Search Documents

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984

By Susan M. White

Increased coal production, wider use of indiscriminate mining techniques, improved cleaning methods, and greater emphasis on clean fuels is increasing the rate at which wastes accumulate Over the next several years, Colorado Plateau underground coal production is predicted to increase. Currently, mine refuse is deposited in canyons or lowland areas near mines. This study presents information on the nature of coal refuse and disposal practices on the Colorado Plateau. Samples were collected and analyzed to provide information to help formulate alternative methods for reclaiming refuse piles. The analyses were based on determining the capability of unmodified refuse to provide a suitable medium for plant growth. Local topsoils which would be used in reclamation were used as standards. Potential environmental hazards were assessed also. A general cost analysis was done for both surface and underground disposal and the advantages and disadvantages of each were assessed. Several problems were identified which, if solved, would increase the effectiveness of state regulatory programs.

Jan 1, 1982

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By D. M. A. Flight, P. M. Green, J. A. Plant, P. R. Simpson

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The British Geological Survey's regional geochemical database is used to identify the patterns associated with the various mineral deposit types and to examine the extent to which their distribution reflects the presence of long-lived metallogenic provinces in the crust. Image analysis provides new insights into the setting of the mineralisation, geochemical constraints on tectonic models of Caledonide evolution and evidence for terrane amalgamation and large-scale processes. There is evidence that much of the mineralisation reflects the presence of long-lived provinces with a distinctive geochemistry reflecting their origins as zones of crustal extension. In the case of the Middle-Upper Dalradiam sedex deposits, the relationship between geochemistry and tectonic setting is direct. In other cases, rocks deposited in extensional zones appear to have acted as reservoirs of ore-forming elements which were further concentrated during later events

Jun 19, 1905

By G. J. Knighton

Introduction The Sullivan concentrator treats the complex lead-zinc-iron ore from the Sullivan mine of the Consolidated Mining and Smelting Company of Canada, Limited, to make a lead and a zinc concentrate for its metallurgical plants at Trail. Three miles separate the mine and mill, which are situated near the town of Kimberley, in the East Kootenay district of British Columbia. The orebody consists typically of banded sulphides, mainly galena, sphalerite, pyrrhotite, and pyrite. Important factors in the concentration of the ore are its exceedingly complex and its high specific gravity. It should be remembered throughout the paper that results and figures are based on Consolidated's experience with the Sullivan ore. The present mill feed rate is 8,500 dry tons of ore per 24 hours, for an operating week of five and a half days. Grinding and classification of the ore are carried out in three stages and, in addition, there is a re-grind section which re-treats the zinc middling. It is the purpose of this paper to discuss the classification in the various stages and to give the results o comparative tests which have been carried out for the purpose of improving operations in the mill. The Primary stage consists of six units, each made up of a ball-mill and classifier (see accompanying flow-sheet). Four units operate in open circuit and two in closed circuit. The secondary stage consists of eight ball-mills operating in closed circuit with twenty-one classifiers. In the Tertiary stage are two ball-mills in closed circuit with eight classifiers. The re-treatment section for re-grinding the zinc middling comprises one ball-mill in closed circuit with two classifiers.

Jan 1, 1947

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991

By C. J. Pritchard

Controlled recirculation of ventilation air in underground metal and nonmetal mines has the potential to improve airflow and the health and safety of miners when implemented properly. Previous research by Robinson, Marks, Cecala and others concluded that the success of a district recirculation system is predicated upon an adequate supply of fresh air and the use of a reliable monitoring system for safe operation. This recent research also showed that contaminant levels will not exceed pre-recirculation levels, and that district recirculation can improve the dilution of face contaminants, especially methane gas. To illustrate the process of implementing controlled recirculation and also to promote and give guidance to mine operators in consideration of this tool to improve mine airflow, Office of Mine Safety and Health Research (OMSHR) researchers acquired baseline airflow and contaminant data from a multi-level room-and-pillar nonmetal mine and used commercial ventilation network software to simulate base case conditions and recirculation of mine air. Mine return air baseline contaminants of dust and diesel particulate matter were at lower levels than intake air, providing the potential for improved face air quality. A ventilation model implementing controlled recirculation was developed and analyzed, showing an increase in air quantity at the face, improved intake air quality, and contaminant exposure levels below those set by statutory requirements. These results, along with conclusions reached by previous researchers, provide the basis for examining the safe and effective implementation of controlled recirculation in metal and nonmetal underground mines using this mine as an example.

The Midvale Slag Site covers 300 acres in Midvale, Salt Lake County, Utah. Midvale (population 10,000) is part of the Salt Lake City metropolitan area (population 936,000). Between 1902 and 1971, United States Smelting, Refining and Mining Co. smelted ores on the site to produce copper, gold, lead, and silver. Figure 1 shows a picture of the historical Midvale smelter operations. [ ] When operations ceased, the site was estimated to contain 2 million tons of slag from these operations. The smelter no longer exists. In 1971, Valley Materials, Inc., acquired the site to process the slag into materials for railroad beds and asphalt highways. During the 1980s, the U.S. Environmental Protection Agency (USEPA) raised concerns regarding environmental impacts associated with the historical site operations. The Midvale Slag Superfund Site was listed on the NPL in 1991. The Site consists of two Operable Units (OUs): OU1 covering the properties north and adjacent to former ore smelting operations; and OU2 covering the smelter site itself. OU1 had historically been affected by wind blown slag dust and stack emissions occurring on OU2 and the Sharon Steel site further to the south. These emissions resulted in elevated levels of arsenic and lead in the native soils. The EPA issued the final Record of Decision (ROD) for the OU1 Site in 1995. The OU1 ROD required the implementation of institutional controls for the undeveloped portions of OU1 in order to restrict future land use to commercial/industrial purposes unless additional remediation was performed. Hence, the land comprising OU1 was originally considered in the ROD to be suitable for commercial or industrial purposes without the need for remedial action. However, development of OU1 for other land uses, including residential or recreational, would require additional assessment and probable remediation. The OU2 parcel was remediated by EPA to allow future land development, and the Sharon Steel site was remediated by EPA and deleted from the NPL. PROPERTY TRANSACTION AND REDEVELOPMENT In February 2006, a private development company, Mercer Bingham Junction, LLC. (MBJ) purchased 130 acres of the OU1 property for the purpose of performing environmental remediation, and developing mixed residential and commercial real estate. Development of the property was conducted in cooperation with USEPA Region 8 (EPA), the Utah Department of Environmental Quality (UDEQ) and Midvale City. The guidelines under which residential development could occur were defined by EPA. The 130 acres was to be developed for open space, residential and commercial use as part the Midvale City Bingham Junction development. Figure 2 shows the general layout of the proposed land uses. [ ] In May 2005, MBJ began pre-acquisition due diligence activities to purchase the 130 acres of OU1 north of 7200 South Street, which now comprises the Bingham Junction Development. This included the completion of Phase I and limited Phase II investigations. The Phase II investigations were performed to evaluate arsenic and lead concentrations in the planned residential areas of the site, and to explore the contents of the historic landfill on the property. The historic landfill area was on the far west side of OU1, adjacent to the Jordan River. Soil samples collected during the Phase II investigation showed that the planned residential parcels did not currently meet the criteria established in the Tech Memo and that additional placement of fill or soil excavation would be required for residential development in this area. An evaluation performed by the previous owner of the property, Littleson, Inc., showed similar results.

Jan 1, 2009

By S. Thorley

In engineering design of operator?s compartments, in underground mining equipment, ergonomics principles are often neglected or not given the full recognition they deserve. This paper defines ergonomics, applies it to machinery in an underground mining environment and describes the ergonomics analysis undertaken during the design phase of an EJC extra-low-profile mining loader. Encompassing the design of the operator?s compartment of this new loader, this paper illustrates the importance of ergonomics principles within the collective design process, ensuring that it is fully integrated into the design approach. An ultimate aim of this study is to ensure that all future designs follow this route to guarantee not only the outcome of a highly efficient, cost-effective and productive machine but that it is also takes the human factor into account, not only in maintenance but also in operation. Maximizing comfort will have the ultimate outcome of actually increasing productivity.

Jan 1, 2006

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Laurent Dorel

Surface quality monitoring is primarily implemented in the last steps of steel manufacturing before shipment to the end user. However, an increasing trend for also addressing this topic in the upstream stages, such as hot rolling plant, is tackled by Primetals Technologies to give steel producers the key to a global optimized yield management, and efficient “lessons learned” processes. After the last developments of SIAS Next Gen platform, including High Resolution and Near Infra-Red, some site results will be exposed on the very specific high constraints lines such as ESP Endless Strip Production and Plate Mills, and highlights the related most interesting aspects for our customers.

Aug 17, 2017

By J. C. Franklin

A 32-channel continuous monitoring system has been developed to monitor radiation working level (WL), fan operation, and air door position. The system consists of a surface receiver unit and an underground transmitter that is connected to the various monitors. A continuous WL monitor used with the system can generate alarms at two different WL readings. One of these levels is variable from 0.00 to 0.99 WL and generates an alarm on the surface receiver. The other level, fixed at 1.0 WL, generates an underground alarm in the vicinity of the monitor. The detectors for fan operation and air door position work on the principle of a completed circuit to the underground transmitter (multiplexer). When the circuit is broken, as is the case when a fan is off or an air door is open, an alarm is generated at the surface receiver. This alarm remains in effect until the circuit is completed, signifying the fan has been turned on or the air door has been closed.

Jan 1, 1982

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By Sam Bang Jr, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine’has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to sot? material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessaryas vertical presplit drilling produced wall failures.

Jan 1, 1998

MRS. SIDNEY J. JENNINGS, President, MRS. ARTHUR S.. DWIGHT, First Vice-President, MRS. KARL EILERS, Second Vice-President, MRS. H. W. HARDINGE, Third Vice-President, MRS. BRADLEY STOUGHTON, Recording Secretary, MRS. AXEL 0. IHLSENG, Corresponding Secretary, MRS. ARTHUR S. DWIGHT, Acting Treasurer. Welfare Committee MRS. C. C. BURGER, Chairman, Sub-Committees Americanization Belgian Relief MRS. LEVI HOLBROOK, Chairman, MRS. HENRY H: KNOX, Chairman, Emergency MRS. HERMAN A. PROSSER, Chairman. Since the annual meeting held in February, 1917, when the Woman's Auxiliary to the A. I. M. E., was formed, the work of organization, which of necessity must be slow, has steadily gone forward. Under the Chairmanship of Mrs. C. C. Burger of the Welfare Committee, three active sub-committees have been formed: that of Americanization; under Mrs. Levi Holbrook, who is eminently fitted for such a position, by her active and valuable work in a number of the fine patriotic societies of our country; the Belgian Relief Committee, under Mrs. Henry H. Knox, which has clone phenomenal work in the three months of its existence, and whose report is later given in detail; and the Emergency Committee under Mrs. Herman A. Prosser, which has a fund already established, and is. in close touch with Major Arthur S. Dwight, ready to act when necessity arises. The officers of the Auxiliary feel more than gratified at the response so far received, and in a later issue will print extracts from letters, if permission can be gotten from the writers, showing the interest and enthusiasm that have beer aroused by the formation of a Woman's Auxiliary. Answers have even come from far Korea "the hermit nation," from Australia, from South America, showing what a bond of sympathy and, helpfulness is in process of growth. It is our sad duty to announce the death of our Treasurer, Mrs. George D. Baryon, who, from the very inception of our plan to organize, was an inspiring and valuable co-worker. Her place will be difficult to fill. Mrs. Arthur S. Dwight is Acting Treasurer at present. The Auxiliary wishes to express its heartiest thanks to Mr. Stoughton, the genial and efficient Secretary of the A. I. M. E., for his cooperation and valuable suggestions in the difficult work of organizing. He has indeed been "a guide, philosopher and friend." SUSANNE M. IHLSENG (MRS. AXEL 0.), Corresponding Secretary.

Jan 7, 1917

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011