Search Documents

By E. E. AGGER, Arthur Notman

THE proposal has been made in a bill introduced into Congress at the last session by Representative Jones of Michigan that an import duty of 6 c. per lb. shall be placed on copper. This action is urged after eighty years of prosperity for the industry in this country; during most of which copper has been on the free list, and during all of which a tariff would have been without real effect. To comprehend the general situation upon which this action would be imposed, we must refer to the past history of the industry and its trends at the present time. The following table supplies us with a picture of the physical growth of the industry in this country and its relation to that of the world as a whole down to Jan. 1, 1921:

Jan 1, 1925

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By S. K. Schwartz

"This paper describes the general layout of the environmental monitoring scheme at Devco 's No. 26 Colliery, including wall face ventilation, fan performance and methane drainage, and then goes on to discuss the sensors, the outstation layout, the surf ace control room and the protection of the system.IntroductionCape Breton coal mines have been pioneers in the use of the latest technology in mining coal on this continent. To mention just one example, continuous methane monitoring at the coal face was started in 1976 and the idea of automatically stopping the face conveyor during high gas levels using the face signalling system was conceived and developed by CBDC engineers.With the introduction of remote environmental monitoring, No. 26 Colliery will be the first underground coal mine in Canada and possibly in North America to have computer-based comprehensive environmental monitoring.Traditionally, surveillance of the mine environment has been based mainly on periodic checks by portable or hand-held monitors. Although this method proved adequate, it has some limitations, namely:1) restricted 'number of observations and samples;2) relatively long time between taking measurements and availability of results for assessment.With remote monitoring, the above limitations are overcome because (a) monitoring is continuous and (b) monitored data are updated quickly (typically 5-7 sec.). Remote monitoring also provides a centralized 'information center' at the surface from where the entire mine environment can be monitored. Details of modes in which data can be displayed and features available at the location will be discussed later in the paper."

Jan 1, 1982

By D Blair, T Scutts, L Fergusson

This paper presents a waste rock treatment and rehabilitation program conducted at a metaliferous mine site in northern New South Wales from 2000–2013. It updates findings from 2005 for Program #1 (which examined acidity, leachable metals and tree growth in a control and three treated areas of waste rock) and includes new results for Program #2 (which examined acidity, plant uptake of metals and trace elements and tree growth in a control and four treated areas compared to undisturbed background levels) and Program?#3 (which examined the treatment and revegetation of submerged mine tailings and an exposed tailings beach).Program #1 showed low soil pH in the control area remained unchanged from years 1–14, and soil pH in the limed and capped areas was initially increased but fell back to starting levels within 12 months and remained low for 14 years. In contrast, soil pH in the Terra B area resulted in soil high pH immediately after treatment and increased in years six and 14 without further treatment. Tree height and density in 2005 and again in 2013 indicated acidity in the control, limed and capped areas suppressed tree height and density; however, in the Terra B area, revegetation in 2013 was comparable to undisturbed forest. Outcomes in the control, biosolids and three Terra B areas in Program #2 were similar to those observed in Program #1.Program #3 showed the submerged and exposed tailings initially had low pH and high concentrations of total and leachable metals before treatment, but these became non-leachable after treatment with Terra B. Revegetation was achieved on the tailings beach, with almost uniform colonisation of bulrush and common reed, along with bottlebrush and golden wattle; a variety of reptiles have also been observed on the revegetated tailings beach, along with migrating ducks, spoonbills and grebes.CITATION:Fergusson, L, Blair, D and Scutts, T, ?2014. Treatment and rehabilitation of acidic waste rock and tailings – a 14-year case study, in Proceedings Life-of-Mine 2014 , pp 247–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

Caterpillar recently held two, two-day demonstration programs for its mining customers. The event, billed as MineDemo by Caterpillar, consisted of two sessions held on consecutive weeks at the company's Tinaja Hills proving ground south of Tucson, AZ. The program included several classroom sessions that focused on Caterpillar equipment applications, including the VIMS (vital information management system) and the CAES (computer-aided earthmoving system). Also included were field demonstrations and the opportunity to test drive mining-related heavy equipment, including dozers, trucks, graders, shovels and loaders. Featured at the event were the recently upgraded 785, 789 and 793 C-Series trucks. Caterpillar recently announced the availability of the 136-t (150-st) 785C and the 177-t (195-st) 789C. The upgraded haulers have replaced the respective B-Series models. The 218-t (240-st) 793C was introduced in 1996. It, too, has been upgraded but retains the C-Series designation. While attending the press event, the author had the opportunity to test drive the 793C at the Tinaja Hills test site. It was amazing how well the machine handled. The operation was smooth and the braking system was precise. The cab was extremely comfortable. To see a C-Series truck in action, the author also visited Newmont Mining's Mesquite Mine, located in Cali¬fornia, across the border from Yuma, AZ. The Mesquite Mine operates a new model 785C truck. At the mine, temperatures have been measured as high as 58° C (138° F) in the pit. Needless to say, the ability to operate dependably in extreme heat is an important consideration for the mine operators. An interview with the driver and later with management confirmed that the 785C has worked out well. The driver praised the comfort of the cab and the ease of operation. Management reported significant fuel savings and was impressed by the truck's maintenance features.

Jan 1, 1999

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By B. C. Jago, H. Derbuch

"The Freightrain kimberlite is located on the Brodeur Peninsula, Baffin Island, Nunavut. Twin Mining is exploring the pipe and adjacent land (79 claims/655 km2) using a combination of airborne geophysics, soil sampling, diamond drilling, trenching and bulk sample processing. The pipe originally was discovered by Cominco Limited in 1975, re-evaluated in 1993 by Lumina Investment Corporation, when it was staked as the Zulu pipe, and subsequently covered by three claims in 1998 by Helix Resources who called it Freightrain.The Freightrain pipe coincides with a strong, ovoid-shaped aeromagnetic anomaly. It is the only surface exposure of kimberlite within a 30 km long linear trend of fourteen aeromagnetic anomalies that are up to 600 m in diameter.The pipe is exposed in the crater facies, near the transition into diatreme facies as indicated by the occurrence of pyroclastic kimberlite characterized by abundant olivine macrocrysts, juvenile lapilli and kimberlite autoliths set in a serpentine-calcite matrix. Olivine, Cr-pyrope garnet and chromite are the most abundant macrocrysts; clinopyroxene, ilmenite and phlogopite mica occur in minor to trace amounts. Garnet and chromite harzburgite, garnet lherzolite, garnet-spinel lherzolite and rare eclogite dominate the xenolith population.Garnet and chromite mineral chemistry indicate encouraging diamond prospectivity and that potentially diamondiferous garnet and chromite harzburgite were the principal sources of diamond in the mantle at the time of kimberlite eruption.Single clinopyroxene grains define an ~42 mW/m2 sub-continental geotherm that is rooted in the diamond stability field. This compares to a slightly hotter geotherm (~48 mW/m2) for adjacent Somerset Island kimberlites with an origin in the graphite stability field. This data accords with the general lack of sub-calcic Cr-pyrope garnet, diamond inclusion chromite and diamond in Somerset Island kimberlites."

Jan 1, 2002

By Michel G. Grenier

Compliance with Diesel Particulate Matter (DPM) exposure regulation is currently performed using timeweighted average (TWA) sampling on underground mine workers. These samples are collected in the span of an entire shift and the resulting concentrations are compared to a legislated exposure limit. While this is very useful to determine the exposure level of an individual to DPM, it fails to clearly identify causes of exposure and highlight opportunities that could help reduce the exposure of workers in the course of the work shift. Real-time DPM monitoring measures the worker?s exposure as a function of time and helps identify circumstances where corrective actions can be taken or design changes can be made by the individual or the employer to reduce the overall exposure of the worker and peers. This work focused on obtaining DPM concentrations using a real-time polycyclic aromatic hydrocarbon (PAH) monitor. The aim was to demonstrate that this instrument, while not a direct DPM analyzer, was able to provide a concentration profile that could easily be linearly correlated to standard TWA elemental carbon measurements. In addition, several instances of improvements that could be implemented to reduce the exposure of underground employees were demonstrated.

May 1, 2010

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By S. K. Mitterecker, T. Hofbauer, F. Baerhold

"Acid regeneration is a very important process step in each acid leach circuit. It is required to recover dissolved metals and HCl from spent leaching acid. Andritz Metals presents its recently commissioned spray roast pilot plant. The facility is now available for testing and demonstrating acid recovery or metal oxide production which is a requirement in several flow sheets under development for the mining and specialized oxides industries. Results from pilot test campaigns are reported here. We are currently focusing on a nickel ore leaching process, which requires both a feasible iron control and acid regeneration step. In addition, we disclose the results of a magnesium ore and aluminium recycling test campaign conducted in our pilot plant facility.INTRODUCTION Hydrochloric acid regeneration is widely used in the steel industry to regenerate spent pickle liquors into hydrochloric acid at a typical concentration of 18 wt.%. Andritz Metals (formerly known as Ruthner) has built more than 200 acid regeneration plants worldwide (Andritz Metals brochure). As technology leaders Andritz also has vast experience with specialty metal oxide plants, producing metal oxides such as aluminium oxide (Al2O3), magnesium oxide (MgO), nickel oxide (NiO), cobalt oxide (Co3O4) and mixed oxides from metal chloride solutions (Baerhold F., Lebl A., Starcevic J., 2006), (Jedlicka, H., n.d.), (Ruthner M.J., Krischner H., 1973), (Ruthner Ind. Planungs AG, 1967). Hydrochloric acid leach circuits have been developed and proven in the industry for many years. Examples of industrial applications are: synthetic rutile production (TiO2) (Walpole E.A., Winter J.D., 2002), Quebec Iron and Titanium’s UGS process (Patoine M.-C., De Mori A., Borowiec K., Coscia C., 2002), magnesium and potassium production (Priemer H., 1973) and Goro Nickel (Vahed A., Colton D.F., Duterque J.P., Karner W., Baerhold F., 2004), (Taylor A., 2013). One of the critical process steps in developing a hydrometallurgical process is acid regeneration, as it is an economic requirement to recover both the dissolved metals and acid (commonly HCl) from the spent leaching solution."

Jan 1, 2016

By Renpei Yoda

An investigation was conducted to develop columbium alloys with e1evated-temperature strengths higher than those exhibited by more common commercial columbium alloys, and attention was given to improving the oxidation resistance and ease of fabrication. Additions of carbon, aluminum, and chromium were made to some columbium-base alloys, and their effects on workability, recrystallization, oxidation resistance, and mechanical properties at elevated temperatures were explored. The additions were made to take advantage of (1) solid solution strengthening, and (2) precipitation hardening. Three alloys displayed good high-temperature properties with relatively good oxidation resistance at 1,000° C, and tensile strengths from 26,000 to 32,200 psi at 1,400° C. When the properties of these alloys were compared with those of commercial alloys, B-66 and FS-85 (1),4 the outcome was favor-able for the alloys studied in this investigation.

Jan 1, 1967

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

By Alvin Schallis

The. problem of supplying enough magnesia for the American war effort has become highly important. Before hostilities began, only about two-thirds of our, require vents came from domestic sources; now they must supply almost all the magnesia we need. A further burden is placed upon our own supply by the fact that more and more magnesia is being required, not alone to pace the war tempo of general industrial activity, but also to replace chrome ore in refractories and to make magnesium metal. The domestic magnesite and brucite industry is equipping itself to satisfy much of this greater demand for magnesia, but the remainder must be obtained elsewhere. The principal sources of magnesia are magnesite, brucite, dolomite or high-magnesium limestone, natural brines, sea water, salt-works bitterns, magnesium silicates, and magnesium salts. Although dolomite is tae subject of this paper, it should be considered in perspective with all these highly competitive sources of magnesia.

Jan 1, 1943

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990