Search Documents

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By J. B. Cheung

The results of a program to demonstrate the technical feasibility of hydraulic borehole coal mining are presented in this report. The hydraulic borehole method of coal mining involves inserting a hydraulic mining device into a borehole that has been drilled from the surface into the underground coal bed. The borehole mining device issues a jet of water under high pressure, which breaks the coal. These pieces of coal, along with the water, form a slurry, which flows to the base of the borehole where it is pumped to the -surface. Phase I of the program encompassed the design, fabrication and factory-testing of a hydraulic borehole mining device. The program was successfully completed with the field tests being conducted at the Wilkeson-Carbonado Coal Field near Wilkeson, Washington. The technical feasibility of hydraulic borehole coal mining was demonstrated by mining 32 tons of coal at a depth of about 75 ft over a period of 4 hours.

Jan 1, 1976

By G. M. Kintz

It is estimated that 10,000 lives were lost and $285,000,000 worth of property was destroyed by fire in 1937. Of the 103 fatalities in tie petroleum industry in 1938, 36 resulted from fires and explosions.3/ Everyone can help to prevent the tremendous losses, both in life and property, caused annually by fires and explosions, Forest fires occur every year, in which the tremendously intense heat wave ahead of the flame turns beautiful green trees into blazing torches like so much gasoline, vapor, and jumps over the tops of trees to start fires behind the firs fighters; prairie-grass fires occur, and a farmer in the path of the fire must plow a furrow around his home and outbuildings before the flame reaches them; and frequently automobiles are burned up in filling stations. Persons who have witnessed such sights know better than to throw a lighted match, cigarette, cigar, or hot coal from a pipe out of an automobile or to discard a fire or flame of any type in the forest, in the country, or in the city.

Jan 1, 1941

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

The current mining operations at Newmont Boddington Gold Mine (NBG) commenced in 2008, and commissioning of the processing plant started in the latter half of 2009. Metso Process Technology and Innovation were engaged to assist NBG with commissioning and project ramp-up through the implementation of a comprehensive ?Mine-to-Mill? Process Integration and Optimisation project. This methodology entailed extensive data collection which included drill and blast audits, ore characterisation, comprehensive comminution circuit surveys and review of operational data to assess the limitations within the current mining and processing operations. The results of these investigations have been used to define the operating base line of both the mining and processing areas and identify improvement opportunities. The use of modelling and simulations, utilising actual production data, has allowed for multiple scenarios to be evaluated, minimising the requirement for actual trials and thereby minimising impact on the operation. Improvements implemented to date include: the introduction of routine rock strength measurement for inclusion in block models, modifications to blast design improving ROM fragmentation and downstream comminution process performance, and changes to improve performance of secondary crushing and grinding circuits. Close cooperation between the mine and plant personnel is playing a significant role in overcoming the challenges presented to this operation and further improvements are targeted for the second full year of process plant operation.

Jan 1, 2012

By William Hissem

When we look out on our business landscape today, the words higher, faster, fdwther come to mind. Compliance issues, business integration, increasing production and profitability demands are converging in an age old industry and giving it a new twist. Not that the rock changes, rather that as the variables of our business change, the resulting “cut-off grade in business” turns ore into rock or rock into ore. The trick is to emphasize the latter. As with the miners of yore, what was recovered from the business enterprise had a lot to do with tools and skill. So it is today. When the casual observer looks at drilling and blasting operations today, many see the same basic offering in terms of equipment types and process. Looks, however, can be deceiving. As with the aviation sector, a given machine might took similar to previous generations of equipment, but in fact is radically different in terms of power, efficiency, accuracy, and range. So it is with hydraulic top-hammer drills today.

Jan 1, 2000

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Thien Sok, Yaojun Lu, Craig Gilbert, Jeremy Scott

Feedwells play a pivotal role in gravity thickeners, governing flow distribution, feed dilution, and flocculation condition during solid–liquid separation. This study presents an optimized design and digital prototyping framework for FLSmidth’s E-volute and E-Duc Feedwell systems, integrating advanced computational fluid dynamics (CFD) with quantitative criteria introduced at SME2024. Building on established FLS technologies, a series of novel configurations were developed and systematically assessed under full-scale and site-specific conditions. CFD provided quantitative insight into flow distribution, feed dilution, and flocculation efficiency, enabling iterative refinement of design parameters. The optimized feedwell demonstrated superior hydraulic performance, enhanced mixing, and improved flocculation outcomes. Beyond the specific design advances, the work highlights CFD as an effective and economical tool for digital prototyping, facilitating early identification of design limitations, reducing dependence on physical trials, and accelerating innovation. The methodology underscores the value of simulation-driven design in advancing feedwell performance and improving thickener technology.

Feb 22, 2026

By Frank G. Wickert

One key to maintaining successful mining operations in today?s global economy is in having the ability to access real-time machine operating data ([1] G. Brown, B. Ebacher, W. Koellner,2000)([2] Brochure of Siemens E&A, Order Number 141000-1). With recent and ongoing advances in mining equipment systems it is imperative that mine managers have full knowledge of the status of their equipment at any given point in time. This knowledge is critical to ensuring that the productivity of each and every machine is maximized. Knowledge of machine status is only the first step, however, in controlling and optimizing a piece of mining equipment. Computer based diagnostic systems, traditionally offered on mining equipment, have provided a link for collecting data and trouble-shooting problems as they occur. One problem existed, though, that those systems stopped short of providing full drive systems access. A maintenance technician could see the data but to make critical adjustments or make repairs the technician needed to be on the machine. In extreme cases the machine would be down until OEM assistance could reach the mine site. The key then to reducing down-time and maximizing machine productivity was creating a system that could not only monitor drive systems but also provide remote access to those systems. Essentially a link needed to be created through which a technician could gain drive access remotely then make adjustments or repairs without being on the piece of equipment. This paper will introduce AccessDirectTM, a new remote diagnostic system for Bucyrus mining shovels and draglines. AccessDirectTM combines all three important elements of remote diagnostics: ? Vital Signs and Production Monitoring (SiRAS-M) ? Automatic analysis (SiRAS-A) of faults, and tracking of trends for preventive and reliability centered maintenance , and ? Fast, direct Intervention (SiRAS ? I) for troubleshooting support, repairs, and system optimization.

May 1, 2002

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By Bujtor G. J, McMahon D. W

This guide to the understanding of ore reserve estimation is the revised version of a report with a similar title circulated within the CRA Limited (CRA) group of companies in mid-1980. It is the principal result to date of an Ore Reserve Study commissioned by CRA in late 1977.This guide to the understanding of ore reserve estimationis the revised version of a report with a similar titlecirculated within the CRA Limited (CRA) group ofcompanies in mid-1980. It is the principal result to dateof an Ore Reserve Study commissioned by CRA in late1977.The study was prompted by two ore reserve situations.The Zinc Corporation and New Broken Hill Consolidated,Broken Hill, had reached the point of havingto find a replacement 'for their traditional ore reserveprocedure and Mary Kathleen had to admit publicly thatore reserve predictions would not be realized. Thesewere not however the only problems to be looked at. Asmentioned more fully later, other ore reserve situationswere known, or were met during the study, in copper,gold and nickel as well, where poor realization: expectationratios had ranged from embarrassing to disastrous.These made it clear that ore reserve estimation had to belooked at afresh.The fresh look has resulted in a broadening of theconcept of ore reserve estimation from its traditionalpurely computational basis to an approach embracingall the many things that can affect expectation andrealization as essential factors. Hence this guiderepresents a gathering together of what has been learnedand what should be known to all those concerned withore reserves in any of its diverse aspects.The study has been marked"by a number of changesof thinking. At first the aspects that appeared to requireattention were two; recognition that an ore reserve statementwas an estimate, not a precise calculation; and asearch for im improved estimation procedure adapted tolow grade ores with narrow economic margins. Threeyears later the view was that the need was to incorporateinto ore reserve estimation all relevant aspects of theproposed mining operation from choice of a samplingmethod to sales contract specifications.This study is thought to be unique in being frankabout weaknesses in ore reserve estimation and intreating failures not as natural disasters (like drought orflood, which have to be endured) but as potentiallyavoidable. It has led to three principal conclusions.

Jan 1, 1982

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP.Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, OOP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the OOP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By Vincent Roy

Numerous on going activities at the Daniel-Johnson Dam : ? Surveillance / monitoring ; ? Structural investigations & evaluation ; ? Injection work ; ? Crack mapping ; ? Instrumentation management (drawings & inventory) ; ? Drainage system state ; ? Foundation evaluation

Aug 1, 2013

By Shichang Liu, Hongli Jia, Zhaolian Wang, Maotang Liu, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce and promote a latest technology and equipment for magnetite. It’s featured of purifying concentrate, lowering tailing grade, high concentrate recovery rate and stable operation. HUATE® New Style Elutriation Electromagnetic Separator is an equipment to obviously upgrade magnetite. The slurry is fed into separation area through feeder. Generated by excitation coil, the working magnetic field distributes specially in separation area. Under the combined effect of the background field, excitation and demagnetic field and gravity, the mineral particles float downwards in the form of magnetic chains, and interact with the rising water. The gangue, non-magnetic particles, lean intergrowth,etc will be discarded as tailing via overflow tank and pipe. While the magnetic will be discharged from concentrate pipe. Its grade is 2%-10% higher than that of traditional magnetic separation equipment. It adopts the technologies of transformer oil cooling, alternative and uniform pulsation magnetic field controlling the tailing grade, larger drum feed-in device, more uniform umbrella scattering discharge and stabler output current, and realizes lower coil temperature raise, stabler magnetic field, more uniform discharge, effective isolation of weak-magnetic area from non-magnetic area, more obvious upgradation and recovery rate and lowering tailing mFe%. It’s more suitable to purify and thicken the high grade and ultrafine iron powder. Compared with traditional elutriation equipment, it adopts new technologies in removing impurities, operation, large-scale, process simplification, water-saving, remote control, etc. It optimizes the comprehensive beneficiation index, expands its application scope, reduces resource wastes and increases economic benefits.INTRODUCTIONMagnetite accounts for a comparatively great proportion in various iron resources. As it’s a kind of strong magnetic mineral, we must adopt the weak magnetic separation equipment in magnetic separation process to realize removing Si and lowering impurities. While it cannot do very well to use the common weak magnetic separation equipment in the final cleaning to remove Si and lower impurities. At present, the plants, adopting single magnetic separation process to realize cleaning and removing Si and lowering impurities, are in the minority. Most magnetite plants adopt the flotation separation process to remove Si, lower impurities and purify the concentrate. Though with stable indexes and high Fe recovery rate, the flotation process is very complicated, high-cost and with lots of environmental pollution. If adopting the weak magnetic separation equipment can realize removing Si, lowering impurities and the final cleaning, the magnetic separation process should be the primary choice."

Jan 1, 2016

By J. Daavittila, P. Jokinen, M. Honkaniemi

In the latter part of the 1980?s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation an application for FeMn production was developed. Now when Tornio FeCr-plant is considering the expansion the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand of better working conditions. The possibilities to respond to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control of the process even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Magnos Marinho da Silva

A Metalurgia do Pó é um processo de conformação mecânica com um grande crescimento de sua aplicação no cenário industrial brasileiro, por possuir um vasto campo de aplicação que inclui, por exemplo, a fabricação de componentes automotivos, eletrodomésticos, ferramentas de corte e ferramentas elétricas. A sinterização é a fase mais importante do processo, no qual o pó já compactado é submetido a uma temperatura abaixo do seu ponto de fusão, obtendo como resultado um material com excelente acabamento, precisão dimensional e propriedades mecânicas. O trabalho apresentado tem como objetivo avaliar o comportamento do composto intermetálico denominada de Al12Si com a composição de 12% de Si, 1,14% de Ni; 1,08% de Mg; 0,45% Fe; 1,08 % de Cu e Al em balanceamento. Foi sinterizado com gás argônio para fazer um comparativo do mesmo material, porém utilizando uma atmosfera de nitrogênio. Tendo como objetivos específicos realizar levantamentos sobre a densidade, microdureza e metalografia apresentados em função das cargas aplicadas em cada uma das amostras. Comparar a influência do tratamento térmico T6 na dureza dos materiais em função da atmosfera de sinterização. A metalografia apresentou porosidade inerente ao processo, mas houve um acréscimo de microdureza entre as amostras produzidas em atmosfera com argônio e as produzidas com atmosfera com nitrogênio com uma variação de 59,51 HV-50g. para 72,30 HV-50g.

Aug 17, 2017

By James F. Archibald, H. Jame Hackwood

"Research was performed to assess the feasibility of barrier membrane substances, for use within mining or associated high risk environments, in restricting the diffusion transport of radon gas. Specific tests were conducted, both within laboratory and in situ environments, to determine radon gas concentration ratios across a barrier of interest and emanation rate variation resulting from application of such materials. Several materials have been demonstrated to be effective in restricting the emanation of radon gas into initially radon-free environments. One liquid material shows particularly good promise upon consideration of ideal radon barrier criteria.IntroductionIt has long been known (I.2.3) that inhalation of the short-lived, alpha particle-emitting daughters of radon gas can result in irradiation of lung tissue with the potential for causing lung cancer. Control measures are necessary to maintain concentrations of airborne contamination at a minimum to protect miner health and safety. Typical control practices in mines have been through the application of systematic ventilation and backfilling of excavated opening. As mines become deeper, however, and additional workings become exposed, increased ventilation capacity requirements are needed. As an alternative to other radiation control measures, the use of sealants to prevent radon migration from walls into mine atmospheres may provide a suitable engineering alternative."

Jan 1, 1987

By H. M. Woodroffe, H. K. Conn, S. J. Rice

World production of asbestos is estimated to be at a current level of almost 3.5 million tons, having more than doubled in the past ten years. A substantial part of the increase has been due to a rapid expansion in the Soviet Union. Production from that country during 1964 is estimated at 1.5 million tons and, as a consequence, Russia has displaced Canada as the leading world producer. Although traditionally the asbestos mining industry has been centered near Sverdlovsk in the Urals, two new producing areas have been under development for some time. It is expected that a new mine will be in operation in 1965 near Kiembi, Kazakhstan, some 300 miles south of Sverdlovsk, and an- other mine at Aktrovak in Tannu-Tuva, west of Lake Baikal. These developments will provide a significant increase in the production capability of Russia. Although internal consumption is expected to increase with the addition of new asbestos- cement producing facilities now under construction in Russia, there is some speculation that exports will also increase.

Jan 2, 1965

By James J. Dowd

During and immediately following World War II, the heavy demands for steel required the mining of unusually large quantities of coal for the manufacture of metallurgical coke. The largest demand for metallurgical coke is in the Appalachian region, which comprises central and western Pennsylvania, Maryland, West Virginia, Virginia, eastern Kentucky, Tennessee, and Alabama. This demand is satisfied by coke made from coals within the region; consequently, the reserves of coking coal in this region are being depleted more rapidly than reserves in other coal-producing regions. The supply A' high-quality coking coal during the war was inadequate, and some coke were forced to use inferior coals. The coke produced from these inferior coals adversely affected the rate of production. Another national emergency probably would produce a similar condition, and in the interest of -national security, the Munitions Board of the National Military Establishment requested the Bureau of Mines to evaluate the reserves of coals suitable for the manufacture of metallurgical coke. All bituminous coals in the Appalachian region are coking, and as the coal that produces the better metallurgical coke become depleted, other coal previously considered inferior will be used. The general trend is toward the use of lower-quality coals for metallurgical purposes.

Jan 1, 1950