Search Documents

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By U Singh

This paper presents the evolution of the studies and strategic plans to extend the life of operations at the Savage River iron ore project in north-western Tasmania. The current Life-of-Mine (LOM) plan for the Savage River operations is based on a series of open pits. Drilling has confirmed high-grade extensions of the magnetite resource at depths that exceed practical limits for open pit mining. Grange Resources Limited, the owner of the operation, is investigating underground options – not only to extend the LOM plan but also to maintain peak production at a reduced operating cost while reducing greenhouse gas emissions into the future. What makes this project unique is that it requires introducing a productive and cost-effective mining method to exploit a challenging geotechnical and geometrical orebody in an area of high rainfall. To support the study efforts, the development of an exploration decline, underground drilling programs, and an exploratory drive excavated into the orebody for geotechnical investigation was key to providing the necessary data for a pre-feasibility study (PFS). This paper describes the pragmatic approach and processes to developing the underground mining options study through data collection and then integrating these options into the open pit plans to optimise an overall strategic plan for the Savage River operations. The learnings for operators from this experience are how the technical and pragmatic approaches were aligned to develop the strategic plans, and the importance of timely investment in gathering the necessary data.

Mar 29, 2023

By AIME AIME

THE Annual Meeting-numerically the 162d meeting-of the American Institute of Mining and Metallurgical Engineers will be held at the Pennsylvania Hotel, 7th Ave. and 33d St., New York, Feb. 18-22, with the exception of the following events: the Mineral Industry Education Division will meet Sunday afternoon and evening at the Columbia University Men's Faculty Club, 400 West 117th St.; and a meeting of the Section Delegates, the annual business meeting of the Institute, and an executive session of the Board of Directors will be held in that order Tuesday afternoon in the Engineering Societies Building, 29 West 39th St., where the Directors will meet in the evening following their annual dinner to the Section Delegates. The Pennsylvania--one of the Statler group of hotels-was selected as headquarters because it has the physical equipment and facilities-for registration, technical sessions of all sizes, luncheons, social events, etc.-as well as the prominence and location desirable for an Institute annual meeting. (A tip for Tuesday afternoon and evening: You can walk underground from the Pennsylvania to within half a block of the Engineering Societies Building,)

Jan 1, 1945

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992

By K. C. Viveros, R. R. Ambriz, C. García, F. De Villèle, A. Talha, D. Jaramillo

Cold hole expansion on base metal, weld metal and heat affected zone of 6061-T6 aluminum alloy welds was simulated by means of finite element method. Three dimensional compact test models with a previous fatigue crack length with a relation of ??= a/W = 0.3, were used to analyze the hole expansion process. Considering the local mechanical properties for each zone of the welded joint, the optimal expansion degree (1.64 to 2.46 %) was determined. The residual stress field, through thickness, after the expansion process in all welding zones, were correlated with the crack opening displacement obtained by finite element analysis. It was observed, that compressive residual stress fields for a post-expansion, in different crack lengths, provided a crack closure mechanism for base metal, weld metal and heat affected zone. Contrary, the crack remained open when residual stresses are positive. The results are given as tangential stresses versus distance from the edge of the cold expansion and crack opening displacement as a function of applied load.

Jan 1, 2014

By Paul E. Lamoureux

Introduction The Author As the pail of smoke and wartime destruction gradually rises from the surface of the earth, from all countries, statesmen assemble to discuss and prepare pacts and treaties which are designed to, once more, bring people of all nations to understand each other and live in harmony. Scientists and engineers throughout the world are also undergoing a drastic reconversion in their ideas and objectives. No longer do they think only in terms of destruction and twist their brains to develop more devastating weapons or to surpass production records of war machinery. They have turned their eyes and ambitions to more pleasant tasks and are taking stock of wartime developments in materials, fabricating procedures, and equipment, many of which had been carefully shrouded with a veil of secrecy, and are applying their new knowledge to the fabrication or improvement of the tools of peace. The next few years will see the gradual elimination of scores of substitutes and makeshifts, expedients which the constantly changing law of supply and demand' under wartime stress necessitated. The universal search for satisfactory substitutes, however, has resulted in a general awakening of plant engineers to the possibilities of materials with which they were relatively inexperienced, with the result that, in many instances, what was considered a substitution at the outset turned out to be more satisfactory than the original material, and, in reality, can be considered a worthwhile development. Not only have materials been explored, but existing fabricating processes have been reviewed, and others, built around the properties and characteristics of new materials, created.

Jan 1, 1947

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By M. H. Kline

The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss, in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve) elongated to the north, approximately 26 miles in length. The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N.C., to the Hcupscup Knob prospects in Carter County, Tenn. The deposits were worked at least us early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.

Jan 1, 1948

The lignite deposits of the United States represent a huge potential source of fuel for power generation. It has been estimated that lignite constitutes about 24 percent of the remaining National reserves of solid fuel on a tonnage basis and about 15 percent of the reserves on a B.t.u. basis. (See sec. 3, part 1.) The major portion of these reserves is in North Dakota. Lignite has been used locally for domestic heating since the first settlers burned it at forts and fur-trading posts as early as 1855. Some of the first studies of the use of lignite in steam boilers were conducted by the Federal Bureau of Mines from 1910 to 1920 (15, 19) 1/ However, the commercial utilization of lignite as fuel for producing power developed slowly. Not until about 1925 was any really successful lignite industrial fuel-blaming equipment developed. Since then the commercial use of lignite as a fuel for producing power has been increasing steadily.

Jan 1, 1954

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By R. L. Dunsmore

Introduction If one had been called upon to describe petroleum oil refining seventy-five years ago, he could have acceded to the request quite satisfactorily in about fifteen minutes. Fifteen years ago, an hour and a half would have been sufficient to give a general idea of oil refining, and of the equipment used for this purpose. Today, so extensive has been the research into all phases of the refining and manufacturing of petroleum products, and so rapid the strides in improvement in technique and equipment, that I doubt if a week would suffice to give an adequate outline of ail the ramifications of present-day oil refining. I propose to only 'hit the high spots', dealing particularly with the equipment and methods employed at the Imperoyal refinery, which you are to visit. Crude oil, the refiner's raw material, contains essentially only two elements, hydrogen and carbon. These are not present in the free state but are combined in various proportions as 'hydrocarbons'. A given crude oil is not made up of just one hydrocarbon, but of myriads; some solid, others liquid, and still others gaseous at atmospheric temperature and pressure, ail dissolved one in the other. Moreover, the nature and the relative amounts of the several hydrocarbons vary very considerably in crude oils from different sources. That is, a 'crude' from Oklahoma will contain hydrocarbons not present in crude from Mexico, and is different again from the Venezuela crude. Not only this but oil in a certain well in, say, Peru may be differently constituted from that in a well half a mile distant from it.

Jan 1, 1931

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

The Morning Star diorite dyke has been subjected to two periods of mineralization. The earlier, genetically related to the dyke magma, gave rise to a weak chalcopyrite-pyrrhotite-pentlandite-gold mineralization in a narrow zone, up to 25 cm. wide, which parallelsthe nearby western (hanging) wall of the dyke. Subsequently a set of conjugate shears formed in the dyke as a result of tectonic movements. Gold-quartz veins formed in these shears giving rise to the classical "ladder veins" of the Morning Star mine. On either side of the veins ("floors") the diorite has been bleached for up to 3 ft. This involved introduction of much CO. and some K"O, and S with abstraction of SiO. and FeO, giving rise to carbonates, sericite, zoisite and pyrite. The veins consist of quartz with minor amounts of albite and carbonate, together with pyrite, arsenopyrite, pyrrhotite, chalcopyrite, sphalerite, tetrahedrite, galena, bournonite, boulangerite and gold. Spectrographic analyses of gold show that the suite of trace elements is consistent throughout the mine.INTRODUCTIONThe gold-quartz veins of the Morning Star Gold Mine, at Wood's Point, Victoria, are a classic example of the "ladder vein" type of deposit. The structure of this series of repeating quartz veins or "floors", some barren and some productive, occurring in a set of conjugate shears which transect a "dyke bulge" of diorite (Fig. 1), has been described on numerous occasions as mining has progressed and figures in the textbooks (Whitelaw, 1905; 1916; Junner, 1920; Lindgren, 1933; McKinstry, 1935; 1942; 1949; Kenny, 1949; Hills, 1952; Clappison, 1953) ; but there has been no study of the mineralization apart from that in Junner's (1920) general study of the Walhalla-Wood's Point Goldfield, made at a time when mining had not developed below the 400 ft. level,. and the mine was dormant.

Jan 1, 1958

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By D Craw, P Whigham, C Rufaut

Geographic Information Systems (GIS) are computerised management systems for spatial data, offering improved data management, extensive data manipulation techniques and greater understanding of data. At the Wangaloa Coal Mine, South-East Otago, ArcGIS is being used to manage, integrate, analyse and visualise the diverse range of datasets being generated from an interdisciplinary research team. GIS will assist with identifying spatial and temporal patterns associated with the current site rehabilitation strategy. This paper will present an overview of how GIS can be a useful tool for understanding ecological recovery during mine site rehabilitation.   The Wangaloa opencast coal mine, owned by Solid Energy NZ Ltd, was closed in 1989 after more than 40 years of operation. Rehabilitation efforts involving more than 60 000 native plants began in October 2001. At Wangaloa sample points were randomly selected at 100 m intervals and recorded using a differential GPS. Plant, soil and invertebrate data have been collected at each sample point. Plots of 8 - 9 plants have been established within approximately 5 m of each sample point. Since September 2003 seasonal monitoring of plant growth and survival has been carried out. Chemical and physical datasets have been generated from soil collected in June and December 2003 for each sample point. A more restricted dataset is being generated for soil collected on a seasonal basis from March 2004. Plant and soil characteristics from these datasets have been attached to each sample point and GIS layers have been created. Relationships between data layers can be explored based on their spatial patterns. Examples presented from Wangaloa include distribution of planting success and temporal variation; temporal change in pH; interpolated pH map; digital elevation model; relationships between planting success and growth with pH and organic matter. GIS is proving to be a valuable tool on the integrated project at Wangaloa.

Jan 1, 2004