Search Documents

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

The principal activities of the Bureau of Mines Explosives Research Center during fiscal year 1969 (July 1: 1968, to June 30, 1969) are reviewed in part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in the outside press. These publications are referenced in part 1 by underlined numbers in parentheses. Other publications, which are not abstracted, are cited in footnotes throughout the paper. ACKNOWLEDGEMENTS The Bureau acknowledges the support received through cooperative agreement in fiscal year 1969 from the Manufacturing Chemists Association. It also acknowledges the sponsorship by the following Government agencies of research conducted during that period: Department of the Air Force, Department of the Army, Department of Health, Education, and Welfare, Department of the Navy, Federal Aviation Administration, National Aeronautics and Space Administration, Space Nuclear Propulsion Office, and United States Coast Guard.

Jan 1, 1970

By F. T. Cawood

The new South African Mineral Policy has major implications on the way mineral rent will be collected and shared between the stakeholders in future. Although the policy does not supply details on how this will be done, drastic departures from practices under the previous dispensation require a new approach. For example, there introduction of the ?right to mine? principle implies that the repealed lease consideration concept will be expanded to all minerals. The new policy also makes provision for predetermined standard terms and conditions for all prospecting and mining permissions. It also states that, regardless of whether the mineral rights are state or privately-owned, all prospecting fees and mineral royalties will be determined by state officials after consultation with the registered holder of the mineral rights. This paper proposes a standard mineral royalty formula that complies with the principles mentioned in the White Paper and has been shown to be internationally competitive.

Jan 1, 2001

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By John Stubbs

Sub-Surface Shaft excavation Mine development Headframes Surface Production facilities Product storage and loading Tailings area Infrastructure Discovery Lodge Utilities Operations complex Port Marine loading Rail unloading and storage

May 1, 2013

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

The gold salting fraud at Busang on the island of Kalimantan, Indonesia was exposed in early 1997 and resulted from the independent drilling, sampling and assaying of PT Freeport Indonesia which reported assays from the South East Zone with negligible concentrations of gold. Since then, a number of legal actions directed at former Bre-X directors, consulting firms and financial or broking institutions are at various stages and are based on numerous allegations surrounding the supposed existence of obvious and numerous warning signs or æred flagsÆ. These include: the absence of references to visible gold in the drill logs; the alluvial nature of the gold grains; the high gravity recoveries; the invalid comparison with Kelian; the absence of outside scrutiny and the lack of external review/audit and surface depletion of gold. The focus on the red flags has been at the expense of the numerous positive indications or ægreen flagsÆ. These include the morphology and chemistry of the gold grains, the gravity testwork, the amalgamation results, the role of external consultants, the results of a review by one of North AmericaÆs leading minerals auditing groups, the behaviour of the gold at surface and the presence of references to visible gold in the drill logs. The flawed nature of the discussion of the technical facts surrounding Busang has prevented a meaningful and informed discussion about what actually happened and has, therefore, prevented the formulation of meaningful remedies for the future.

Jan 1, 2002

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By A. W. Stradling, M. J. Fairweather

"The selective flotation of lead, zinc and iron sulphide minerals is key to the economic performance of concentrators treating zinc-lead ores. Diagnostic metallurgy is a tool to quantify mineral behaviour as a function of particle size and liberation. The result of such analysis may be used to select preferred strategies to improve metallurgical performance. The zinc flotation circuits at three Teck Cominco operations: Sullivan, Polaris and Red Dog are compared here. This paper analyses operating data from each of these circuits. The effects of mineralogy and performance by particle size are emphasized. Metallurgical performance at these three concentrators varies substantially. Liberation size is the major factor in determining metallurgical performance. Complex mineralogy requires a fine grind to achieve effective liberation. Fine grinding results in offsetting decreases in concentrate grade through entrainment. The economic treatment of complex fine-grained deposits requires optimisation of regrind size for liberation without unduly compromising concentrate grade through gangue entrainment.INTRODUCTIONUntil recently Teck Cominco Metals Ltd. operated three mines treating zinc-lead ore. In order of increasing mineralogical complexity they are: the Polaris Mine on Little Cornwallis Island in Nunavut in the eastern Arctic, the Sullivan Mine in southeastern British Columbia and the Red Dog Mine in northwestern Alaska. Both the Polaris and Sullivan Mines have recently ceased to operate due to depletion of ore reserves.The ore type and associated gangue, mineralogy and iron solid solution vary significantly between these deposits. Table 1 summarizes some of the important differences"

Jan 1, 2003

By R G. Barker

This paper reviews the annual status of the New Zealand mining industry (metallic minerals and coal) including key aspects such as mineral production, mineral exploration expenditure, commodity price trends, key industry players, market activity and other significant commercial factors.   Strong commodity prices during 2006 have been underpinned by a number of key factors including US dollar weakness and emerging market demand, particularly from countries such as China and India. In real terms commodity prices have recovered significantly since 2002 and are currently at 20-year highs.   New Zealand exploration spending on metallic minerals (predominantly gold) is at a 15 year high driven by rising global commodity prices. New Zealand gold production in 2006 was about 340,000 oz and is expected to grow in 2007 as new mines at Frasers and Globe-Progress (Oceania Gold) and Favona (Newmont) come on stream. Gold production broadly lags 10 years behind exploration spending and exploration activity over the last five years remains well below that seen in the early 1980Æs. Expenditure on coal exploration shows a similar trend with strong growth from a low base over the last five years, reaching over $11 M in 2006. Total coal production in 2006 was 5.9 Mt, an increase of 10% on 2005 with imports from Indonesia adding a further $1.1 Mt.   Newmont and Oceana Gold are by far the largest public gold mining companies operating in New Zealand, although only Oceana Gold maintains a presence on the local stock exchange. Other metals explorers with New Zealand projects include a range of public-listed Juniors (market capitalisation less than NZ$50m) domiciled largely in New Zealand, Australia and/or Canada. Capital-raising on public markets directed towards New Zealand exploration is estimated at around NZ$12 M for 2006, the bulk of this coming via Glass EarthÆs NZ$10 M IPO on the NZAX in October.   The New Zealand Coal sector is dominated by the state-owned enterprise Solid Energy with around 80% market share by production. Other domestic coal competition remains limited, and includes the L&M Group, Pike River Coal, Eastern Corporation, and New Vale (acquired by Solid Energy in 2007). Pricing parity comes mainly from imported coal and global thermal coal prices have remained strong during 2006 at around US$45-55/t, driven by continued expansion in Chinese demand. Coking coal prices have eased 16% since 2005 to around US$98/t in 2007.   Although recent increases in exploration spending suggest a renaissance in the New Zealand minerals sector, long-run trends indicate that we have simply rebounded from a low base over the last five years and much work is still to be done to stimulate further growth in the mining industry to maintain minerals production at current levels. Key industry challenges include marketing exploration opportunities to local and overseas investors, building a critical mass of NZX-listed explorers and providing an internationally competitive environment to attract further capital and expertise.

Jan 1, 2007

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By K. Burke, K. L. Myers, R. Espell

Barrick Goldstrike’s (Goldstrike) AA Heap Leach Pad is an HDPE lined facility used for gold recovery from low grade ores using conventional cyanide heap leach technology, operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA Leach Pad Facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada’s closure requirements. Traditional Nevada leach pad closure has involved rinsing to reduce cyanide concentration to an acceptable level, followed by reclamation. However, certain metals and compounds are not typically reduced by rinsing and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as Nevada, the fine-grained layer will rarely reach full saturation and the cover will be able to store water during precipitation and allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22 m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the re-contoured AA Heap Leach Pad was specifically designed to enhance the revegetation, reclamation, and sediment yield control aspects of the AA Heap Leach Pad closure, while resulting in a natural looking surface, compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for re-contouring and erosion control design.

Jan 1, 2001

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Darin Cotton, Tim Burgess, Tim Martin

"As the leading US supplier of roof control drills, J. H. Fletcher and Company® has encountered an extensive set of roof strata challenges and has overcome various drilling issues by varying machine parameters and working with customers and tool manufacturers to develop solutions. Every mine wants to drill and install roof bolts as fast as possible with maximum safety at the lowest possible installation cost for their conditions. In most circumstances, the intuitive method of higher speeds and pressures can actually have a detrimental effect on the roof drill safety and performance.This paper will outline recent tests carried out at several different coal mines in the Eastern United States. The tests focused on optimizing the drilling parameters of feed pressure, feed rate, rotation speed, and drill torque.The drill feed, rotation speed, and rotation torque, as well as the type of bit selected, have a definite impact on the performance of the roof drill including drilling speed, safety, and tool life. The drilling process can be improved while also improving operator safety and reducing bolt installation costs by maintaining the appropriate roof drill settings for the specific strata conditions.The advantages of improving the drilling process includes increased bit life, increased drill steel life, reduced hanging drill steels, reduced clogging of the vacuum system, decreased whipping drill steel potential, reduced noise generation, and increased cutting size which reduces fine dust generation and dust collection system servicing.INTRODUCTIONIn recent times, the economic pressures that coal producers are facing have created an increased emphasis on controlling operating costs. Several coal operators have pointed out their dissatisfaction with low bit life, and there is a renewed interest in improving tool life and machine performance as part of an overall cost control strategy. Operators are looking for ways to reduce tooling cost, maintenance costs, and drill downtime without decreasing drill performance. This renewed interest in reducing operating costs, along with the ongoing desire to improve safety, created a perfect environment to take a fresh look at the existing fleet of machines to see what could be accomplished. The goal was to take a practical approach to reviewing machine parameters to determine what changes could be made. The emphasis was on changes that would be feasible to roll out to an entire fleet of machines in a short period of time with minimal capital expenditure. The thought process was that significant improvements could be made by simply tuning up the machine parameters to provide a more efficient and safer bolting process."

Jan 1, 2015

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924