Search Documents

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By L. Ozdemir

An investigation was made to determine the mechanical properties of oil shale at elevated temperatures and confining pressures, the thermal properties at elevated temperatures, and to provide mathematical models for mine design for in situ oil shale retorting. A review of current activity in in situ retorting is included with a comprehensive list of references. Tests were run at temperatures from 20°C to 500°C and confining pressures to 1500 psi with shale of 10 to 30 gallons per ton. A major loss of strength occured in heating 140°C with a partial regain from 380°C to 500°C. Higher grade shale had lower compressive strength. Elastic properties showed large variations. Brazilian tensile strength showed a similar temperature sensitivity as the compressive strength. Equations were developed for each property in terms of grade, temperature and pressure. Thermal, electrical and acoustical properties showed anomalies through the temperature range. Creep is a major factor in overall deformation of heated shale. Oil shale was found to be an excellent insulator. Loss of pillar support area at 800 hours of heating would be about 10 percent. Good correlation was found between a finite element model using the developed properties and an in situ heater test.

Jan 1, 1981

By Jack G. Hazan

The Critical Path Method is the modern scientific answer for solving the planning and scheduling problems inherent in today's complex projects. With this method, nothing is left to chance. All resources are controlled and kept to the minimum. The various phases are properly planned and strategically determined. Optimum conditions are evaluated for the most economical and fastest way to complete a definite project. The method must be fully understood and implemented with positive data and continuous feedback to obtain the best results. This paper covers the various aspects of the Critical Path Method and mentions some of its applications in the mining and metallurgical fields. T 0 progress to a higher state of human welfare necessarily involves sacrifices. The greatest sacrifice is to relinquish social freedom in favour of economic freedom. In the old days, for example, a cobbler was free to work at whatever time of the day he chose; today, he can't. He is now forced to adapt himself to environment and to work at stand-

Jan 1, 1965

By J. J. Gilman

The dependence of ortho kink-band formation on crystal orientation, on temperature, and on the conditions at the ends of a specimen is described. Load-compression curves for crystals that kink are presented. The reversibility of ortho kinking is demonstrated, and motion of kink planes through crystals is shown. Finally, a phenomenological explanation of ortho kink-band formation is given. ORTHO compressive kink bands (Fig. la) were discovered for the case of metals by Orowan,1 and they have been discussed by Jillson2 and in some detail by Hess and Barrett." However, their history in nonmetallic crystals is considerably older. It is not known when they were first observed in mineral crystals, but descriptions of them may be found as early as 1885.* They were sometimes mistaken for twins.6 Mügge seems to have been first to realize their true nature and importance. He reviewed the knowledge of them for a wide variety of crystals: anhydrite, antimonite, kyanite, vivianite, gypsum, mica, graphite, molybdenite, barium bromide, cal-cite, sodium nitrate, and barite. Also, the "twins" observed by Bridgman7 in sapphire crystals resemble kink bands more than twins. The terms ortho and para kink bands have been coined in order to distinguish between two types of kink bands which seem to represent the same geometrical configurations, but which have different origins and sizes. Ortho kink bands are the usual type that form at low loads when zinc crystals are compressed parallel to the basal plane. Para kink bands form at much higher loads in highly deformed crystals. These terms refer to compression phenomena and are not to be confused with analogous tension phenomena such as tensile kink bands and deformation bands. Mügge described the geometry of ortho kink bands quite completely for kyanite crystals, Fig. lc. The geometry observed for cadmium by Orowan1 and for zinc by Hess and Barrett3 is very similar to that described by Mügge. (See Hess and Barrett for a complete discussion.) Mügge associated kinking with bending combined with basal slip. He pointed out that the kink angles

Jan 1, 1955

By Sh. Karimidorabati

In the construction industry, project changes constitute a major cause of delay, disruption, cost increases, poor quality and unsatisfying performance. They are also known as a main factor of litigation between the owners and constructors. Construction projects are essentially process-based, and with the critical role of Information Technology (IT) in this industry, projects, especially mega projects, are being managed remotely. The volume of data and documents, such as Requests For Information (RFIs), different types of Change Requests (CRs) and Project Change Notices (PCNs), being transferred and exchanged amongst the stakeholders of a project is considerable. The circulation of these documents amongst project stakeholders still heavily relies on two methods or levels for management of change process; Conventional (fully paper-based, Faxes, Snail mails) and Electronic or semi-automated (Email, Internet, PDF files). These two methods are dependent on human discipline to follow specified processes which often break down because of human nature. This creates serious compliance problems. It is hypothesized here that fully that automated process-based management of change can lead to better compliance, more efficient management of change, and reduction of time and cost of data exchange. An approach of doing this is presented in this paper. Ultimately, its impact should improve project performance. Conclusions are presented on time savings and improved compliance.

Aug 1, 2013

By C. T. Baroch

This report summarizes cost data accumulated during 15 months of sustained operation of the Bureau of Mines Boulder City (Nev.) titanium plant, which had a capacity of about 1,350 pounds of titanium sponge per day. The plant was constructed during the 1952 fiscal year with funds supplied by the Ordnance Corps, Department of the Army. Its original purpose was to engage in process development work as a continuing phase of the Bureau of Mines policy to seek improvements in producing titanium metal. In early 1953 the Defense Materials Procurement Agency contracted with the Bureau of Mines for producing approximately one-half million pounds of usable ductile titanium sponge. Production began in May 1953, ended in September 1954, and yielded 492,503 pounds of acceptable metal. Operating costs covering this period of operation, with suggested depreciation and administrative costs, are given, as well as outlines of building and equipment capital costs. In addition, miscellaneous economic considerations are discussed, including labor and operating-time schedules.

Jan 1, 1956

By Frank E. Cash, Max S. Peterson

"INTRODUCTION Falls of ground cause the greatest number of accidents at underground metal mines. Statistics compiled by the Federal Bureau of Mines show that during a 13 - year period ended in 1943, falls of ground caused 35 percent of the fatalities and 16.8 percent of the nonfatal injuries at underground metal mines in the United States. 4/ Expressed on a basis of a million man-hours worked, the frequency rate was 0.355 for fatalities and 11.76 for nonfatal injuries. Although some progress has boon made in preventing rock-fall accidents over a 30- or 40-year period, the problem is still a major one requiring the diligent efforts of management and employees.In the Lake Superior district: where organized safety programs have been in effect for more than 30 years, the record is more favorable. Statistics compiled by the Lake Superior Mining Section of the National Safety Council reveal that over a 6-year period ended in 1945 the frequency rate of fatalities per million man-hours was 0.277, and the rate for nonfatal injuries was 2.38 from falls of ground.Although the above-given statistics do not cover equal or concurrent periods, the improvement in accident experience in the Lake Superior district over the national average, is obvious. This improvement is due to more effective methods of ground support or more rigid enforcement of the use of known methods.It is hoped that the following information about ground-support practices in the Lake Superior district will assist operators of other mines in their efforts to reduce accidents from falls of ground."

May 1, 1948

By T. C. Page

The Yarnell gold depoSit, located in the Weaver mining district of Yavapai County, Arizona is found within a structurally controlled, hydrothermally altered zone that occurs within a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rock that occur around and above the low-angle northeast striking Yarnell fault are known to host economic gold mineralization; a wider envelope of weakly-propylitic alterred rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz ± adularia veining, stockwork formation, and localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized), and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit although the thickness of the zone and associated alteration envelope diminish away from the orebody. A sample of undeformed illite taken from the Yarnell fault zone was K/Ar dated at 69 ± 1.6 Ma; this date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As, Cu, and Mo content. Both CO2-and H20-rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit.

Jan 1, 1992

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By Jacob W. Young

A casual reading of the geological literature extant to-day would give one the impression that carbon is an element which by some chance or another always existed at or near the surface of the earth, and was never of a magmatic origin. The carbonaceous matter in shales is said to be of vegetal derivation; petroleum is stated to have been derived from vegetable matter or from marine animal bodies; if carbon or bituminous matter is found in igneous rocks or associated with metallic ores, the statement is made that deeply buried carbonaceous sedimentaries were undoubtedly the source from which such carbon or bituminous matter was derived. This, I do not consider a reasonable or common sense view of the matter. Carbon is one of the elements of which the earth is composed. In the table giving the periodicity of the elements it comes sixth in the order of increasing atomic weights. It is an element formed like all the rest were formed, and must be as common to the interior of the earth as the rest of the eighty-odd elements so far discovered. The spectroscopic analysis of light from the sun, and the stars, shows the presence of carbon in the sun and in the colder stars. Thus with carbon, an element, found throughout the universe as well as on the earth, it is entirely reasonable to consider it as present in the interior of the earth with the other elements. Such being the case, the magmatic origin for the various forms of carbon in rocks and ores is a rational and logical conclusion. If but a small fraction of thought and effort was made along these lines, which is made in fostering the idea of the organic origin of the carbon found in the earth's crust, untold advances in this phase of geological science would result.

Jan 1, 1925

By S. H. Lorain

This paper briefly describes the principal commercial and near-commercial deposits of gold-bearing gravel and the important placer-mining operations in Lemhi County, Idaho. It is on of a series on western mining districts being published by the Bureau of Mines. This paper is based on a field survey of the placer-mining districts of Lemhi County in the summer of 1938. Available information concerning gold-bearing gravels was obtained from prospectors and claim owners; operators supplied the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1939

By N. A. C. Smith, E. W. Dean, W. A. Jacobs, H. H. Hill

Fractional distillation is the most important process in the commercial refining of petroleum. The same procedure, conducted on a small scale, is the basis of a number of analytical methods of wide application in the petroleum laboratory. The Bureau of Mines has studied apparatus and procedure for the distillation analysis of petroleum, and this report is presented as a record of developments up to the present time. The work is incomplete, but the extensive information that has been obtained to date is made available as a guide in handling laboratory distillation problems. The analytical distillation of petroleum is commonly made to determine range of boiling points or to separate the oil. into fractions for detailed examination, or both. When only one of these two ends is sought the procedure involved is notably simpler than when, as is more common, information is required regarding both boiling range and properties of fractions. Moreover the degree of minuteness of measurement and the accuracy of the data required from analytical distillations differ considerably. Often the simplest sort of comparative figures are satisfactory; other tests require complicated and highly tedious procedure. No one distillation method is universally applicable, and it is impossible for anyone group of investigators to foresee all the different kinds of requirements that may occur in the industry.

Jan 1, 1922

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

By William F. Hahn

The Bureau Of Mines recognized the desireability of illuminating working places in trona mines. This report describes two illumination system designs, their demonstration and evaluation on a Jeffrey 120HR continuous mining machine in an active working trona mine in Wyoming.

Jan 1, 1980

By F. A. McLean

The past decade has witnessed a rapid increase in the number and variety of uses found for internal combustion engines in mining operations. Gasoline engines are now widely used for operating core drills, pumps, compressors, small hoists, switching locomotives, tractors, boats, and other equipment. The heavy-oil engine is employed for operating compressors, generators, shovels, ore-milling machinery, and- in the iron, copper, and coal districts- in connection with that' latest newcomer in modern railroading, the oil-electric locomotive. Each of these applications could well form a subject for a lengthy treatise in itself. This paper, however, will be confined to a discussion of some of the features of internal combustion engines as applied to mine compressing plants and mill drive. Perhaps at no time in the history of mining in Canada has the search for new mines been more vigorously carried on, more old properties rejuvenated, or more remote districts exploited than during the past three years. The mine operator of today has a far wider range of equipment and facilities at his disposal than had the pioneers of Rossland, Cobalt, or Porcupine. Each year now witnesses the hinterland driven farther and farther back as improved forms of transportation, machinery, and methods make possible the exploration of properties once considered too inaccessible to warrant serious attention. Howey, Sherritt-Gordon, Callinan-Flin Flon, Jackson-Manion, Picard Gold Mines, and a number of properties in British Columbia, afford excellent examples of work carried out on an extensive scale miles from a railway, or in comparatively inaccessible mountain regions.

Jan 1, 1928

By WM. H. RINKENBACH, C. A. Taylor

No complete work on explosives, their constitution and analysis, has hitherto been published. Several books that contain chapte.r;s on analysis do not cover the matter thoroughly. Methods tha;t, manu~ facturers, testing stations, and other . agencies have developed to meet their own requirements have not been made public. The Bureau of Mines has issued four publications 1 - cov:eri:ng special phases of the subject. This bulletin. is not inte.nded to replace those reports, but rather to cover present methods employed 'in the , industry and to include all classes of explosives and the materials used in their manufacture. No sharp distinctions can be drawn between classes of explosives. . Surplus military explosives, for example, may be used for blasting, just as blasting explosives, under some conditions, may be employed for military purposes. Moreover, one class gradually merges into another because of similarity in composition. Explosives are here grouped as dynamites, black powders, propellants, detonators, and primers. Some materials are used in practically all these groups ; others in only one. To discuss all the materials that have been or that may be used and the methods for their identification and quantitative determination is not feasible, but the methods described will probably suggest ways of examining new mixtures.

Jan 1, 1923

By B. W. Roberts, V. A. Phillips

A copper alloy containing- 25.5 at, pct Zn and 19.0 at. pct Ni, which was previously found to show an anoma1old.s hardening effect on quenching- from 600 "C and aging- at 400oc, has now been examined by neutron diffraction. No evidence of long-range order was found. The aged sample showed diffuse scattering- consistent with clustering. The anomalous hardening effect is now attributed to lattice strains caused by clustering rather than (long-range) order hardening. SOLID-solution Cu-Ni-Zn alloys (the commercial 'nickel silvers") have been reported to show anomalies in: change of resistivity on cold working,1-6 temperature coefficient of resistance,2-12 resistivity at low temperatures,13,14 parameter (vs temperature),2"4 calorimetric data,2,4 specific heat,15,16 dilation,2-4 and elastic modulus.17 The structure responsible for the anomalies is produced by annealing typically near 400°C and is rather loosely referred to as the ('K-Zustands" (K state), a term coined by Thomas1' who apparently meant simply that the arrangement of atoms on the sites deviated from that expected statistically. Thomas proposed that the K state occurred in a variety of (solid-solution) alloys such as Cu-Ni-Zn, Ni-Cr, Ni-A1, Ni-Cu, Fe-A1, and Fe-Si and is recognized because its formation is strongly temperature-dependent and results in an increase in electrical resistance which can then be decreased by cold working. Later workers on ('nickel silver" have interpreted the K state variously as short-range order, long-range order. or a combination. The present work was prompted by the discovery by Phillips and Jones19 of a substantial hardening effect when an 18 pct "nickel silver" alloy which is fairly close to the Cu2NiZn composition, was reheated in the range 150" to 450 C after previously quenching from 600°C or, alternatively. was slow-cooled from 600°C or above. The phenomenon was attributed to (long-range) order hardening. Due to the similarity in the atomic scattering factors of copper. nickel, and zinc atoms, the ''nickel silvers" are unfavorable for X-ray diffraction studies aimed at detecting ordering. Nevertheless Bialas et a1.,20 using a powder sample containing 47.96 wt pct Cu, 24.03 wt pct Ni, and 27.98 wt pct Zn, slow-cooled from 400" to 200°C taking 500 hr, observed weak super lattice lines. Further unpublished work" using an anomalous dispersion X-ray technique indicates that zinc atoms are regularly ordered at the corner points of the lattice cell, while the nickel and copper atoms are statistically distributed on the remaining sites. Köster 17 also observed X-ray superlattice lines, for example, in an alloy containing 43.5 wt pct Cu, 28.6 wt pct Ni, and 27.9 wt pct Zn superimposed on the basic fcc cell with a = 3.62 kX. He proposed a Cu3Au-type superlattice with the Ll2 structure in which the A sites were statistically occupied by copper and nickel atoms and the B sites by zinc. He adds that substitution must be possible so that zinc atoms partly occupy A sites. Below about 35 pct Cu, Koster had some evidence for a CuAu-type superlattice with the Llo tetragonal fcc structure with a = 3.82 kX, c/a = 0.88 which could be preserved by quenching. This is suggested17722 to correspond to CuNiZn. While the present work was in progress Hirabaya-shi et a1.23 made an independent comprehensive neutron-diffraction study of a single crystal containing 50.05 at. pct Cu, 26.57 at. pct Ni, 0.25 at. pct Mn, 0.13 at. pct Fe, balance zinc. The presence of manganese and iron is surprising since the crystal was supposedly grown from high-purity metals. The homogenized crystal showed evidence of long-range ordering after an anneal of 5 months at about 300°C. Three possible crystal models were proposed. A curious feature of their results23 is that they could not find any neutron-diffraction evidence of ordering in a powdered polycrystalline near-stoichiometric Cu2NiZn alloy. There appears to be some essential difference between a near-stoichiometric Cu2NiZn alloy and one somewhat further off stoichiometry as used by the present authors. Thus Sato14 was able to reproduce the low-temperature resistivity anomaly reported by one of the authors13 on the present alloy if he used a similar composition, but found the normal behavior of the residual resistivity in a near-stoichiometric alloy. satol2 found that the resistivity of a cold-drawn slightly off-stoichiometric alloy increased to a maximum on isothermally annealing at 300°C and then decreased ("over-aged"). Since he could not explain this on the basis of ordering phenomenon, he proposed that zinc atoms were segregating to stacking faults (Suzuki effect) and found etching bands on the surface by replication which were attributed to the widening of faults. Sato suggested14 that the hardening effect observed by Phillips and Jones19 is partly due to the Suzuki effect. EXPERIMENTAL The starting material was 1/4-in.-diam hard-drawn rod of a commercial 18 pct "nickel silver" alloy identical with that used in a previous study by Phillips

Jan 1, 1967

As the mining industry looks to new technologies for a safe work environment and increased production rates, so should emergency response teams when dealing with organisational incidents. Implementation of technology has transformed the nature of incidents within the international mining community with lower frequency, high impact events replacing high frequency, low impact incidents of the past. In turn the approach to mines rescue response and preparation has naturally diversified. New rescue technologies when applied effectively can only further advance preparation and the response of mine rescues teams. This paper discusses some of the changes associated with mines rescue as the industry embraces technology. It highlights some recent rescue responses and their approach and gives examples of some of the new technologies being used for improved mines rescue.

Jan 1, 2004