Search Documents

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By H. Richard Eisenbeis, Donna M. Watkins

Many technical professionals (tp)* desire to occupy upper level management positions. But career paths for most scientists and engineers do not extend beyond their specific disciplines. This is unfortunate. Our technical frontiers are expanding so rapdily that it is difficult, if not impossible, to make sound top management decisions without understanding the technical complexities involved. Technical professionals often are not considered for upper level management positions because they lack the managerial and interpersonal skills necessary to become successful administrators. You've heard this before, but a key component of these skills is the ability to communicate. Technical professionals are often unable to communicate as well as they should with nontechnical professionals and nonprofessionals within the organizations that employ them. Communication is important for managerial success Communication is the network of interactions whereby knowledge and understanding are conveyed from one social set to another (Flippo and Munsinger, 1982). In order to be successful, managers must not only be "good" communicators, they must be "effective" communicators as well. Good communication occurs when managers are able to formulate and transmit their messages in such a way that they are received and understood. Effective communication goes one step further: It occurs when recipients accept messages as legitimate and respond to these messages in the manner desired. Before promotion into upper level positions, managers must have developed organizational skills (planning, decision making, organizing, and controlling) and interpersonal skills (directing, influencing, and motivating). Applying these skills effectively is difficult without a highly refined ability to communicate. Effective communication, then, is basic to managerial success. Nowhere, perhaps, has the importance of being able to communicate effectively been emphasized more than in Mintzberg's landmark study of managerial roles (Mintzberg, 1973). Mintzberg's results indicate that executives typically averaged 36 written and 16 verbal contacts a day. These contacts were both important and trivial. They generally occurred in a random manner. Time spent on each varied. Scheduled meetings averaged over an hour. Desk work, telephone calls, and unscheduled meetings required an average of 15 minutes or less. Why technical professionals have difficulty communicating Three reasons why technical professionals do not communicate well are: • The work motivational patterns and personal attitudes of technical professionals are not conducive to effective communication. • Students in technical professions are not encouraged by educational institutions to develop their communication skills. • Organizations do not insist that all technical professionals be able to communicate in the language of business. The work motivational patterns of most technical professionals are indicative of internals and high achievers (Hunt, Salisbury, and Whittington, 1968). As internals, they believe they control their own destinies. As high achievers, they believe that task accomplishment is a primary indicator of success. To ensure a task is completed in the manner desired, tp's attempt to structure and define work situations so they alone are responsible for results. TPs consider the task accomplished when they, and perhaps other tp's, are satisfied with the results. From the tp's perspective, the task may have been completed. From a communication standpoint, two other factors may apply. First, solving the problem required very little interaction (and thus, communication) with others. Second, the tp's, considering the task accomplished, have little concern for how their "technical" answers will be translated to nontechnical persons needing

Jan 8, 1987

By D. A. Buckingham

The Bureau of Mines evaluated potential availability of domestic nickel from 23 deposits, Evaluations included an estimation of in situ and recoverable resources, applicable mining and processing technologies, and capital and operating costs. Discounted cash flow analysis with a 15-pct rate of return was used to determine the average total cost of production of each operation, Identified in situ resources contain 9.0 million metric tons (t) of nickel; 5.5 million t is recoverable as nickel metal or ferronickel. Demonstrated in situ resources contain 8.2 million t of nickel; 4.8 million t is recoverable as nickel metal or ferronickel. No nickel is available at a total cost of production equal to the January 1983 market price of $3.24 per pound. Analyses indicate that potential annual production can only meet current consumption levels at a total cost of production of $7.60 per pound of nickel, Nickel's availability is contingent on (1) successful adaptability of nickel processing methods to domestic resources, (2) location of a smelting facility, and (3) marketability of byproducts and coproducts. Analyses were performed on the effects of byproduct and coproduct revenues, energy, labor, and transportation costs, and metallurgical recoveries on nickel's availability.

Jan 1, 1984

By Tim Martin, Dave Tahija

"In April, 2014, Hecla's Greens Creek mill, near Juneau, Alaska, switched from sulphuric acid to the use of dissolved carbon dioxide for lead flotation circuit pH control. The Greens Creek mine uses paste backfill, in which mill tailings are mixed with cement and used to fill mined areas. Some backfill inevitably becomes part of mill feed during subsequent mining cycles, resulting in high feed pH levels and increased dissolved calcium in the lead flotation circuit. Sulphuric acid is traditionally used to lower pH in such cases but it produces undesirable side effects, including poorer lead-zinc separation and unstable froth. The amount of sulphuric acid used at Greens Creek was limited due to these effects, resulting in higher than target pHs when feed backfill content was high. Dissolved carbon dioxide can be added without these limitations so pH levels have been under much better control since the switch. Additionally, lead-zinc separation and froth characteristics have significantly improved.IntroductionThe Greens Creek Mine, owned by Hecla Greens Creek Mining is an underground mine located on Admiralty Island near Juneau, Alaska, producing silver, gold, lead and zinc in the form of lead and zinc flotation concentrates and a gravity gold concentrate (McDonald, Morgen & Hancock, 2012). The lead and zinc concentrates are produced in conventional flotation circuits preceded by a graphite removal flotation step.The underground mine utilizes cemented paste backfill, of which a certain amount is inevitably re-mined in later mining cycles and returned to the mill, mixed with fresh ore. The Portland cement used in the paste backfill is highly basic so that, from the point of view of the mill, the net effect is to introduce a good deal of lime to run-of-mine mill feed, producing a very high natural pH. This high pH needs to be lowered to obtain good metallurgical results."

Jan 1, 2016

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By C. Slotta, F. Charlier, P. Blomen

"Within the energy concept of the German government, the operating time of nuclear power plants was initially extended from about 8 to 14 years. It is planned, however, that every power plant will gradually be decommissioned until 2025 and that simultaneously the amount of renewable energies will successively be expanded. According to the political state, nuclear energy is a discontinued model. Looking at the global energy market, though, an obviously opposed development can be observed. At the moment, 443 nuclear power plants are running worldwide and further 62 facilities are being built. These about 500 nuclear power stations have to be supplied with nuclear fuel right now and in the future. The present paper will describe the worldwide use of nuclear energy, the extraction of the nuclear fuel uranium and in detail the available and predicted resources of uranium. The conclusion of the paper is the statement that uranium as nuclear fuel is no scarce resource but sufficiently available."

Jan 1, 2011

Factors of importance in the ntilization of coal fines are mentioned, and the results of flotation tests on coal fines from three important coal seams in New South Wales are presented.INTRODUCTIONEconomic utilization of fine coal is an important problem in the Australian coal industry, particularly as the proportion of fines mined is increasing with progressive mechanization.While the use of uncleaned coal fines may be economic, it may be preferable to beneficiate them, but the most economic process must be selected.For beneficiating coal finer than about 28 mesh, froth flotation can be applied, but mining engineers should avoid practices that may be detrimental to flotation. Such practices include the indiscriminate use of water, particularly that containing a wetting' agent, for dust suppression. In addition, clay stemming in wet conditions may produce slimes which could adsorb on coal surfaces, while the use of oils and greases as well as the application of stone dust and chlorides in roadway consolidation may influence adversely fine coal beneficiation.This paper deals with the application of flotation to samples of fine coal from the Bulli, Greta, and Victoria Tunnel seams. In addition a discussion is given of the mineralogical constitution, size analysis, and degree of liberation of ash constituents of the various samples.COAL SAMPLESRepresentative samples of coal from the Bulli, Greta, and Victoria Tunnel seams were obtained for testing.

Jan 1, 1961

By S. W. Zoldok

"ERRATUMFor paragraph 1, page 1, read the following:The Cle Elum nickeliferous iron deposits occur on an unconformable contact between the serpentine and overlying Swauk sandstone formation and extend about 2 miles along the Cle Elum River in Kittitas County, Wash.The linear extent of the deposits and their proximity to a large source of,electric power and coal supply indicated that a development program was in order to determine the probable grade, extent of the ore bodies, and a suitable metallurgical process for recovering the iron, nickel, and chromium from the ore.The northern portion of the serpentine formation was investigated by the Bureau of Mines from August to December 1943 and from August to October 1944. The investigation consisted of road building, diamond drilling, sampling, and metallurgical tests.The Geological Survey assisted with logging of cores and made geologic and topographic maps."

Feb 1, 1948

By M. Rezaee

Push backs used in the production planning of open pit mines play an integral role in generating annual cash flow. Although several algorithms for push back designs have been proposed, none have studied the optimum number of push backs. In this paper, different algorithms have been implemented for the push back design of a cross section of a copper deposit and the results discussed. Moreover, the optimum number of push backs has been determined using analytical and multiple attribute decision making (MADM) methods based on minimizing the risk associated with grade uncertainty, and minimizing stripping ratio, while maximizing net present value (NPV). According to the findings, the optimum number of push backs has been proposed to be between three and six, as lower quantities of push backs are more likely to achieve the calculated net present value, and have smoother stripping ratios for different pushbacks. This approach was examined in an operating mine and the optimum number of push backs determined to be four.

Jan 1, 2012

By Gilberto Yanarico Apaza

"El presente texto señala las pautas necesarias para realizar una evaluación técnica integral de la influencia del collar de bolas para las operaciones de molienda, afectando al desgaste de los revestimientos de los molinos convencionales. Para la determinación del collar de bolas es necesario realizar los análisis granulométricos con la finalidad de obtener el F80 y el P80 de las muestras obtenidas en la alimentación y producto de los molinos, definir el índice de trabajo (Wi) y consumo de energía. Asimismo, se debe considerar el porcentaje de la velocidad crítica, las dimensiones de los molinos, la densidad de los medios de molienda (bolas), el porcentaje de la carga de bolas, las características geométricas de las bolas para molienda y el diámetro real de bolas, que influye de forma inversamente proporcional en la tasa específica del consumo observada."

Jul 1, 2015

By Harry R. Price, Behrooz Tahmasbi, Charles J. Roarty

The 2,408 meter (7,900-foot) long Middle Rouge Parkway Interceptor Extension varies in size from 1.52-meter (5-foot) to 2.36 meter (7-foot 9-inch) inside diameter. Most of the sewer was constructed in tunnel through fine sands and silts. Piping of these soils through the concrete liner eventually resulted in a loss of soil support, settlement and/or severe distress of the sewer, and the formation of several sinkholes. The repair and restoration was generally performed in the sewer and included cast-in-place concrete, shotcrete, cured in place pipe, soil stabilization, cement grouting, dewatering, and chemical grouting. As a part of the work, temporary pump stations and flow diversions were required to perform the work while minimizing discharges to the adjacent Rouge River.

Jan 1, 2007

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By Jun Yang, Zongshan Zou, Mei Qu, Jianjun Zuo

For technical renovation of the thermal plant, one frame structure workshop of 50,000 m2 (59,800 yd2) construction area and one reinforcement concrete chimney of 150m (492 ft) height shall be demolished by blasting at same time. The engineering environment of which is complicated and the accommodation space is limited. Therefore, the collapse sequence, direction, scope of the dismantled building must be accurately controlled to ensure the safe operation of the adjacent generator unit and transformer station. By taking technical measures of theoretical analysis and numerical simulation etc., as well as research on structures collapse method and detailed delay interval, it puts forward the technology of bidirectional folded collapse of the workshop and it uniquely adopts the initiation system that combined with “half-second delay inside drilling” and “millisecond delay outside drilling”. Additionally, by using of the integrated vibration reduction technology in combination of the blasting ruins, buffer ditch and damping ditch, it has safely accomplished the demolition blasting work in high efficiency. Besides the demolition blasting vibration signal is collected and analyzed. The success of the demolition blasting will become valuable reference to other similar works.

Jan 1, 2016