Search Documents

By E. A. Holbrook

MINING Metallurgy, and Petroleum Engineering department in our colleges are facing a crisis; indeed, conditions that threaten their very existence. Unless the Army, Navy, and War Manpower Commission change their present policy, within two years mineral industries education as now carried on will die, because no ablebodied students will be left in the course. If this is the decision of our responsible governmental agencies we of the mining schools must perhaps accept it as a war measure. It might be well however, for the executive of our mining metallurgical, and oil companies to look ahead a, to where they are to recruit a supply of young technically trained engineers. You can no more operate a mine, a steel plant or an oil company without trained engineers than you can operate a battleship without mechanical and electrical engineers.

Jan 1, 1943

By GERALD A. WARING

ALASKA'S coal consumption is now about 130,000 tons annually. About one-quarter of this amount is used in the southeastern part of the territory and in settlements on the western coast and comes from Seattle and from British Columbia mines. About 60,000 tons is sub-bituminous coal from the Healy River mine in central Alaska, and is used mainly at Fairbanks, sixty miles to the north, for heating and the development of electric energy, for the city and the gold-dredging operations of the Fairbanks Exploration Co. The remaining 40,000 or 50,000 tons is bituminous coal from Matanuska Valley, in the south-central part of the territory. These coal deposits extend intermittently for about forty miles along the valley, which trends eastward from the upper end of Cook Inlet.

Jan 1, 1934

THERE is at least one concrete indication that Soviet Russia's two most important iron ore producing centers are seriously depleted. While keeping in mind Russia's penchant for reverse propaganda, one piece of evidence indicates that Magnitugorsk in the southern Urals and Krivoi Rog in the Ukraine have been mined to a point where lower grade ores are being recovered. An article in Pravda, Soviet newspaper, by I. P. Bardin. a Russian metallurgist, says that ore presently mined must undergo an expensive enriching cycle before it can be used in blast furnaces. Com- pounding Russian metallurgical troubles is the low quality of coking coals. High ash and sulphur content typifies the coal Badin talks about. Coal from the Ukraine, Eastern Siberia, Kazakhstan, and the Far East requires extensive treatment before it can be used, according to the article in Pravda.

Jan 7, 1953

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

By B. S. Butler

PART I SUMMARY CERTAIN relations between the formation of ore deposits and other geological processes are pretty generally accepted, namely: that many ore deposits are closely associated with igneous activity; that ore deposits accompany certain types of intrusive bodies, notably batholiths and stocks, and that they are concentrated near the tops of such bodies; that igneous activity occurs in belts of strong folding and faulting; that folding and faulting are greatest in basins of extensive sedimentation and least in areas of erosion or slight sedimentation; that areas of erosion or slight sedimentation and of heavy sedimentation persist over long periods and exert a major control over structure, igneous activity, and ore deposition; that cycles of erosion, deposition, folding and faulting, igneous activity, and ore deposition, have been repeated through geologic time resulting in rather definite periods in which metal deposits have formed. In short, ore deposition is but one phase of a series of closely related geological events. It is attempted in this chapter to point out the relations of these interreacting geologic processes to the distribution of ore deposits in the western United States. Three great periods of mineralization are recognized; pre-Cambrian, post-Jurassic, and late Cretaceous-Tertiary. In distribution the deposits of the three periods, with certain exceptions, show a concentration about two large positive areas, the Colorado plateau and the Columbia plateau, which suggests a causal relation. The most general age divisions of the rocks of the Cordilleran region of the United States are (1) pre-Cambrian, and (2) Cambrian and later rocks. The pre-Cambrian rocks are exposed mainly through the Rocky Mountain belt from the Canadian boundary southward to Arizona and westward through Arizona to southern California. They have commonly

Jan 1, 1933

By A. G. Guy, T. B. Lindemer

A second intepation of the Fick law has been developed and applied to three-place data generated from the Gosting and Fujita solution of the diffusion equation. This integration provides new mathematical techniques for the analysis of experimental data. Through use of the synthetic data it is shown that for concentration-independent interdifiusion coefficients these techniques permit a more accurate determination of the coefficients than does the usual Boltzmann-Alatano analysis. Another technique, applicable to the most general concentration-dependent diffusion coefficients , can be used to determine whether given sets of coefficients are consistent with the experimental ternary concentration-distance curves. DURING the past 10 years the subject of three-component diffusion has advanced from the stage of a laboratory curiosity to the status of an accepted portion of physical metallurgy.1 In the course of this development the underlying treatment for two-component sys- tems was extended and generalized to accommodate the added component, but fundamentally the analyses currently employed for ternary systems are analogous to those previously developed for binary systems. There are several indications that an improved analysis is needed for the ternary case. First, the two cross coefficients, D312 and D321 are typically an order of magnitude smaller than the direct coefficients and consequently are difficult to determine with adequate precision. Second, instead of a single concentration-penetration curve (as in binary diffusion), there are four such curves in the usual determination of ternary diffusion coefficients. These curves have definite theoretical interrelationships, but actual experimental curves exhibit significant departures from these relationships. Finally, the amount of data needed to adequately describe the diffusion behavior of a ternary system is so large that radically new methods are needed to facilitate the gathering of these data. ICirkaldy2j4 has proposed several possible analyses of ternary diffusion data, including some of the methods in current use. A "second-integration" procedure proposed by him4 differed in important respects from that presented here and was not carried to the point of application. Two other methods have been explored by the authors and will be published separately; these are a numerical analysis technique and a method for the analysis of a single ternary diffusion couple. Still other analyses are being explored by various investigators. At present it seems likely that the final analysis of ternary diffusion that evolves will be a composite

Jan 1, 1968

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By Frank Alfred Fahrenwald

A complete list of the elements as given for 1915 includes 18 that melt above 1,700" C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures*and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,' of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation. , Historical.—The alloys of tungsten and molybdenum have received very little consideration during the past. A review of available literature reveals very little regarding this system, and that which has been recorded seems to be at fault. Mennicke2 writes, "Die bekannteste Verbindung

Jan 1, 1917

By T. F. Witheree

The Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its " bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimensions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz.: Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 71/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3 ; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 224 inches high. Diameter of steam cylinder, 20) inches. } Diameter of blast cylinder, 64 inches. } Stroke 5 feet. The engine is direct-acting horizontal non-condensing. December 26th, 1866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 31/2 feet long x 64 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches; nozzles 21/4 inches diameter. Temperature of blast estimated to be about 500°.

DISCUSSION, G. Derge and D. J. Girardi presiding N. A. Gokcen (Michigan College of Mining and Technology, Houghton, Mich.)—While the authors present very interesting results on the effect of sulphur upon the solubility of oxygen, they have not established convincingly the lines of two-fold saturation (the valleys in Fig. 2) and the ternary eutectic point. Their contention that sample S-7, upon melting at

Jan 1, 1954

Coal - Surface Mining Coal Preparation Coal Utilization Research and Development Health and Safety

Jan 3, 1976

By Charles W. Goodale, William A. Akers

The treatment of silver-ores of too low a grade to justify either smelting or preliminary roasting, and yet not " free" enough to permit of raw amalgamation, has ever been a serious problem. As bearing upon it, the operations of the Combination Mining and Milling Company of Black Pine, Deer Lodge county, Montana, during the past year may not be without interest. It is not claimed that the process to be described is not susceptible of great improvement, nor is any claim of originality made for it; but its use is, as yet, not very general, and it seems to offer a means of profitably working the large class of partially-decomposed argentiferous ores which, by reason

Jan 1, 1890

By O. D. Gonzalez

ThIS communication presents the results of a determination of the permeabilities of hydrogen and deuterium in a iron from 360° to 560°C. Recently Heu-mann and primas' have given values of the diffusivity and solubility in a iron of the two isotopes from which the permeability can be calculated. The work reported in the present communication, however, is a direct measurement of the rate of permeation of the isotopes through an identical iron specimen under the same conditions, so that systematic errors can be minimized in the calculation of the ratio of the permeabilities—the value which is usually of main importance in establishing limits for isotopic differences in diffusive processes. Experimentally the procedure used was the usual one: a steady-state flow of gas produced by a pressure difference across an iron membrane was observed as the pressure rise with time in a previously evacuated, calibrated volume connected to the outlet side of the membrane, while a constant pressure of gas was maintained on the opposite inlet side. The membrane was a cylindrical tube 9.38 cm long, 0.730 cm inside diam, 0.187 cm wall thickness, fabricated of 99.95 pct vacuum-melted National Research Corp. iron (less than 0.003 pct C). One end was sealed by a heliarc-welded iron (99.95 pctj lid of 0.147 cm thickness; the other end of the tube was welded to a 304 stainless-steel tube (0.318 cm ID and 0.318 cm wall) which connects to a vacuum system and to the calibrated volume including a dibutylphthalate manometer. The temperature of the iron membrane was maintained constant to ±0.l°C and was measured with an iron-constantan thermocouple which was calibrated against a standard Pt/Pt-Rh thermocouple: the temperature variation along the length of the membrane did not exceed ±0.5°C. Hydrogen was allowed to pass through the membrane assembly for 72 hr at 615°C before permeability measurements were begun. The system was tested at temperature before and after the experiments by a substitution of helium for hydrogen in the inlet side; under these conditions the pressure rise observed in the outlet side was negligible at all times. The gases used for the permeability measurements were 99.95 pct Matheson prepurified H2 and 99.7 pct D2 (0.3 pct HD) from the Isomet Corp. The gases were dried with liquid N2 before use. In Fig. 1 the logarithms of observed flows, jt, for a pressure difference of 73.4 cm Hg are plotted against T-1 Each point in Fig. 1 represents the slope determined by a least-square evaluation of a plot of the pressure in the outlet side of the membrane against time, including at least two separate sets of observations. Each point in the figure has an uncertainty of ±0.6 pct arising from the experimental uncertainty in the pressure and time measurements. The standard deviation of the observed pressures from the straight lines in all cases is less than the experimental precision of the measurements. The observed flow, jt, includes a small but not negligible flow through the stainless-steel connection.

Jan 1, 1968

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08 ADACHI, JINZOO 11 Shiba Park, Shiba-ku, Tokyo, Japan. '88 ADAMI, C. J., Min. Engr., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12

Jan 1, 1917

By S. C. Hollister

An evaluation of the function of the engineer, so that means whereby education can best serve his needs can be adopted. THERE has been a steady increase in specialized branches of engineering during recent years. Some of these are simply specializations in the function of engineering, such as welding engineering, tool and die engineering, petroleum engineering, and refining engineering. Others are associated more closely with the basic sciences, as for example, geological engineering or engineering physics. Still others tend toward the border line of business, such as administrative engineering or general engineering.

Jan 1, 1950

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,' in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young's modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.'.' An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

Sulfuric Acid and Phosphate Industries at Anaconda Reduction Works. BY E L LARISON (Contribution 70-Preprint 4400 words) In 1915 a 135-ton chamber sulfuric acid plant was built at the Anaconda Reduction Works to supply acid for leaching sand tailing Sulfur dioxide was obtained by roasting copper table concentrate Soon after, the flotation process, using acid as a reagent, together with development of a leaching and electrolytic process for zinc recovery, necessitated building a second acid unit of 50 tons' per day capacity, completed in 1917 Within a few months the zinc process was so improved as to consume no added acid Mean¬while research work was in progress on production of phosphate fertilizers using sulfuric acid and Idaho phosphate rock In 1920 a pilot plant was put into operation which treated 50 tons per day of phosphate rock to produce treble superphosphate containing 45 per cent available P205 In 1922 the original plant and process for leaching of sand tailing were abandoned in favor of a combination leaching and flota¬tion process In 1923 the sand leaching plant was remodeled into a treble super¬phosphate plant designed to treat 160 tons per day of phosphate rock. In 1924 the copper flotation process was put on alkaline circuit and acid, has not since been used as a reagent Practically all the acid produced is now used for making phos¬phate products In 1931 the use of copper concentrate as a source of sulfur dioxide was abandoned and an iron concentrate, floated from the copper concentrator tail¬ing, substituted

Jan 1, 1935

By Baxter C. Madden

Stress corrosion is defined and certain examples are illustrated. A number of test methods, to determine the resistance of materials to stress corrosion, are being developed at Wright Field. The criterion as to the validity of a method is stated. Three types of specimens and the method of stressing each type are described. Five different corrosive conditions are set forth. The results of tests to date, although too few for any general conclusions to be arrived at, are presented. The program for the continuation of the investigation is indicated. A bibliography is included. The development of the method of loading a cantilever-type specimen, so that a nearly constant stress at a large deflection may be realized, is presented as Appendix I.

Jan 1, 1945

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936