Search Documents

By W. C. Hardy, B. W. McArthur

The purpose of this work is to show application of laboratory data in calculating solution gas-drive performance of the Cisco K-I reservoir. Included herein is a diagram showing the graphical relationship between six variables common to all solution gas-drive mechanisms. With an iterative process one may assume existence of any of these six variables at a particular pressure and calculate the production performance likely to occur in a reservoir produced by solution gas drive. Four unique pressure values are described at which the material balance equation alone is sufficient to predict the cumulative volumes of gas produced. Information derived from these pressure points establishes a criterion for determining compatibility of the pressure-volume-temperature (PVT) analysis of the produced crude with the gas production history. Two averaging procedures are used to arrive at a relative permeability-saturation relationship which describes the field-wide performance. INTRODUCTION The Cisco K-1 reservoir is a lenticular-type sand structure lying at approximately 6,300-ft subsurface. It is located in the H. and T. C. Railroad Co. Block 97, SW 1/4 S 392 and NW 1/4 S 385, Scurry County, Tex. Correlation of data from logs indicated that the Cisco K-1 reservoir occupied approximately 3,218 acre-ft of space with a closure of from 15 to 20 ft. Analysis of the production data indicates that the initial formation pressure and temperature were 2,450 psig and 121°F, respectively. The bubble point occurred at 1,715 psig after production of 12,256 STB oil and 11,520 Mcf gas. Only traces of water have been produced since initiation of production. Successive material balance calculations from June, 1952, to June, 1957, showed that no initial gas cap or water influx has contributed to production of oil and that the Cisco K-1 reservoir originally contained approximately 1.44 X 10" STB of oil. THEORY Methods for calculating solution gas-drive perform-

By Richard Kunter

INTRODUCTION Additional work has been done on the CIP circuit at Creede, and a brief description of this work is presented in this paper. DREDGE The original dredge for the Bulldog was built by Al Hack, Inc. of Denver. The dredge cutter head is mounted on a boom made of 6-inch diameter pipe which is raised and lowered by a cable-pulley system. Maximum cutting depth is 8 feet. Slurry from the dredge flows through a floating 6-inch diameter pipe supported on 55-gallon drums which runs from the dredge to the shore and then to a trash screen and pumping system. See Figures 1 and 2. The cutter head, suction pump, winches for dredge movement, and all other operations are controlled from a small operations house located toward the rear of the dredge. All of the basic dredge equipment is mounted on a chassis about 8 ft x 16 ft in size. Additional buoyancy was originally provided by sealed 55-gallon drums supported along the sides of the chassis by a small wooden framework. Additional framework and barrels on the front of the chassis on either side of the cutter boom provided additional stability, particularly when digging in hard material. The dredge was quite stable, but two problems were apparent. For one, it could have been sunk by someone from the shore firing a rifle into all of the barrels. In prime deer-hunting and sportsman country

Jan 1, 1983

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By AIME AIME

THE annual meeting of the A.I.M.E. was fittingly closed with a joint meeting of the Metropolitan sections of the four National societies on Feb. 18, at which this subject was adequately discussed by leading engineers before an audience that completely filled the Engineering Auditorium. The large amount of publicity that has been given the Diesel electric loco- motive, and the often garbled reports of its performance and possibilities that have been circulated, makes it particularly fitting that the facts should be given the profession as determined by those who have aided in developing and operating this latest form of prime- mover in railroad operation. C. A. Stein, general manager of the Central R. R. of New Jersey, opened the meeting with a discussion of the problem of electrification, and the relation of the short haul, switching, and terminal service to heavy electrification. Referring directly to the problem of the Central R. R. of New Jersey, some subtitution for the steam locomotive is necessary within the city limits of New York because of local ordinances against the smoke nuisance. While the improvement in the design of the steam locomotive has been marked-the efiiency today is over fifty times that of the locomotive of 100 years ago-it has now probably reached the point of maximum perfection. If anything, it is open to the criticism of having Coo many appliances to get out of

Jan 1, 1926

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.' exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By Frederic Benard

PRIoR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow- • gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 1/4 miles. Although common in steel practice, the transportation of blister copper in this form had not previoisly been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 1/2 tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1944

By I. B. Cadoff, J. C. Bilello, R. Rosenberg

Diffiusion of magnesium into the surface of LiF crystals to controlled depths and subsequent heat treatments provided a wide range of surface zone harahesses and structure, The bend strength of the LiF crystals was increased by as much as an or-dev of magnitude. Ductility was achieved when dislocation generation occurred in the diffusion zone or when dislocations penetrated to the surface from the intevior. A critical surface hardness of 130 to 140 kg per sq mm was found helozu which generation could take place in the diffusion zone and ahoue which the zone was impenetrable, This hardness was obtainable by several methods, among them the aging of quenched MgF2 -LiF solutions to produce MgF, precipitation. Maximum hardness was ohtained in quenched specimens with no visihle evidence of MgF,. Diffusion-zone formation followed a parabolic rate law and an activation energy of 20.9 kcal per mole was obtained for the process. RECENTLY, the properties of ionic crystals as related to surface condition have been receiving much attention, specifically the transitions between ductile and brittle behavior. Originally Joffe 1 showed that NaCl crystals could be made ductile by immersion in water and related this to the elimination of surface microcracks. Aerts and DeKeyser 2 and Gorur 3' have subsequently shown that ionic crystals are inherently ductile and are embrittled through contact with air. Machlin and Murray4 hypothesized that a layer of NaCIO3 produced by contact of ozone with NaCl induced embrittlement by acting as a barrier to outward dislocation flow. westwood,' Rosenberg and Cadoff,9 and Bilello and cadoff' have reported surface strengthening of LiF crystals by coating with a magnesium compound and then heat treating for adherence. The major effect of the coat was to inhibit dislocation-slip lines from reaching the specimen surface. westwoods showed microcrack formation and fracture to be caused by slip-band interactions at the surface. The material presented in this paper is an extension of the work reported earlier by Bilello, Rosenberg, and cadoff'6,7 and illustrates the wide range of surface properties and bulk behavior obtainable by use of heat-treated magnesium-diffused surface regions in LiF crystals. EXPERIMENTAL PROCEDURE The LiF single crystals were obtained from the Harshaw Chemical Co. Some batch to batch variation was observed; therefore all specimens for a given test series were cleaved from the same crystal. The typical dimension used was 1 by 0.1 by 0.40 in. Surface damage resulting from cleavage was removed by chemically polishing in a 2 pct NH4OH solution. Each group of specimens was given a vacuum anneal at 700°C for 4 hr to provide a base standard for measuring comparative effects of various surface treatments. To produce the reacted surface zone, the annealed specimens were immersed in a boiling suspension of MgF, in doubly distilled HzO, agitated slbwly for 30 sec, removed, and dried at room temperature. Uniform coatings of MgF, were deposited with a thickness of approximately 5 mils. It should be noted that this technique can be modified for use with crystals which are soluble in water by using boiling absolute alcohol as the dissolving medium. This was found effective for the coating of NaCl with MgF2. The diffused surface zone was obtained by annealing the coated samples at elevated temperatures in a vacuum of lob4 mm Hg. Penetration depth was controlled by varying the annealing time from 1/2 to 28 hr. After heat treatment, the samples were tested for bend strength and hardness. Load was applied by four-point bending in a hard-beam testing jig. Four-point rather than three-point bending was used to provide a wide area of constant stress and to minimize the effect of localized inhomogenities in the specimen. The deflection rate was 8 x min-' and the distance between knife edges was 1/4 in. Load-time curves were obtained from a chart recorder coupled to the machine and converted to resolved shear stress on the shear plane vs deflection, as plotted in the figures. The unstressed portions of the sample outside of the two outer knife edges were used for the microhardness studies. Microhardness measurements were made with a Bergsman tester attached to a Reichert metallograph. All hardness impres-

Jan 1, 1964

By L. VOGELSTEIN

OUTSTANDING among the year's events in copper has been the reimposition of an import duty of 4r. per pound in this country which became effective June 21. In consequence of this action by Congress, the Ottawa Empire conference recommended a duty of 2d. per pound equivalent at normal rate of exchange to our 4c. duty, on all copper originating outside of the Empire. Lip to the middle of this year only Russia and Japan had a closed market; the import duty on copper in Russia is 30 per cent ad valoremm and in Japan about 2c. Russia's consumption has always been in excess of production and she has imported from 2(1,000 to 40,000 ton, of copper per annum. Japan, with a production of 6,000 to 7,000 tons per month, has absorbed, in normal times, its production, but during recent: sears has exported varyiug quantities in 1929. 2,200 ton-: in 1930, 2,700 tons, and in 1931. 3,600 ton-. Aside from the-e two countries, the international market has heretofore been free. It and when the British Empire duty become, effective the world's markets will be divided into four unit: 1. Russia and Japan, 2. United States. 3. British Empire. 4. Rest of the world. The world's production at present is rennin it the rate of 930.000 tons per annum. This year's production will be over 1,000,000 tons because the several curtailment did not become effective until the second quarter. consumption will be slightly in excess. Deducting from 30,000 tons Russia's and Japan's production of 121.000 tons, 806,000 tons is left divided a, follows:

Jan 1, 1932

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By H. H. Stoek

The fundamental reasons underlying the choicc of a method of mining a coal seam are safety of operation, cheapness of producing the coal and the character of the product as a saleable article. From the standpoint of safety, open or strip coal mining is always preferable, as many of the dangers inherent to underground work are absent, such as explosions of gas and dust, falls of roof and coal, and also to a great extent those due to haulage and the use of explosives, thus eliminating three of the chief causes of accident from which about 75 per cent. of the underground accidents in coal mines occur. The conditions under which coal is stripped also make the work much safer than ordinary quarry work, as the depth of the pit is usually comparatively small. Prom the standpoint of low mining cost, there is much misapprehension and many of the costs given are misleading in that they do not take into account such items as the destruction of the surface for future use, the full cost of the removal of the overburden, depreciation, amortization, coal depletion, loss of time through floods and from bad weather in winter, etc. Coal is no doubt often put on the cars at less cost by stripping than by underground mining, but by no means always so, as is too generally assumed. In some cases coal must be obtained by stripping or not at all, because the small amount of overburden renders underground mining impossible.

Jan 1, 1918

By W. E. Gaby

INTRODUCTION SINCE the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,1 Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the "Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down.

Jan 9, 1916

By E. P. Polushkin, Henry L. Shuldener

THIS paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. PIPES EXAMINED The pipes were made by different manufacturers and their sizes range from ¾ in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often 100 to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is 100° to 160°F. WATER SUPPLIES The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table I are characterized by relatively low hardness, low alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1944

By T. W. Bossert

MELTING is the initial step in the fabricating of all aluminum and aluminum-alloy products. Its function may be considered as threefold: to improve the metal quality, to adjust the composition, and to change the form to that required for subsequent fabrication. Because the melting operation is generally somewhat removed from the final product fabrication, its importance is frequently overlooked. Melting equipment and melting procedures can reflect materially on fabricating procedures as well as on quality and cost of final product. The selection of equipment and the establishment and control of melting procedures, therefore, should be given careful consideration. It is the purpose of this paper to present the various factors that should be considered in establishing melting procedures and in selecting melting equipment. Certain of these are the result of the inherent characteristics of aluminum and can be treated rather specifically. Others depend on the particular production requirements and hence will have to be considered more generally. This paper is intended to cover only the melting of solids, as differentiated from fines, such as borings, turnings, and sawdust. The melting of fines, in many respects, is a subject that should be treated by itself, and practices for melting fines are by no means as standardized as are those for melting solids. The melting of fines is today the subject of considerable developmental interest; hence practices discussed today may soon be replaced by new or improved ones. CHARACTERISTICS OF THE METAL THAT AFFECT MELTING Aluminum and aluminum alloys possess several inherent characteristics that affect the melting problem. Of the physical properties, density, heat content, thermal conductivity, emissivity, and melting temperatures are important because of their effect on equipment design. A list of such properties for commercially pure aluminum is given in Table r, compared with similar properties for iron and copper. The low density of aluminum as well as of the aluminum alloys is of material advantage in the design of melting equipment, in that such equipment can be considerably lighter than similar equipment for handling the heavier metals. The density, however, particularly of the molten metal, is not greatly different from that of the oxides and other nonmetallic materials that develop or become part of the melt during the melting process. Separation of such nonmetallics is not as rapid a process as with some of the other metals, and consideration of this must be made in establishing melting procedures. Sufficient holding time to permit such materials to separate out and, in some cases, fluxing treatments to aid the separation, are required. Since some of these nonmetallics settle to the bottom of the melt, provision should also be

Jan 1, 1946

By Richard Akerman, Frederick Prime Jr

[THE attention now being paid both in this country and Europe the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this subject, is a quite sufficient excuse for presenting this paper to the American Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

By J. J. Lillie

Sublevel stoping was first developed in the Michigan iron mines many years ago. Since that time this method, and modifications with long hole drilling, have been used in a number of non-ferrous mines and have been described in various papers and articles. With a few exceptions, the operations where sublevel methods have been applied are producers of large daily tonnages from ore bodies of considerable size. In selecting mining methods for small properties or relatively small detached ore bodies, sublevel methods often have been overlooked. The method has been used success- fully in relatively small operations at Copper Canyon, Nevada, and, more recently, in mining small ore bodies at Darwin, Calif. As a result of this experience, we believe that a review of the general procedure, the advantages noted, and the results obtained will be of interest to many operators of relatively small mines.

Jan 1, 1949

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965