Search Documents

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By J. Y. Murdoch

TAXATION has become a major item in the operation of Canadian mines, and, as such, merits our most serious consideration. I feel it was a splendid idea for the Institute to set aside this time for a frank discussion of this important subject, and believe great benefit will result from a better understanding of the methods and underlying principles involved. Mining, as a great national industry, may quite properly be called upon to pay its fair share of the cost of running the country; and there is no tendency on our part to avoid this responsibility. There is, however, a very definite demand that the proportion be just, and fairly and sensibly applied. I believe that Mr. C. G. Williams, Secretary of the Canadian Metal Mining Association, and others, are giving details of the various Provincial and Dominion regulati6ns, so I shall not touch on that phase of the situation. However, there are some important factors to which I should like very briefly to call your attention. The first is the vital need for stability. As you all know, a considerable period must elapse between the preliminary stages of any mining venture and the time when it comes to production-or is finally abandoned as un-profitable. These early days are fraught with many unavoidable uncertainties. If, to these natural hazards, the apprehension of instability of governmental action be added, the risk becomes so great that capital seeks other and safer fields for investment, and many otherwise promising projects are thus discarded. There probably never has been a time in recent years when so much money was seeking investment as now. Under favourable conditions, the development of our great mineral resources would be a natural and attractive outlet for this money. The amount of taxation which the mining industry can properly absorb is of the utmost importance at this time, and it might be well to consider this question in its relation to the economic stability of our country, for it cannot be too greatly emphasized that direct taxation is only one item in the net return which our governments derive from the mining industry. Indeed, the many indirect benefits are so manifest that it would seem almost unnecessary to enumerate them! We almost invariably think of mine taxation as a direct company tax-overlooking the fact that sales tax, customs duties, acreage tax, income tax on mine dividends, foreign shareholders' dividend tax, and others, must all be taken into consideration. It would seem that the economic value of non-ferrous metal mining in Canada is not sufficiently understood and appreciated.

Jan 1, 1935

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"Drill and blast represent the most important, and sometimes the costliest processes in the mine. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum and Temeng, 2015). The use of available information to improve the drill and blast processes can be the difference between a wasteful process and one that is optimized for costs, safety and desired fragmentation. Mining operations have access to several types of data sets that include a variety of different systems. This information can be used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the drill and blast process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting across multiple sites, it becomes valuable to create auditable, automated and sustainable workflows for handling the information.In some cases, the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Wixom, Watson, 2007). The author’s initial implementation plan for the drill and blast solution included using data stored at the sites on local servers. However, we learned early in the process that much of the work for aggregating and supplying the required data was already completed and was available in the EDW ready for use. This saved time, reduced risk and added value to the system.The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, especially highlighting the value of using an EDW for managing drill blast information; and to discuss how technical challenges encountered during the implementations were resolved. This article targets users that want to better manage their drill and blast data or try to set up standardized workflows for using this information.This case study will discuss the process of implementing a drill-and-blast workflow at multiple sites within Freeport-McMoRan (FMI) using both data at the sites and information available from the EDW."

Jan 5, 2017

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By B. McCosker

The choice of the appropriate delivery process for a project is often not adequately thought about. The industry needs to be prepared to break its preconceived mind-sets on delivery procedures. Industry should also be prepared, on a project by project basis, to commit to a critical review as to how the assessment and then selection of the best procurement method can best optimize the project outcome for both client and contractor. Conventional standards and biased reliances and experienced based preferences should be challenged. To achieve this requires a paradigm shift in attitude to both the process of tendering and the evaluation of tenders. Tender and contracting practices are dynamic and have moved away from solely cost based assessments. Tendering contracts arise imposing changed duties upon owners. Traditional contract delivery models have shifted, reflected in part by the trend towards relationship contracting. The categories of contract options are not closed. Many are but hybrids of other time-tested models. This paper considers options available for any brownfield or greenfield project. The principles outlined are translatable to supply, upgrade, operation and maintenance arrangements.

Jan 1, 2002

By T. G. Hawkins, T. M. Naciuk

"The Katie Cu-Au deposit is situated in southeastern British Columbia, 425 km east of Vancouver. The deposit is a member of the alkaline group of porphyry Cu-Au deposits associated with potassically and propylitically altered andesitic volcanic rocks.The Katie porphyry system occurs in mafic to intermediate alkaline volcanic rocks of the Lower Jurassic Elise Formation of the Ross/and Group. Host metavolcanic rocks include andesitic to basaltic flows, flow breccia, massive fine tuff and crystal tuff Gabbroic intrusions alternate with the volcanic rocks in drill core. The lack of chilled margins and shear contacts, as well as their similar composition to the volcanic rocks, suggest that the gabbro was synvolcanic.Alteration exhibits a zonal pattern spatially related to zoned porphyry-style mineralization. Propylitic alteration is common and assemblages consist of epidote, chlorite, sericite and calcite. Potassic alteration zones are accompanied by elevated copper-gold grades and are composed of K-feldspar, plagioclase, quartz, biotite and chlorite. Narrow drillhole intervals of secondary magnetite, generally less than 2 m across, occur above the potassic alteration zones. A thick oxidized cap lies above the mineralized zones, although only local supergene enrichment has been identified. The lack of supergene enrichment is perhaps due to intense near-surface fracturing and leaching from a high energy groundwater environment.Sulphide mineralization consists mainly of pyrite within the propylitic halo, and pyrite and chalcopyrite with trace pyrrhotite, sphalerite, tetrahedrite, bornite and molybdenite within the potassic alteration core. Malachite, azurite and traces of chalcocite occur within the oxidized cap.Discovery and exploration techniques have included airborne geophysics, regional stream sediment sampling, prospecting, geological mapping, ground geophysical surveys, soil sampling surveys, and diamond drilling. Two primary targets of porphyry copper-gold mineralization have been identified by exploration. The Main zone strikes northwest, has an apparent true thickness ranging from 70 m to 135 m, and is a minimum of 500 m in length. The 17 zone strikes northwest, has an apparent true thickness of 90 m, and is a minimum of 300 m in length. The two zones are defined by grades that generally exceed 0.2% Cu and 0.25 g/t Au. Both zones are open along strike and to depth."

Jan 1, 1995

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By Grant R. Brown

The report provides guidance for determining those environmental impacts associated with the surface mining of steeply pitching coal seams. In addition to the environmental impacts, four additional issues are addressed, namely (1) Time and motion studies of those coal mining systems employed in mining seams which pitch in excess of 250, (2) Assessment of those mining techniques, (3) Development of rationale for the mining methods employed, (4) Identification of the reclamation practices and determine whether these practices were in compliance with appropriate Federal and State regulations. Five surface mines located in three geologically distinct basins of the United States were analyzed during the period of August through November 1979. The three basins include the Hanna Basin of Wyoming, the North Park Basin of Colorado and the Southern Anthracite Field of Pennsylvania.

Jan 1, 1980

By J. E. Nesset, L. S. Urbanoski, J. R. Goode

"The benefits and advantages of pre-competitive, collaborative industry/university research are not always well appreciated. This paper presents the case study of a current collaborative project between CAMIRO-Metallurgical Processing Division and McGill University that is investigating the understanding and prevention of sphalerite activation in lead and copper-lead flotation circuits. The benefits of the research findings to the sponsors can be maximized by an approach which links the researchers themselves with the sponsors at frequent, interactive project review sessions. Some examples of the findings and their application to industry are also presented along with a general update on CAMIRO-MPD.INTRODUCTIONThe history of Canadian efforts in the area of collaborative pre-competitive research is not long when compared to Australia (AMIRA) and Britain (MIRO). AMIRA (Australian Mineral Industry Research Association) began over 40 years ago and has had a well recognized role in bringing together industrial sponsors and researchers to fund a large variety of very significant development projects in that country, The total AMIRA funding effort for mineral processing work currently exceeds some $Aus 40 million with new projects valued at about $Aus 12 million initiated each year. This high level of commitment by industry has contributed to establishing Australian researchers and their facilities as among the best in the world.Canadian companies have traditionally funded much of their R & D in-house with extensive facilities and large funding commitments. The past 2 decades have seen most of these facilities disappear. The current situation is one in which only the largest integrated metal and mining companies have retained their own R & D groups (e.g. INCO, Falconbridge, Noranda). Industry-funded research at universities was primarily through individual efforts by the mining companies and rarely included collaboration with other mining companies, equipment or chemical suppliers, or engineering firms."

Jan 1, 2001

By N. Sasto, E. Bondi, G. R. Lane

Cyest Corporation has been involved in economic modelling and optimisation with various mining clients within South Africa, and internationally, for the past 5 years. In the mining industry in particular, the relationships between variables that are controllable, and those that are not, and the physical and economic outcomes are complex and often non-linear. These relationships constitute an economic system. In the mining context, although many of the relationships can be accurately quantified on a ?single variable to single variable? basis, such simplistic relationships will not suffice in order to understand the dynamics of an entire mine. One has to specify and quantify the relationships between hundreds, if not thousands, of variables. Furthermore, in reality, these relationships change over time. This is the role of an economic model where all the relevant cause-effect relationships, within pertinent constraints, are accurately represented. Models that are used for optimisation must therefore capture the dynamics of the economic system in question as well as anticipate changes to the relationships between these variables. An accurate economic model is a prerequisite for successful optimisation. Optimisation entails the allocation or configuration of resources, within control of management, which will maximise (or minimise) a desired objective function. An optimal configuration (implying trade-off) of controllable variables therefore exists for a given set of assumptions that will yield a maximised objective function. Due to the multi-variant trade-offs required for optimisation, the concept of the ?Economic Surface? or ?Hill of Value? has been used to represent these optimisation outcomes and to discern the route to an optimal configuration. A good example of this is the volume versus cut-off grade trade-off that yields an optimal value for a particular shaft with its unique geological and economic assumptions. More recently, Cyest has extended these economic models to incorporate risk associated with variance in assumptions and inputs. This is termed DFA (dynamic financial analysis) and incorporates stochastic modelling and some of the latest actuarial techniques around modelling global assumptions (such as pricing and exchange rate). This paper will cover the theory around mine optimisation through some example case studies, and also explain the latest thinking regarding incorporating DFA.

Jan 1, 2007

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By AIME AIME

WAR undoubtedly accelerates metallurgical progress, although its most obvious effect is a tremendous waste of materials. The necessity for restrictions in normal uses of metals results in a search for substitutes or for enhanced properties that will make a limited supply last longer. An insatiable demand for more metal to be produced more quickly favors trial of new processes, new metallurgical tools, and new methods of fabrication. Greatest advance is made, of course, in practical physical and process metallurgy. Theoretical or fundamental research necessarily must take a secondary position, and is so regarded in this review. It is not that developments in theoretical physical metallurgy are lacking entirely, but, following the same trend noted in other countries as they entered war activities, attention in the U.S.A. has been shifted strongly to those developments having an immediate practical application.

Jan 1, 1943

By F. G. Hyde

Passage of the Public Utilities Regulatory Policy Act ("PURPA") in I 978 created an entirely new industry that is referred to today as the Independent Power Producers ("IPP"). Requirements of project owners, environmental compliance, project design, the financial community and most of all, the need to be a low-cost producer presented a unique situation for the sourcing and the utilization of fuels. Depending on the specific type of project being developed, (e.g. coal-fired, wood/biomass, natural gas, petroleum coke or a blend of several fuel types) and the type of boiler design, it is important to acquire fuels that will optimize both the project's operating efficiency and flexibility. This paper will focus on the acquisition of fuel for coal-fired projects, but will describe the necessary steps in the sourcing, contracting for, and the utilization of fuels and transportation resources in the IPP industry today.

Jan 1, 1996

By Jennifer Riefenberg

Research efforts by the U.S. Bureau of Mines include running a series of displacement-discontinuity, boundary-element models to simulate the gateroad design at an underground coal mine in northwestern Colorado. The initial mine design is a yield-abutment chain pillar arrangement in a three-entry, longwall gateroad system. Pressure effects from mining the first and second panel were recorded using borehole pressure cells (BPCs). These field data were then compared directly to the model output. Observed yielding in the field was approximated by reducing material property values and/or removing pillar elements in the model. Model results using this calibration technique mirrored the field measurements consistently. Using the calibrated model parameters, a suite of models was run simulating an experimental entry design: exchanging the yield and abutment pillar locations. These model results reflect a 20¬to 33-percent reduction in core stresses in the yield pillar during mining of the second panel. Improved pillar and entry conditions are suggested by these predictive results. The design modifications were then implemented at the mine along a 150-m (500-ft) test section. Field observations and measurements from the experimental design test site compared favorably with trends of the model predictions.

Jan 1, 1993

By G. Warren

"In the past, smelting and refining of the precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. This philosophy is changing however, as economic and environmental pressure are forcing a re-evaluation of all aspects of gold mining and milling.This paper describes and evaluates three furnace technologies available and used by precious metal operators. The operation of arc, induction, and reverberatory furnaces are discussed and their strengths and weaknesses with respect to capital cost, impurity removal, slag quality, and environmental concerns highlighted.INTRODUCTIONIn the past, smelting and refining of precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space, and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. Generally, gold producers will spend a great deal of effort to squeeze the last drop of efficiency out of a leach or grinding circuit via simulation or testwork but will design and build the refinery based upon past practices or industry standards. That past practices or industry standards will provide a functional refinery is undisputed; that this philosophy achieves the efficiencies that are possible or demanded in other plant operations is debatable.Environmental and worker hygiene requirements are considerations as well. Pollution control equipment can become a substantial contributor to both the capital and operating costs of a refinery and furnace selection has a marked influence upon the type and cost of this equipment. Slag characteristics and subsequent processing options available also play a role in furnace selection as precious metal slag losses and the recovery effort can greatly influence the cost / benefit analysis of a particular technology."

Jan 1, 2001

The National Economic Viewpoint? Any substantial project undertaken by private enterprise would normally be subjected to a Discounted Cash Flow analysis of its commercial viability, and would proceed only if the rate of return was judged satisfactory. A 'national viewpoint' analysis attempts to do the same but from the viewpoint of the community as a whole. The objective is to ensure that those projects are undertaken which yield the best return, economic and social, to the nation as a whole.

Jan 1, 1984

By G. J. Perrott, H. W. Clark

During the course of the cooperative smoke abatement investigation carried on by the Bureau of Mines , the city of Salt Lake and the University of Utah during 1919-1920 , a study was made as to the suitability of Utah coals for by-product coking with particular reference to low temperature coking . was done because it was realized that a smokeless fuel for domestic consumers was the best remedy for this class of smoke producer . A report of the technical side of the work was included in the final report of the cooperative investiga- Since this report was written (June 1 , 1920) further work has been done by other investigators .

Apr 1, 1922