Search Documents

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By G. M. Rao

It has been a universal observation that rich grades of ores and minerals are getting depleted, simultaneously the demands for civilization are ever increasing coupled with occurrence of poor grades of ores and minerals posing a problem to the processing engineers. At the same time, the cost of mining and milling are increasing, creating a situation where the management has to handle and process low grade ores at an economic level keeping environmental stipulations and control to be safeguarded which has been an additional cost for the management to comply with.

Jan 1, 1994

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By J. Janin, J. F. Bougard

Development of improved transportation networks in major urban centers has led more and more to underground construction, the only reasonable solution for decreasing surface traffic congestion. Excavations required by these projects usually cause decompression of the surrounding soil mass which results in subsidence of several centimeters. While these magnitudes of subsidence have no consequences in undeveloped areas, they are often unacceptable in urban areas where existing buildings, structures and utilities are endangered. Recent tunneling projects for the extension of the Paris Metropolitan Transit System (R.A.T.P.) underground network were carried out with this in view and gave rise to the development of a number of innovative techniques for minimizing ground decompression and subsidence. As shown in Figure 1, the recent R.A.T.P. expansion program includes a new express metro, 46 km long, crossing Paris from East to West, and the extension of many existing metro lines in the suburbs. From the start, R.A.T.P. was faced with many unique technical problems for which there was little precedent experience. The structures to be built have large dimensions, with cross-sections typically ranging from 40 to 300 m2, and exceptionally to 600 m2. The new lines are often very deep because the shallow profile is already congested by the existing metro, interceptors, sewers and a very large number of utilities. As a result, new construction is often below ground water level by as much as 20 m. Moreover, the geology varies widely from hard limestone with compressive strength over 1500 kg/cm2 to inconsistent water bearing sand. Finally, curves in the East-West line must have a minimum radius of 500 m which frequently forces the alignment to pass below existing structures, buildings and monuments.

Jan 1, 1974

By A. MacG. Robertson

A cone penetrometer has been used to assess the level of stress existing in hydraulically placed mine backill. The test apparatus was fabricated at the mine and consisted of a steel cone, connector rods and a hydraulic jack. Testing was carried out from a manway passing through the centre of the stope. The cone was pushed horizontally into the fill, both at right angles and parallel to the orientation of the stope walls, and the resistance to penetration was measured. Corrections were made to allow for friction along the rods. In a cohesionless sand, such as mine fill, the point resistance should be directly related to the in situ stress. The stresses in mine backfill are due to o the self weight of the fill o convergence of the footwall and hangingwall of the stope. Silo theory was used to estimate that component of the in situ stress due to the self weight of the fill. The difference between the stress predicted by silo theory and the stress estimated from the cone resistance was assumed to be due to convergence of the stope walls.

Jan 1, 1986

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By A B. Phillips

This paper details the approach adopted to upgrade the current metallurgical facilities at both the Driefontein and Kloof Gold Mines in the Republic of South Africa. Goldfields Ltd operates eight metallurgical plants within South Africa of which three have recently been upgraded to replace the older technology previously installed, with modern equipment. This upgrade was undertaken with a view to improving extraction efficiencies and to reduce operating costs. The upgrade was undertaken in a phased approach with the first phase focused on the replacement of the filtration/zinc precipitation processes with modern pumpcell carbon-in-pulp technology. Included in this upgrade phase was the installation of an automated hands-free electrowinning cell, which represents the first commercial application of its kind in the industry. The second phase of the upgrade entailed replacement of the multiple comminution stages previously installed with large SAG and SAG/Ball mill combinations. Due to the rapid return on these projects, a fast-track approach was adopted which necessitated the purchase of available good conditioned second-hand mills from both within South Africa as well as in Australia. Goldfields Ltd is a large mining house with gold mining operations in South Africa, Australia and Ghana. A well advanced PGM exploration project is underway in Finland- Arctic Platinum.

Jan 1, 2003

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

The biggest Port of Latin America - the Santos Port in São Paulo, Brazil - has been drilled and blasted by controlled underwater techniques in order to remove around 40,000 m3 (52,318 cubic yard) of rock divided in two outcrop rocks: Teffé and Itapema. Underwater pumped explosive, in combination with small cartridges areas, was successfully used in order to reach a target depth of -15m (-49 ft) and a width of 220m (722 ft) in the navigation channel. It was the first time that a pumped explosive was used in underwater blasting in Brazil and it represents a historic benchmark for projects of this kind in this country. The main challenges faced in this project include the control of the ground vibration, due to the necessity to carry out detonations 40m (131 ft) away from the quay wall - where the passenger terminal and the 80 year-old warehouse were located – and the rush schedule available, in order to finish the underwater drilling and blasting phase before the coming cruise season. Therefore, the perfect combination of an ideal pumped product with an effective pumping system has permitted to carry out the project in a record of less time than 3 months (against to the original expected time of 18 months), with all vibration events under control as result of the special ground vibration program carried out.

Jan 1, 2016

By Tian Sugui

By direct aging treated, creep properties measurement and microstructure observation, the influences of the direct aging treatment on the creep behaviors of Hot Continuous Rolled GH4169 superalloy are investigated. Results show that the creep resistance of Hot Continuous Rolled GH4169 superalloy may be obviously improved by directly aged treatment. Under the applied stress of 700MPa at 660, the creep lifetime of the alloy is enhanced to 126h from 60h. During hot continuous rolling, the deformation features of the alloy are the twinning and the double orientations slipping of the dislocation activated within the twinning regions. After direct aging treated, the alloy displays a smaller grain size, and the finer g² phase is dispersedly precipitated in the matrix of the alloy, which is thought to be a main reason of enhancing creep lifetime of the alloy.

Jan 1, 2010

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

The cleaning of copper containing fayalite slag using a CuFe alloy was studied under an oxygen pressure ranging from 10-7 to 5 X 10-11 atm at 1200º c. The reduction of copper from fayalite slags by Cu-Fe alloys was found to be very effective. For example, at a P 02 of 10-7 atm, the copper content in the slag was reduced from 4.1 to 0.402 wt. percent after 90 min. of reaction time using a Cu- 5.27 wt. percent Fe alloy. The copper reduction rates were found to be independent of P02 in the gas phase when using Cu-Fe alloys which exhibit an iron activity of greater than 0.4. A mechanism for slag c1eaning is proposed based on the concept that the Cu-Fe alloy lowers the oxygen potential of the slag according to Eq.1 1, fol1owed by the reduction of cuprous oxide by wustite as shown in Eq.2. Here X represents element X in the alloy phase while (X) represents the element in the slag phase. The copper and iron transfer behaviour obtained in this study are explained by a ?Stepwise equilibrium model.

Jan 1, 1985

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000

By Timo Kankaanpää

Keywords: Solvent extraction, dispersion, phase separation, CFD The liquid-liquid dispersion phases are separated by gravity in a solvent extraction settler. This separation step is made more effective by picket fences. The picket fence geometry and its physical placement have a significant effect on the separation process, because the purpose of a fence is to smoothen and control organic-aqueous dispersion flow in the first part of the settler and achieve a deep and dense dispersion layer in the front end of the settler resulting in a clean phase separation. In this study, physical phenomena in the solvent extraction process and phase separation in a solvent extraction settler with and without picket fences have been examined using a commercial CFX software package. It can be concluded that the used CFD-approach proved to be a complementary tool for optimizing and designing the solvent extraction settler.

Jan 1, 2005