Search Documents

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M. Ziegler

The article deals with the use of a digital twin in the assessment and optimization of a conveyor system in the Chilean copper mine. This example shows that a digital twin is initially just a new (albeit powerful) tool with which the system behavior can be examined. The benefits for the customer arise through the system identification and automatic detection of critical deviations from the target state. This knowledge allows mine management to react and coordinate operational and/or maintenance counter measures to insure optimal performance of their conveyor system. The information derived from the BeltGenius digital twin also allows mine management to gain a clear perspective of the overall efficiency of their conveyors, which will be invaluable for future conveyor component selections.

Mar 2, 2022

By Briggs H.

The illustrated device uses the principle that the lamp can burn with a smaller inlet passage if the air is rich in O2 and that the size of the inlet can be made a measure of O2 percentage. The appliance consists of an adjustable cut-off applied to the inlet of a safety lamp of the improved Gray pattern. Precision is assessed from tables of calibration tests in air contaminated with blackdamp of CO2:N2 composiiton 1:5.67 at temperatures of 40-70 degrees F. Results are presented of tests at St. Germain's colliery, of tests in air contaminated with pure CO2 and of air contaminated with both blackdamp and inflammable gas; published ranges in mine-air blackdamp compositions are tabulated as ranging from 90.06% N2 to 43.90% CO2. When firedamp is present at 1.25-2.5%, its content must first be estimated by means of the cap and a fifth of its value then deducted from the lamp reading for O2

Dec 1, 1916

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, Hara, A. S. Kabir, R. Petrov

Manufacturing of thin sheet is difficult in industries. Some approaches, such as small-draft multi-pass rolling, intermediate annealing, isothermal rolling and high-speed rolling were proposed to overcome the deformability. In this study, different rolling speeds from 15 to 1000 m/min were employed to twin rolled cast AZ31B magnesium alloy to different reductions. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2014

By R. L. Benner

The Bureau of Mines investigated the ZnO-Fe2O3-Fe3O4 system at 1,000°, 1,300°, and 1,400° C, with oxygen pressures between 1.0 and lx10-4 atmospheres. The results, divided into the thermodynamic properties as related to the spinel structure, and the thermodynamic properties as related to zinc concentrate roasting, were used to calculate the activities of ZnO, Fe2O4, and Fe3O4 within the spinel solid solution region of the ternary system, and the pseudo-binary activities of ZnFe2O4 and Fe304. The activities of both systems show large positive deviations from Raoult's Law, especially at high Fe3O4 concentrations. The free energies, the enthalpies, and the entropies of mixing for the binary system were calculated from the binary activities, and the entropies of mixing were compared with two statistical models, one representing an ideal solution, and one representing the mixing of a normal with an inverse spinel. The binary entropy of mixing seemed to be better represented by the latter statistical model, indicating that the tetrahedral and octahedral cations of the reactants tend to remain in the product, even at the high temperatures of the study. This comparison also indicated that the cations of the components are the major contributing factors to the thermodynamic properties.

Jan 1, 1966

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By M. A. Raza

Cable shovels are capital-expensive and primary production equipment in many surface mines. The forces acting on the shovel dipper vary as the dipper moves through the muck-pile. The variations in the forces cause stress loading of the components of shovel and dipper resulting in unplanned downtimes, reduced shovel efficiency, and high mining costs. A potential solution to the above problems is the deployment of an intelligent shovel excavation (ISE) technology, with real-time formation identification, recording, and knowledge transmission capabilities. This research advances the ISE technology by developing dynamic model of cable shovel dipper using Newton-Euler techniques. The model includes the dynamic cutting and dynamic weight forces acting on the dipper as it moves through the muck-pile.

Jan 1, 2011

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldwell Counties in western Kentucky. According to the latest available statistics, this district supplied 1/5,960 short tons of fluorspar in 1937, compared with the total domestic production of 181,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds. The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldrell Counties in western Kentucky. According to the latest available statistics, this district supplied 165,960 short tons of fluorspar in 1937, compared with the total domestic production of 151,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By R. S. Dean

[During the past year the Metallurgical Fundamentals Section gave about an equal amount of time to the experimental determination of fundamental thermodynamic constants and to the demonstration of the application of such data to more directly practical metallurgical problems. The first division of the work - the actual experimental measurements of typical thermodynamic constants - was carried out an two problems, termed ?continuing? programs, namely, (1) measurements of Specific Heats at Low Temperatures and (2) Measurements of Heats of Formation and Free Energies. Specific substances chosen for investigation are classified as (n) those that have been the subject of requests for information from the industry and that, upon examination, seem of sufficient practical importance to justify study, and (b) compounds that are difficult to treat metallurgically, or whose specific thermodynamic properties have not yet been determined satisfactorily and for which accurate data might suggest improved or new methods of Metallurgical treatment, or (c) materials recognized as belonging to a social class with exceptional thermodynamic properties and, hence, of scientific as well as technical importance.]

Jan 1, 1938

By W. H. Hough, P. B. Leavenworth

Development during 1942 led to the discovery of 26 new fields in the Texas Gulf Coast, as compared with 27 during 1941. Of these, 19 are classed as oil fields, 4 distillate fields, and 3 gas fields. Production from the new fields amounted to 614,467 bbl. to October 1942. Producing Sections.—Discoveries in I942, compared with the previous two years, classified by producing formations, are shown in the following table: It is interesting to note the increase in Wilcox discoveries due to the extensive geophysical campaign that has been con. ducted since 1940. Drilling.—During the year 688 wells were drilled, of which 574 produced oil or gas and 114 were dry. This represents a considerable decline in activity over the previous year, when 1405 wells were drilled in the area, of which 1081 were producers and 324 failures. Jackson County continued to hold the lead, with 222 wells completed. Production.—-Despite curtailed drilling, production amounted to 118,009,451 bbl. for 1942, indicating a slight increase over the 113,726,893 bbl. produced during 1941. The statistics in Tables I and 2 include condensate and distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties most of the activities referred to. The number of wells drilled includes only field wells; not wildcats. Outstanding Fields of 1942 The Texas Gulf Coast covered in this report has 270 more or less active oil and gas fields, including the new discoveries of 1942. Of these the most outstanding from the standpoint of production are listed in Table 4. Each of these fields produced one million barrels or more during 1942. Some of the fields where new extensions are occasionally referred to as separate fields, such as West Columbia and New West Columbia, or Thompson and South Thompson, are combined to give a more accurate outline. Two interesting facts may be noted from this list of some 26 oil fields: (I) that the Lolita field, Jackson County, is the only discovery since 1938 to produce more than one million barrels annually, although there have been 79 discoveries since Jan. I, 1940; (2) that 20 of these 26 fields produce from the Frio. New Fields ALief, Harris County.—Pure Oil Company's No. I Mike Albanese was drilled to 8637 ft. in Cook Mountain shale. After numerous tests the well was completed on Apr. 20, 1942, in a Yegua sand at 7919 to 7924 ft. for 54 bbl. of 52' gravity oil and 3,335,000 cu. ft. of gas through

Jan 1, 1943

By W. H. Hough, P. B. Leavenworth

Development during 1942 led to the discovery of 26 new fields in the Texas Gulf Coast, as compared with 27 during 1941. Of these, 19 are classed as oil fields, 4 distillate fields, and 3 gas fields. Production from the new fields amounted to 614,467 bbl. to October 1942. Producing Sections.—Discoveries in I942, compared with the previous two years, classified by producing formations, are shown in the following table: It is interesting to note the increase in Wilcox discoveries due to the extensive geophysical campaign that has been con. ducted since 1940. Drilling.—During the year 688 wells were drilled, of which 574 produced oil or gas and 114 were dry. This represents a considerable decline in activity over the previous year, when 1405 wells were drilled in the area, of which 1081 were producers and 324 failures. Jackson County continued to hold the lead, with 222 wells completed. Production.—-Despite curtailed drilling, production amounted to 118,009,451 bbl. for 1942, indicating a slight increase over the 113,726,893 bbl. produced during 1941. The statistics in Tables I and 2 include condensate and distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties most of the activities referred to. The number of wells drilled includes only field wells; not wildcats. Outstanding Fields of 1942 The Texas Gulf Coast covered in this report has 270 more or less active oil and gas fields, including the new discoveries of 1942. Of these the most outstanding from the standpoint of production are listed in Table 4. Each of these fields produced one million barrels or more during 1942. Some of the fields where new extensions are occasionally referred to as separate fields, such as West Columbia and New West Columbia, or Thompson and South Thompson, are combined to give a more accurate outline. Two interesting facts may be noted from this list of some 26 oil fields: (I) that the Lolita field, Jackson County, is the only discovery since 1938 to produce more than one million barrels annually, although there have been 79 discoveries since Jan. I, 1940; (2) that 20 of these 26 fields produce from the Frio. New Fields ALief, Harris County.—Pure Oil Company's No. I Mike Albanese was drilled to 8637 ft. in Cook Mountain shale. After numerous tests the well was completed on Apr. 20, 1942, in a Yegua sand at 7919 to 7924 ft. for 54 bbl. of 52' gravity oil and 3,335,000 cu. ft. of gas through

Jan 1, 1943

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By Fernando Cillóniz

Benchmarking es un proceso de comparación y medición de los procesos de negocio de una organización, con aquellos que lideran el mercado. De forma que se obtiene información para mejorar el desempeño de las empresas. En ese sentido, el presente texto señala la utlidad del Benchmarking en las empresas donde el uso de la Internet y las tecnologías de la información permiten hacer más eficiente las comparaciones e intercambio de experiencias y conocimientos, así como internacionalizar el proceso.

Aug 25, 2002

By D. Earley

High metal prices and new world trade standards and accounting for environmental liability in financial disclosures are creating markets for metals commodities that are produced using ?green technologies?. A promising "green" gold leaching system uses a polysulfide based lixiviant which is non-toxic and non-polluting. Laboratory testing has demonstrated selective gold extraction rates comparable to those of cyanide. The polysulfide lixiviant is a dilute aqueous solution which can be inexpensively produced from readily available chemical reagents and even mining wastes. The reagent system is self-buffering and maintains the optimal chemical environment for leaching. Treatment of residual leach solutions is not necessary because the lixiviant itself is not toxic, and breaks down as the system equilibrates. Simple closed system boiling is used to recover gold from process solutions. The polysulfide lixiviant can then be readily renewed and recycled back into the system, forming a closed loop system that conserves reagents and energy which minimizes operating costs. Economic projections have shown that the system can be used profitably for standard ore types and grades.

Jan 1, 2009

By D. Parks, A. Miller, M. McNinch, R. Jacksha, H. Nickerson

Each year hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s implementation of an IoT-based intelligent machine monitoring system to improve safety during operation and maintenance at a concrete batch plant. INTRODUCTION Of the hundreds of machinery-related accidents occurring every year in the mining industry, incidents involving stationary machinery at surface mines continue to be amongst the most frequent [1]. A National Institute for Occupational Safety and Health (NIOSH) study showed that the majority of fatal accidents involving stationary machinery at surface mines occurred at sand and gravel (38%) and stone (26%) operations. Of these accidents, entanglement in conveyor components were the most common cause of fatal accidents (48%) [2]. The same study stated that one-third of these accidents involved improper lockout/tagout (LOTO) procedures as a contributing factor. The U.S. Mine Safety and Health Administration (MSHA) acknowledged this problem, stating in a recent request for information (RFI) [3]: “Since 2007, there have been 17 fatalities related to working near or around belt conveyors, of which 76 percent were related to miners becoming entangled in belt drives, belt rollers, and discharge points. Factors that contribute to entanglement hazards include inadequate or missing guards, inadequate or an insufficient number of crossovers in strategic locations, and/or inappropriate lock out/tag out procedures. Systems that can sense a miner's presence in hazardous locations; ensure that machine guards are properly secured in place; and/or ensure machines are properly locked out and tagged out during maintenance would reduce fatalities [3].” In response to this problem, NIOSH’s Spokane Mining Research Division (SMRD) is exploring the potential application of Internet of Things (IoT) technologies to provide cost-effective intelligent machine monitoring systems for improved worker safety [4, 5]. SMRD partnered with Central Pre-mix CRH Company (Central Pre-mix) to develop and install a proof-of-concept wireless IoT solution to monitor machinery and conveyors during operation and maintenance. The primary goals of the system were to provide real-time monitoring of access points and facilitate the planning and execution of LOTO procedures

Jan 1, 2019

By T. W. Johnson

The Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has in progress a study or the flow of natural gas through high-pressure transmission lines. A major problem of this study is to compare the deliveries calculated from the gas pipe-line flow formulas commonly used, with the metered deliveries from pipe lines in operation. In order to obtain such comparisons a series of tests has bean made on 25 operating pipe lines in Kansas, Oklahoma, Louisiana, Arkansas, Texas, and California ACKNOWLEDGEMENTS Study of the flow of natural gas through high-pressure transmission lines was made under the general supervision of H. H. Hill, former chief petroleum engineer of the Bureau of. Mines, H. C. Fowler, acting chief petroleum engineer of the Bureau of Mines, N. A. C. Smith, superintendent of the Bureau of Mines Petroleum Experiment Station at Bartlesville, Okla., and T. Brandenthaler, chief of the oil and gas action of the Bartlesville station.

Jan 1, 1929

By David M. Jurich, Randy J. Essex, Alex de Aboitiz

An Automated People Mover (APM) transit system is planned for the growing Phoenix Sky Harbor International Airport. The APM will improve passenger movements between the terminals, and provide a link to parking facilities, a new rental car facility, and the planned metro Light Rail. The underground works will include shallow twin bored tunnels, taxiway crossings, and underground stations constructed beneath critical airport facilities. Challenging soft ground conditions will require extensive underpinning and ground improvements. Design is underway, and construction is scheduled to begin in 2007 with project completion in 2015. The owner’s planned delivery method for the APM Project will be Construction Manager at Risk (CMAR) with a Guaranteed Maximum Price.

Jan 1, 2005

By P. Clifford

FIPR-sponsored research will playa critical role in enhancing the competitiveness of the Florida phosphate industry as ore grade declines and environmental restrictions tighten. FIPR's program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. The development of a reliable on-line analyzer and a modern process control strategy will result in improved processing efficiency. Significant improvement in overall efficiency will also be realized as the industry adopts column flotation technology. Economic acidulation of high-Insol rock will allow the industry to adopt simplified flotation flowsheets thereby reducing operating costs. Various applications of phosphogypsum would save the industry millions of dollars in constructing and closing gypsum stacks.

Jan 1, 1998

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006