Search Documents

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017

By Jerin Russell

This paper presents a new instrument for real-time detection of excessively coarse material in the overflow pipes of individual hydrocyclones using a non-invasive acoustic measurement technique. The hydrocyclone is an important device used in mineral processing beneficiation circuits for classification of mineral slurries by particle size. It separates a single input stream into two output streams; an underflow of coarse particles that undergo additional grinding for further size reduction, and an overflow stream of finer particles that typically goes directly into a flotation circuit for recovery of the desired mineral. However the hydrocyclone is a major piece of equipment in the beneficiation process that has no instrumentation for directly measuring its performance. The parameters currently measured – inlet pressure, feed flow rate, feed flow density – are common to the entire hydrocyclone cluster which typically has three to twelve hydrocyclones. Thus no information is available to detect individual hydrocyclones that are operating poorly. The system described in this paper detects the presence of unwanted excessively coarse material in the overflow stream of a hydrocyclone using sensors mounted to the exterior pipe surface. It provides real-time monitoring, trending and alarming of the coarse material level. This enables operators to identify poorly performing hydrocyclones, and enables corrective action to reduce or eliminate the coarse material discharge. Improving the classification efficiency of individual hydrocyclones will improve the overall classification efficiency of a hydrocyclone cluster. This leads to less variation in the particle size distribution and slurry density in the flotation feed, which will in turn improve overall mineral recovery. The reduction of unwanted coarse material in the flotation feed reduces the accumulation of that material in flotation cells. This can lead to equipment damage, and unplanned shutdowns due to events such as blocked dart valves.

Aug 16, 2017

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Ulrich Sommers

The Intelligent Furnace (I-Furnace) by SMS group is a smart furnace process and production optimization model. The combination of various tools leads to an optimized heat treatment and production process. It combines a mathematical/physical model to control the furnace with EMG’s IMPOC system for online strength measurement and a newly developed annealing microstructure model to predict material properties. This paper reports about the revamping of an existing galvanizing line, where a mathematical/physical control model has been implemented in combination with an online quality measurement system. This way, the process improvement of continuous galvanizing lines and the quality management of a range of steels including AHSS will be demonstrated. Furthermore, it gives information about the development of the annealing microstructure model to predict material characteristics. Eventually, the I-Furnace will be presented according to the current development and reference status.

Oct 30, 2017

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Li Shanqing, Xu Jianghua, Li Hongmei, Huang Peijie

Cold rolled high strength steel are playing a very important role in reducing automobile weight for energy saving and environment protection. In recent year, more and more high strength steel were manufacturing in steel company. But there are some problems in the cold rolling process for high strength steel products. Periodic thickness deviation especially in strip head or tail is an important one in these problems. In this paper, the reason of periodic thickness deviation was analysed and a new AGC algorithm called Property FFC for high strength steel in tandem cold rolling was developed. The application of this new algorithm shows that it can reduce the thickness deviation.

Oct 1, 2019

By Mohammad Masoumi

In the present study, API 5L X70 pipeline steel samples were deformed by hot-rolling cooled in air or quenched in water and subsequently tempered at different temperatures. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) technique were used to analyze the texture evolution from the initiate state to rolling and tempering state at mid-thickness and near surface plane of all samples. The results showed that the mid-thickness region is richer in {100}//ND oriented grains known as more susceptible to crack formation and growth through. Hot deformed specimen showed dynamic recrystallization grains while quench tempered sample at 700°C evidenced recovery and grain growth.

Aug 16, 2017

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Marcus Vinicius Laudares Mendonça

SMS calculates and improves tooth and flank profiles individually to realise a homogeneous pressure distribution over the complete load flank. With a tooth profile and flank profile according to AGMA, ISO or DIN standard the contact pressure varies along the load flank. To realize a homogeneous distribution of the contact pressure and to avoid a premature mesh, SMS improves the tooth profile and flank profile in three steps. First SMS is doing a preliminary calculation and design according ISO, DIN or AGMA standard, with safety factors based on more than 125 years of experience. Second SMS calculates and checks the local contact pressure at the load flank under consideration of shaft, gearing and housing deformation, as well as the bearing behaviour. Finally SMS calculates and designs an improved tooth profile and flank profile to receive a homogeneous contact pressure at the load flank. The result is an increase of the torque transmitting capacity of up to 30% of the SMS advanced gears with the same outer dimensions than traditional gears.

Aug 17, 2017

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018

By Antonio Esposito

Saving energy and reducing pollution by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and updated. The most modern design tools should be adopted to maximize the coke production rate also ensuring the best coke quality. In this scenario, Paul Wurth is realizing the new coke making plant of CSPecem, Ceara - Brazil. These batteries are based on Paul Wurth “jumbo oven concept”. This solution incorporates all most modern features and design upgrading, in the aim of an easy and long-lasting operation putting a particular attention to environmental performances: the reduced number of ovens and the low number of pushing per day have the main effect of reducing pollution sources. Finally the paper will highlight Paul Wurth SOPRECO® System, which is foreseen to be installed in CSPecem batteries. SOPRECO®, which is capable of controlling the pressure for each individual oven in a coke oven battery, is thus able to reduce volatile emissions through doors, roofs and stand pipes up to 90%. The coke oven gas (COG) produced during the carbonization process is cleaned in a coke oven gas treatment plant to the level stipulated by applying the Best Available Technology (BAT).

Aug 1, 2018

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Darina Manova

Plasma assisted surface modification methods have been used to nitride stainless steels in order to enhance hardness and therefore the lifetime of industrial components. Nevertheless, the corrosion resistance is not always preserved since it is very sensitive to the process parameters, either in implantation or in thermochemical diffusion techniques. AISI 316L stainless steel was plasma nitrided using three different techniques: Low Energy Ion Implantation (LEII), Plasma Immersion Implantation (PI3) and conventional DC pulsed plasma nitriding (DCPN). For each method several parameters were tested and some of them were selected to achieve the so called S phase of about 3 µm thickness and no nitrides precipitation. The nitrided layer was characterized with OM and SEM. Hardness was assessed on the surface with Vickers indenter and 25 g load. XRD was performed to characterize the S phase and to detect other phases if present and electrochemical corrosion tests were carried out in 3.5% NaCl solution. Although the S phase thickness in the three groups of samples was comparable, hardness was not and neither was the corrosion resistance. The PI3 samples were the hardest with the best performance in corrosion experiments, resulting in a higher breakdown potential and lower currents.

Aug 8, 2018

By Ruediger Holz, Tommaso Settimo, Luciano Vignolo

Optimized CAPEX, OPEX, new products, yield and product quality in new process equipment as well as by upgrading of existing facilities are the key factors for success and profitable operation. For this, innovation in processes and design is crucial. Danieli can support their clients by offering innovative and well-thought-out process equipment and upgrade solutions. In 2018, Danieli has put into operation a complete cold processing complex in Turkey, which includes a new continuous pickling tandem mill featuring latest generation of market oriented technologies. In this line, dedicated to run a broad range of size and grades (IF to AHSS as DP1000), the highly efficient Turboflow® pickling process was selected. This technology already proved its efficiency and ability in former applications handling ultra-thin gauges at speeds even exceeding 400 m/min in the pickling tanks. The 5-stand 6-high OSRT tandem mill features important developments, like actuators to improve significantly strip flatness and a special air knife arrangement on the tandem mill exit side to generate perfect strip surface cleanliness. In galvanizing lines, the zinc pot is the most effective area to reduce costs in operation and consumables and increase the product quality. Danieli has spent significant efforts in developing most advanced technology for the wiping process. A fully integrated system solution has been designed to perform a wiping process with high quality, economy, accuracy and productivity. Center part is the newly developed X-Jet / Compact X-Jet air knife, added by new generation electromagnetic stabilizer as well as robotic systems to reduce human intervention and health risks in this area. This technological package is ideal also for upgrade of existing lines, typically generating a return of investment less than 1 year. On top, Danieli has developed advanced automation systems including L2 and L1 controls to achieve outstanding product performances.

Oct 1, 2019

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019