PAM then has a diverse potential repertoire of subsequent activities. Which reaction actually ensues is determined, in large part, by the nature of the phagocytized _particles. Activated PAMs produce a variety of products that may affect adjacent lung tissue, including superoxide free radical, elastase, collagenase, prostaglandins, platelet activating factor, etc. Those may well be important in the pathogenesis of CWP, but they are beyond the scope of this project. Background information that is cogent to this project has come primarily from investigations using animal models of silicosis and asbestosis. PAMs that have ingested silica particles synthesize and release molecules that control the behavior of surrounding cells. One such mediator is interleukin-1 (IL-1), a molecule that plays a central role in many aspects of the response to injury. It can stimulate fibroblasts (the cells that help to hold tissues together) to release the enzyme collagenase, resulting in breakdown of the structural collagen fibers that support the lung tissue. IL-1 also stimulates fibroblasts to undergo mitosis and to proliferate, which is an initial stage of fibrosis. Certain stimulants cause PAMs to release fibroblast growth factors (FGFs) that are distinct- from IL-1. Under other circumstances activated PAMs synthesize and release molecules that stimulate fibroblasts to accelerate synthesis of collagen fibers, thus contributing to fibrosis. Although these observations provide a valuable precedent for analysis of the mechanisms involved in CWP, their relevance to CWP cannot be assumed since most of those studies involved macrophages or fibroblasts obtained from tissues other than the lung, and because almost none of them have used CMD as the stimulating particles. Therefore, the goal of this project is to learn how exposure to CMD affects the behavior of PAMs, and in turn how products of dust-exposed PAMs affect fibroblasts and the process of fibrosis in the lung."

Jan 1, 1988

By J. R. Thoenen

"The curtailment of imports of foreign potash during the World War directed attention to the necessity of establishing a domestic source of potash for fertilizer, and considerable study has been given to the subject by Government bureaus, research organizations, and private individuals. These studies have covered all known sources of potash, and among them the extensive greensand deposits of New Jersey in which the potash content is found in the mineral glauconite have been investigated.Several hundred patents have been obtained covering processes for the extraction of potash from siliceous minerals, but up to the present time none have proved successful on a large commercial scale.When the investigation of the potash deposits of Texas was started by the Federal Government, the laboratory study of the drill cores was assigned to the Nonmetallic Minerals Experiment Station at New Brunswick, New Jersey, with the object of ascertaining a possible commercial method of utilization.The purpose of this preliminary study was to investigate existing literature and previous investigations to ascertain the extent and availability of the deposits, the extent of commercial success so far attained in potash extraction, the most promising known methods and by-products obtained from them, probable markets, and possibility of competition with foreign potash, and by a study of these data to determine whether further chemical engineering analysis and laboratory investigation were warranted.As the study advanced it became evident that adequate reserves of green-sand were available for many years supply. and that whereas many processes had been patented few had been tried commercially. In collaboration with former private and Government investigators these patents were first divided into two"

Feb 1, 1929

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d'en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d'acier sont hétérogènes tant au niveau structural que composition chimique. L'examen de quelques produits fin is a mont ré qu 'on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010