Search Documents

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

By L. Schernikau, W. H. Smith

Oil, coal, and gas account for approximately 80% of global primary energy, but only a portion of total airborne CO2 eq (approx. 35% at GWP20 to 65% at GWP100), even though they account for 95% of total measured CO2 emissions. The benefits of these energy sources, as well as their related costs, are not all incorporated in current energy policy discussions. Global greenhouse gas policies must include documented changes in measured airborne CO2 eq to avoid spending large amounts of public funds on ineffective or sub-optimal policies. The authors examined airborne CO2, which is less than half of emitted CO2, as well as reported CH4 emissions and the global warming potential of CH4 as published by the IPCC for coal and natural gas. The surprising conclusion is that surfaced-mined coal appears ‘better for the climate’ than the average natural gas, and all coal appears beneficial over LNG. Therefore, current CO2-only reduction policies and CO2 taxes are leading to unintended consequences and the switch from coal to natural gas, especially LNG, will not have the desired impact of reducing predicted future global warming; in fact, quite the contrary. A large portion of anthropogenic global warming is attributed by the IPCC and IEA to CH4, but it must be noted that CH4 emissions from natural sources and from agriculture account for approximately 40% and 25% of annual global CH4 emissions respectively. Energy accounts for about 20% of documented CH4 emissions. CO2 contributes only approximately 35% of annual airborne anthropogenic GHG emissions after accounting for CH4, over a 20-year horizon. At a 100-year horizon, the contribution of CO2 increases to approximately 60%. Energy policies that do not consider all GHG emissions along the entire value chain will lead to undesired economic and environmental distortions. All carbon taxation and CO2 pricing schemes are incorrect and need to be revised. At IPCC’s GWP20 an approximately 2%1 higher loss of CH4 across the value chain prior to combustion of natural gas versus coal will lead to ‘climate parity’ of coal with natural gas. According to public data, natural gas value chains have high CH4 and undocumented CO2 losses. On a global average, using only IEA-documented CH4 data, natural gas emits approximately 15% more CO2 eq than surface-mined coal, over a 20-year horizon. This difference will increase as the use of shale gas and LNG expands. Investors should support all energy systems in a manner that avoids an energy crisis, including intermittent renewable energy systems where they make sense. If CO2 emissions need to be reduced, one of the most effective ways would be to install ultra-supercritical power plants with CCUS technology. However, the undisputed benefits of increased CO2 concentrations in the atmosphere because of its promotion of photosynthesis and plant growth effects (fertilization) need to be considered in energy policy decisions as well. The authors suggest that future research and development should concentrate on reducing net emissions from fossil fuel power plants and providing cost-effective and reliable new conventional power generation capacity, utilizing clean coal and clean natural gas technology.

Mar 2, 2022

By W. Hustrulid

"In recognition of his inspiring dedication to the mining industry through education, research contributions and dissemination of practical knowledge, exceptional leadership and excellence in mining engineering practice and for his lecture, “You can't make a silk purse out of a sow's ear.” Recipient of the 2002 D.C. Jackling Award Introduction It is always difficult to decide on the most appropriate title to give to a paper or talk. It is a particularly difficult decision in the case of the Jackling Lecture, because the title becomes part of the award citation. I hope that the significance of this unusual title will become crystal clear as you read the pages that follow. However, to assist you in this journey, I will provide the following few words of guidance. In making a cake, you need the proper ingredients. If one or more of them are missing, it will not be a cake. In addition, the quality of the cake depends on the quality of the ingredients. In my lecture, the "cake" is the U.S. mining industry of the future. A national perspective President George W. Bush in his State of the Union Address (Bush, 2002) delivered on January 29, 2002, defined three national objectives: •win the war on terrorism, •protect the homeland and •revitalize the economy. Under the heading "revitalize the economy," he indicated the importance of "good jobs" and "energy production" by saying: "Good jobs begin with good schools. Good jobs also depend on reliable and affordable energy. This Congress must act to encourage conservation, promote technology, build infrastructure and it must act to increase energy production at home so America is less dependent on foreign oil." I wish that he would have broadened his focus and stated instead that: "This Congress must act to encourage conservation, promote technology, build infrastructure, and it must act to increase materials production at home so America is less dependent on foreign sources." With regard to jobs, all jobs are not equal. To paraphrase John Reeves of MidContinent Resources (Reeves, 2002): "If our nation is to prosper, we all cannot make a living by doing each other's wash. Some of us, at least, must be actively engaged in the primary production of raw materials from the riches of the earth and other Americans must turn those materials into consumer products." The unfortunate trend in our country has been to neglect the primary production of basic materials, even those coming next in line. We have left those responsibilities to others while we concentrate instead on performing various services, i.e., doing each other's wash and flipping burgers. This cannot continue. It must be remembered, especially by those in leadership positions, that all "jobs" are not created equal. Some jobs are much more essential to the security and wellbeing of our country than others. We must be sure that the important ones are in place. We cannot produce the basic materials that our nation requires without access to those materials. This leads to my Proposition 1: You cannot have a viable mining industry without a clearly enunciated, positive U.S. materials policy. Background regarding U.S. materials policy Resources for freedom. In January 1951, President Truman created the President's Materials Policy Commission, with William S. Paley as chairman. As expressed in the invitation letter from the president to Paley: This commission, within the executive office of the president, is to study the broader and longer-range aspects of the nation's materials problems as distinct from the immediate defense needs. The task of the commission is to make an objective inquiry into all major aspects of the problem of assuring an adequate supply of production materials for our long-range needs and to make recommendations that will assist me in formulating a comprehensive policy on such materials. The commission should study, together with any other aspects deemed by it to be pertinent, such questions relating to production materials as: - the long-range requirements outlook; - the long-range supply outlook; - the prospect and estimated extent of shortages; - the consistency and adequacy of existing government policies, plans and programs; and - the consistency and adequacy of private industry practices.

Jan 1, 2003

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By M S. Reston

The Tonkolili banded iron formations (BIF), Sierra Leone, host extensive iron ore deposits which are of economic signifi cance to the seaborne iron ore trade. The deposits are dominated by a strategic JORC compliant mineral resource of 11.6 Bt grading 30.1 per cent Fe comprised of primary magnetite mineralisation in the form of a fresh metamorphosed BIF featuring a uniform mineral assemblage of quartz-magnetite ± ferro-silicate minerals. Pilot plant metallurgical test work has demonstrated that the production of a magnetite concentrate is achievable using the established beneficiation techniques of magnetic separation and flotation. The concentrates arehigh-grade, and suitable for blast furnace or direct reduced iron pellet feed. The major challenge facing the development of such magnetite deposits at industry competitive production rates is the significant capital investment required for process plant and associated infrastructure.Two well-developed weathering zones exist within the deposits, and are associated with the progressive development of a tropical weathering profile overprinting the primary BIF. These zones feature a near surface hard indurated duricrust up to 60 m thick, and a soft progressively developed saprolite between duricrust and fresh BIF. These zones have been found to be amenable to producing iron ore products including DSO lump and sinter fines from the duricrust, and concentrate from the saprolite. Mineral resources sufficient to support commercial production of such iron ore products were defined by an intensive exploration program in 2010.African Minerals Limited has developed a three phase production strategy to progressively self fund the development of the Tonkolili strategic magnetite project by:• commencing a Phase I 12 Mt/a DSO operation in Quarter 4 2011,• increasing production in Phase II to 35 Mt/a with the commissioning of a saprolite beneficitation plant and associated infrastructure upgrades, and• developing a 45 Mt/a Phase III operation producing high-grade magnetite concentrate.The comparatively low capital and operating costs of a duricrust DSO lump and sinter fines operation coupled with its proximity to ground surface make it highly attractive for the generation of early cash flow for the Tonkolili project. Revenue from this early production may be used to selffund the subsequent development of phases requiring progressively more significant beneficiation plant and infrastructure.

Jul 11, 2011

By P. M. Ambrose

This report describes an accident, which took place in the Chemical Corrosion Laboratory at the College Park, Md., Station of the Federal Bureau of Mines. The accident occurred while Walter L. Acherman, chemist, was performing a routine manipulation during a corrosion experiment involving commercially pure titanium and red-fuming nitric acid. There was a sudden and very violent reaction, and a large quantity of acid was thrown in the face and over the body of Acherman, causing serious injury. L. B. Golden, chief of the Chemical Corrosion Section, was exposed to nitric acid fumes during the ensuing rescue and first-aid operations and died on January 25, 1954. According to the medical report, the direct cause of Mr. Golden's death was pulmonary edema and confluent bronchopneumonia; the contributary cause, was inhalation of fumes from red fuming nitric acid. The following employees of the College Park Station contributed to this report by supplying information on the accident and assisted in the rescue operation: L. B. Golden, chief, Chemical Corrosion Section; T. E. Green, chemist; Robert Warf field, chemist; L. A. DeVivo, laboratory mechanic; D. W. Chalkley, laboratory mechanic; E. H. Neagle, laboratory welder; and R. L. Heath, laboratory general mechanic.

Jan 1, 1955

By J. Douglas Causey

In 1984, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied the 13,730-acre Burnt Lodge (MT-065-278) Wilderness Study Area (WSA) in order to evaluate the mineral resources. The WSA is located in Phillips and Valley Counties, MT, about 55 miles south of Malta adjoining the Charles M. Russell National Wildlife Refuge. It is underlain by near horizontal sedimentary beds of the Hell Creek Formation, Fox Hills Sandstone, and Bearpaw Shale. No mines or prospects were found in the WSA. Bentonitic beds were examined, but are generally less than 1 ft thick and, except where exposed, are deeply buried. Kaolin-bearing sandstone in the Colgate Member of the Foxhills Sandstone was sampled and may have potential for use in structural clay products. However, remoteness and inaccessibility of the area make it unlikely that the material could be economically extracted even though some of the material is marginally useful.

Jan 1, 1985

By A. Broussaud

An original methodology has been developed for steady state simulation of selective grinding and mineral liberation in rod and ball mills. Three fundamental aspects of the methodology are presented successively : modeling ore texture, modeling grinding and its selectivity, and modeling mineral liberation. The methodology for modeling ore texture includes the conversion of 2D data into 3D reconstructed information and the use of the BILCO coherent material balance software. The models for grinding Simulation are classified into three levels, corresponding to three levels of available experimental data. All models account for grinding selectivity and for variations of engineering para-meters and operating conditions. An algorithm has been introduced to forecast mineral liberation, compatible with accurate simulation of selective grinding, which generates reasonable results.

Jan 1, 1987

By G. R. Fitterer, M. B. Royer

The application of manganese in iron and steel metallurgy is very inter¬ esting historically. In general, ancient- irons and steels contained virtu¬ ally no manganese, probably because the available iron ores contained■only small amounts of the manganese oxides. Occasionally, samples of ancient irons were found to have appreciable amounts of manganese, but their presence is considered accidental and dependent upon the ore available to craftsmen of that time. Two specimens of iron (139;— made in 500 A.D. contained .negligible quantities of manganese. A sample of steel which constituted the base of .the Khan Baba pillar in India was probably processed in 12p B. C. by the1 cementa¬ tion of wrought iron. This material; contained 0.02 percent manganese and 0.70 percent carbon (20) . One Damascus-steel sword forged some time between 11'60 ' and l400 A. D. was found to contain 0.1^-i percent manganese and 0.j6l percent carbon. The manganese content of this bla.de was much higher than that of any other material of this type which has been analysed. In every other instance the manganese content was below 0.02 percent. A cast steel manufactured by the East India. Co. in India in the early nineteenth century, under the name of Wootz steel, contained rather appreciable amounts of manganese. This material was made by melting and refining fairly high-manganese pig iron prepared from high-manganese ore. Heath (106), who was working at the Co. plant between 1S20 and 1S40, was convinced that the manganese content of the steel was the determining fa,ctor in its high quality. He learned of certain difficulties English steel manufacturers were having in making even fair-grade steel, and analyses of the material indicated low manganese contents. This convinced him that.if the use of manganese could be introduced in England its steel would be greatly benefited. In consequence, he moved to England and soon was producing certain grades of ferromanganese for use with the crucible process. He recommended addition of this metallic material to the ingot mold just before pouring. It was soon found that inferior brands of steel containing only traces of manganese could be greatly improved by such additions. All metallurgists of that time became convinced

May 1, 1934

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

By Frank E. Chase, Deno M. Pappas, Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By John Ramsay, Frederick A. Edwards, J. Eric Belford, Clarence V. Amyotte

"DEVELOPMENT of the underground mine is carried out from a main ramp driven from surface to the 800 and 1200 levels and from a shaft sunk to 3050 ft. Sub-levels at approximately 100-ft vertical intervals, starting 300 ft above the 800 level, were collared from the ramp as it advanced and a considerable amount of development work was pursued. The lateral and ramp work provided an opportunity to train drift crews, test equipment and methods, assess ground conditions and advance the initial stope development. The development of an exhaust ventilation raise system closely followed the extension of the level development to the south end of the orebody (Fig. 26) . On completion of the shaft, temporary lip pockets were installed at the shaft stations on the 800, 12.00, 1600, 2000 and 2400 levels. The permanent loading pocket had been installed on the 2860 level as part of the shaft-sinking contract and the level had been connected to the 2800-level station by a small muck transfer raise. Development of the 2800-level area was given top priority at this stage. This included a 1000-ft cross-cut to the crusher location, the crusher excavation, storage bins, conveyor ways and a ramp to connect the 2800 level to the loading pocket, the rope changing station and the shaft sump. The development and installation of the rock handling system between the 2400 level and the shaft bottom was contracted to Macisaac Mining and Tunnelling Company, of Sudbury, Ontario."

Jan 1, 1974

By Ike Isagon

Outline 1.Background Sudbury Backfill Operations 2.Alternative Binder 3.Alternative Binder Trial Process Flow Diagram ?Laboratory Results ?Plant Trial ?Final Evaluation and Approval ?Management of Change (MOC) 4.Economics 5.Conclusion 6.References and Acknowledgements

Nov 1, 2011

By James Westfield

Uranium activity has introduced a comparatively new hazard to United States mining. In addition to the hazards common to all mines, uranium mines have a complex health problem of radiation damage. Like many new processes, radiation and nuclear energy can be made to serve man in many useful ways when properly understood and handled; but, like fire, gases, and electricity, their potential dangers must be known and respected, and appropriate precautions must be taken or death may result. Since 1950 the Public Health Service has been conducting basic investigations on exposure to radon and its daughter products and the effect of exposure upon the health of miners in uranium mines of the Western States. The Bureau of Mines assisted in several of these investigations, especially in mines on Indian lands. The studies have shown that a serious health hazard exists from radioactive exposure that might cause lung cancer if continued over a number of years. The Public Health Service report, Control of Radon and Daughters in Uranium Mines and Calculations on Biologic Effects,6/ shows that 55 percent of the uranium mines employing 64 percent of the miners had atmospheric concentrations more than five times the working level now accepted as reasonably safe for industrial exposures. Extensive control measures are necessary to reduce these concentrations to the suggested working level of less than 300 micromicrocuries of total radon daughter products per liter of air.

Jan 1, 1958

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016