Search Documents

By Geo. T. Lynch

PALEOLITHIC MAN, laboriously shaping a stone implement in his cave, discovered that the dust irritated his eyes and nostrils and hindered his labors, whereupon, muttering a few incantations, forerunners of modern profanity, he removed himself and his work outside. There, ignoring the jeers of the hairy ?old-timers,? he turned his back to the wind and resumed operations in comparative comfort. Thus originated the dust problem in the mineral industries, and its solution. Despite long familiarity with the annoyance, danger, and loss occasioned by dust, little progress was made in the engineering solution of its problems until recent years. Some advance can now be reported but too many traces of ancient tradition and practice still remain. Considerable published information is available but only a part of this is of proved accuracy and utility. The greater portion is either misleading, being derived from too few cases to be of general application, or entirely erroneous, originating in guesswork, legend, or individual inspiration, divine or otherwise. The engineer, confronted with a dust problem, has neither the time nor the special training required to extract the values from this mass of low-grade. It is, therefore, desirable that we attempt to correlate the known values and to put them into a form upon which actual progress can be based. This discussion is, then, for the benefit of that engineer, particularly the engineer in the mineral industries and more particularly in ore-dressing plants, and is merely a gathering of facts already known but difficult to segregate.

Jan 1, 1938

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep underground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county provides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest competitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By C. C. Whittier

CIVILIZATION'S PROGRESS, which has multiplied man's comforts, conveniences, a n d happiness, is based upon the extensive employment of natural minerals and sources of energy. Mineral resources are basic factors in modern economic development, machine industry, international trade and world power. A survey of mineral consumption shows that the United States leads the world in the production and consumption of energy materials, of metals, and of the large and diverse array of earth materials that fall in the nonmetallic mineral group. The use of nonrnetallic minerals exceeded both the metals and the fuels in the long period before the industrial age, but it is only in the last two decades that consumption of non- metals has kept pace with and approximated in value the output of metals. Although the data of production in the first half of the last century are meager and fragmentary, the record of the past fifty years-the period of most rapid growth-is available, and reveals an astounding growth.

Jan 1, 1933

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.' A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By C. M. Smith

HOWARD N. EAVENSON, acting for the last time as president of the Institute, presided at the annual business meeting on Tuesday afternoon at 4 o'clock. He spoke briefly of his visits with Local Sections last fall, and read a scholarly address on "Mineral Fuels and Civilization," scheduled for early publication in these columns. Karl Eilers presented the Treasurer's report, showing last year's income to be $134,967.44, compared with expenses of $133.266.51. Comparable figures for 1933 were $121,689.90 and $115,462.60. The Institute's peak income was in 1923 about $208,000. Newell G. Alford read the report of the Membership Committee showing 750 new members elected and placed on the rolls in 1934, compared with 328 in 1933. Losses by resignation last year were 81, compared with 262 in 1933; and 691 were suspended for non-payment of dues, compared with 747 the year before. Total membership, including 579 Student Associates, was 7742 at the end of 1934. Applications for membership have been coming in freely the last few months.

Jan 1, 1935

By R. P. Rothwell

IN January last I published in the Engineering and Mining Journal a table giving, with a considerable degree of accuracy, the production of anthracite coal for the year 1874. At that time it was impossible to give any correct estimate of the production of bituminous coal, for the returns I had been able to secure from such distant and scattered districts were not always forwarded punctually, and the work of -obtaining anything like a true estimate of the coal mined in districts from which I was unable to obtain official returns was both laborious and tedious. As will be seen from the detailed reports furnished herewith, I have succeeded in obtaining tolerably accurate returns of 20,093,704 tons; and upon careful revision by numerous well-informed local authorities, my first estimate of the amount of coal not officially returned to me has grown very considerably; indeed, as I get more information on the subject I find that our bituminous coal production greatly exceeds the amount we have been accustomed to hear it placed at, aggregating as it does, 26,465,704 tons. Mr. Andrew Roy, State Inspector of Mines for Ohio, has reported the production of Ohio at 4,168,445 tons, while his first estimates were but 3,820,000 tons; and similarly, in other cases, the more full the returns direct from the mines the more incorrect do I find all previous reports. I am able now to furnish, not an accurate statement, indeed, but by far the most full and reliable one that has yet been published of our coal production. The amount of labor involved in obtaining this admittedly imperfect report has been simply enormous. In the following tabular statement it will be perceived that Pennsylvania produces nearly one-half of all the bituminous coal mined * Since this paper was read fuller reports from some of the States whose production had been "estimated" have modified the figures given. The most serious error is in California, which produces probably 200,000 tons less than these figures. Oregon and Washington territories also yield smaller amounts than here reported; but these reductions are probably fully compensated by fuller reports from other States that were here underestimated. The correct aggregate amount will not vary much from that here given. Early in 1876 I will be able to give a fuller and more accurate report for the year 1875.

Jan 1, 1875

By Sidney A. Swensrud

About a year ago, I attempted in a general way to trace the origin and development of some of the marketing problems of the petroleum industry, and to describe certain trends which it then seemed possible to foresee. To summarize briefly, it was pointed out that the consumption of gasoline, after increasing for more than a decade at an almost unbelievable rate, was slowing down, but that the two factors which determine the supply of gasoline —-namely, the production of crude oil and the percentage of gasoline derived therefrom—were tending steadily to mount. It was suggested that, while the increase in gasoline outlets began with and probably was justified at the start by the rapidly increasing demand, long after all reasonable requirements as to number of outlets had been met the number continued to increase—if anything, at a still more rapid rate—because by that time the overproduction of crude had begun to exert an impelling urge upon the owners of that crude to seek assured outlets for it in the form of gasoline. As more and more companies became integrated all the way from crude oil to marketing, there took place an ever-increasing competition among them, not only for the existing outlets but for new ones. The wide margin between wholesale cost and retail price, which is characteristic of the early stages of most new industries, persisted in the oil industry longer than in most industries, for various reasons. The existence of that wide margin provided in large measure the means of attracting new outlets, for as the gallonage per outlet declined with the increasing number of outlets, competing companies simply offered the dealers a larger part of the total margin. The very nature of competition suggests that such a process would continue until practically all of the available margin was thus given away, and such was clearly the tendency. It was a system that in turn produced increasing marketing expense per gallon on account of the diluted gallonage per outlet; this increased expense might seem to have provided a justification for continuing wide margins. Economics, like its parent, nature, however, progresses by mutations and so began to throw out new types of marketers, in the form of tank-car service stations, cut-price jobbers, and the like—heretics or

Jan 1, 1932

President Howe : It is not so clear to me that the facts which Dr. Waldo brings forward really argue that the nature of the combination between copper and aluminum differs from that of the combination between copper and zinc or copper and tin. As regards electric conductivity, I suppose that the fact, which he thinks points to a special intimate kind of union between aluminum and copper, is that the line in his Fig. 1 is neither straight nor uniformly curved, but that its curvature varies rapidly, not to say abruptly. But we find just such variation in like curves for the copper-zinc and copper-tin alloys. Thus, a slight addition of zinc or tin to copper causes a change in color wholly out of proportion to the quantity added; and, as we add zinc or tin to copper, the tenacity rises very greatly, only to fall off abruptly with further additions of either of these metals. Dr. Waldo : My curve related only to electrical conductivity. The President : If irregularity in one physical property argues

Jan 1, 1895

By A. E. Bellis

ROBERT J. ANDERSON, Cleveland, Ohio (communication to the Secretary *).-The paper by Messrs. Bellis and Hardy was interesting to me and has led me to make a few remarks concerning some of the points brought out. The question of employing correct hardening temperatures is one that is sadly neglected, particularly in many large plants that forge and treat their machine tools for private use. As is most aptly remarked in this paper, "The custom of using one, high-speed temperature for all tools is very poor practice;" still, such practice is more common than otherwise. An instance came to my attention some time ago, in connection with some work with the standardization of high-speed steels for machine tools, where there were no less than six different brands of alloy steels being used for machine tools such as lathe, shaper, planer, boring mill and cutters of like nature. All of these different steels received identical heat and forging treatment-or at least that was the aim of the tool hardener. That the results were highly unsatisfactory goes without saying. That the hardening department of many plants is conducted on a rule-of-thumb fashion is the reason for a great deal of the trouble and disappointment which seems to be the lot of many tool-steel users. Exceedingly crude execution is the rule rather than the exception, and it is no small wonder that the results are as good as they sometimes happen to be. It would seem that at the present price of alloy steels the subject should receive a closer scrutiny by purchasers than it does. One not familiar with the workings of souse plants that disdain to lend an ear to scientific heat treatment would scarcely give credence to some of the methods employed, not only in the treatment of the steel but also in its selection and purchase. Heating for hardening should be conducted under close pyrometric control only after the correct hardening temperature has been determined.

Jan 3, 1917

By AIME AIME

THREE of the addresses presented at this interesting and important session are printed in full else- where in this issue. The fourth, Mr. Hewett's paper, on "Cycles In Metal Production" has been issued as Technical Publication 183, and an abstract of it was published on page 162 of last month's issue. The general discussion that followed these four important papers is given in full below. S. A. TAYLOR: I would like to ask Mr. Veasey whether the control of oil in pools includes royalties, and, if so, in case of a new pool how are you going to control, or rather how are you going to describe the limits of that pool?

Jan 1, 1929

By B. W. Levinger

THE system Ti-CI- has been studied by several investigators." ' Though titanium and chromium are completely miscible at high temperatures, an intermediate phase of the approximate atomic proportions TiCr, has been identified at various compositions between 60 and 68 wt pct Cr. The structure of this phase was established as the cubic C15 (MgCu2) type with 24 atoms per unit cell and a lattice parameter 6.929 kX.2 During a study of the ternary system, Ti-Mo-Cr,5 the existence of a high temperature modification of the TiCr, phase was discovered. In a series of alloys annealed at 1300°C and containing from 60 to 70 wt pct Cr and 5 pct Mo, a new phase was present which did not correspond to either ß solid solution or TiCr,. By trial, the new phase was identified to be of the hexagonal C14 (MgZn2) structure with 12 atoms per unit cell. Further work showed that the hexagonal structure was. in fact, also present in binary Ti-Cr alloys quenched from high temperatures. To make the identification more certain, the intensities of the various reflections were calculated assuming a composition TiCr2 and C14 structure. Table I lists reflection planes, interplanar distances, calculated intensities, and a comparison of these values with the lines of a binary Ti-Cr alloy (66 pct Cr) annealed for 20 min at 1385°C and water quenched. Since high angle lines were more diffuse, the correspondence between visually observed and calculated intensities was not as good at these angles. Lattice parameters were computed to be a = 4.922 kX, c = 7.945, c/a :- 1.614. The corresponding interatomic distances are: titanium to titanium distance, 3.00:, kx, chromium to chromium distance, 2.43, kX, titanium to chromium distance, 2.88,, kX. These compare to 3.00, 2.45, and 2.87 kX in the cubic phase, respectively.' The atomic positions in the C14 structure are as follows: Titanium 1/3, 2/3, Z; 1/3, 2/3, 1/2: 2/3, 1/3, i; 2/3, 1/3, (1/2-z); Chromium 0, 0, 0: 0, 0, 1/2; 2x, 2, 1/4; 232, x, %; X, 22, 1/4; X, 2x, 3/4; x. x, 1/4; x, x, 3/4; The values of x and z were calculated for the alloy mentioned and found as follows: z — 0.061, x = 0.165. The values assumed in the intensity calculations were those for an ideal close-packed lattice or z = 1/16, x = 1/6. Work in the Ti-Mo-Cr system indicates that y2 the hexagonal modification of TiCr2, is the stable phase above 1300°C, while y1 with the cubic structure is stable below 1000°C. X-ray examination of a number of alloys annealed at intermediate temperatures showed that the hexagonal and cubic phases can coexist. Alloys quenched from 1000°C and annealed at 1100" and 1200°C showed small amounts of y2 at the higher temperature. A considerable amount of y, seemed present, however, in cast alloys annealed at 1100°C. It further appears that there is a small but definite solubility range for both phases in the ternary system. Acknowledgment The results of this paper represent work carried out in conjunction with a project sponsored by Watertown Arsenal, Contract No. DA-11-022-ORD-272. References 'M. K. McQuillan: Journal Inst. Metals (1951) 79, p. 379. 2 P. Duwez and J. L. Taylor: Trans. ASM (1952) 44, p. 495. W. J. Van Thyne,. H.. D. Kessler, and M. Hansen: Trans. ASM (1952) 44, p. 974. 1 F. B. Cuff, N. J. Grant, and C. F. Floe: Trans. AIME (1952) 194, p. 848; Journal of Metals (August 1952). Unpublished Research, Armour Research Foundation. "H. J. Wallbaum: Ztsch. Krist. 103, p. 391.

Jan 1, 1954

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By Henry E. Colton

NeaR the town of Christiansburg, Va., occurs a singular feature in topographical as well as geological structure, which may be said to have an important bearing on a large area to the southwest. The great water-shed ridge, which divides the waters flowing into the St. Lawrence from those flowing into the Atlantic ocean, coming southwestward, forms all of what was the boundary of Maine as agreed upon by the treaty of 1783, and a part of the present boundary, all of the northern New Hampshire boundary, and entering Vermont, continues south of Lake George. Passing irregularly through New York, it enters Pennsylvania, and there bifurcating, sends one prong to the west as a divide between the waters of the lakes and the Ohio, while the other becomes the steady, regular ridge which gave it the name of Alleghany, and thus passes on southwestward through Virginia. At no point has it ever been the geological divide. Its course, commencing in the Archean rocks, has passed through nearly every series of formation, and comes into Virginia in the Carboniferous strata. The geological divide—the line between the fossiliferous and the non-fossiliferous rocks—lies, in Canada, to the west of it, but from New York south into Virginia is far to the east. Reference to Dr. Hitchcock'k map will show this. But at the locality noted these positions are changed; the water-divide becomes the eastern chain, and the geological divide is the western, returning, it may be said, to the positions occupied in the region where they originated. These relations are shown on the large map accompanying the present paper. For several miles, the track of the Norfolk and Western Railroad

Jan 1, 1888

By J. H. Yang, K. E. Gray

Results of single-blow bit-tooth impact tests on saturated rocks under elevated confining pressures and zero pore pressure were reported in a previous publication.1 This paper presents an extension of the earlier work to include a study of crater formation during tooth impact on both gas- and liquid-saturated Berea and Bandera sandstones at elevated confining and pore pressures. The basic data obtained were force-time, displacement-time, velocity-time and force-displacement curves during crater formation. Crater volume was also measured and the mode of crater formation determined. Bit tooth geometry, depth of penetration and velocity of impact were held constant. Results indicate that, with pore fluid present in the rock, failure trends from brittle to ductile as pore pressure is increased at constant confining pressure (pore pressure and borehole pressure were equal) For a given rock type, the mode of crater formation was dependent not only upon the nominal effective stress, but also upon the fluid which saturated the rock pore space. When confining pressure and pore pressure were equal (zero nominal effective stress), bit-tooth impact resulted in brittle failure for nitrogen-saturated Berea, and brittle to transitional failure for nitrogen-saturated Bandera; when saturated with liquid both rocks failed in a ductile manner at zero nominal effective stress. INTRODUCTION Dynamic wedge penetration tests have been conducted by investigators in several fields, but the failure mechanism of rock under dynamic stresses is not understood completely. The complex action of drilling bits, even considering the action of a single tooth, may be considered as a combination of drag bit and rolling cutter action. Thus, as a first step in understanding rock breakage in oil well drilling, single chisel impact and rock planing are of fundamental importance. For example, Gray 2 and Crisp3 studied drag bit cutting action at brittle stress states. Simon4 and Hartman5 studied the reaction of rocks to vertical impact by means of drop tests. The depth of penetration, crater volume and force-vs-time curves during crater formation were observed. The significance of indexing single-bit impacts has been noted.4,6-8 Gamer et al,9 reported impact tests on impermeable Leuders limestone at atmospheric and elevated confining pressures. In all cases the tests were accomplished on dry rock and pore pressure was considered to be zero. The importance of both confining pressure and pore pressure on the failure characteristics of rock was described. 10-12 It was found that the yield strength and ductility of porous rock depend on the state of stress under which the sample is tested. The importance of pore pressure on drilling rate in microbit experiments was noted by Cumingham and Eenink. l3 Robinson 12 also pointed out that in drilling the most important parameter in rock failure is the effective stress, where effective suess is defined as confining pressure pc minus pore pressure pp. The effect of pore pressure and confining pressure on rock strength was also noted by Serdengecti and Boozer 14 in strain rate tests, and by Gardner, Wyllie and Droschackl5 in elastic wave studies. Until recently all reported wedge impact studies under simulated wellbore stress states have been conducted on dry rock. Maurer 16 reported impact tests on samples saturated with deaerated water. Borehole and formation fluid pressures were equal in these tests except when mud was used in the borehole. With mud in the borehole and a high borehole-to-formation fluid pressure differential. Maurer observed "pseudoplastic" crater formation. Podio and Grayl reported impact tests on Berea and Bandera sandstone saturated with pore fluids having wide ranges in viscosities. In Podio and Gray's tests, confining pressure was elevated, but pore pressure and borehole pressure were held fixed at atmospheric pressure. The presence of

By Joseph F. Shirley

A froth flotation plant to recover byproduct molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning byproduct molybdenite plant design can be suggested that would be valid for most processes. The term byproduct molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals. Thickener It is considered essential that the feed to a byproduct molybdenite plant be thickened prior to being treated for molybdenite recovery for the following reasons: 1) Thickening allows the rougher and any preconditioning stages to be operated consistently at the optimum percent solids. 2) Generally, the size of equipment used for pretreatment and the rougher flotation is considerably smaller and less expensive than if the copper flotation concentrates were treated directly. 3) The removal of as much water as practical by thickening removes flotation reagents added in the copper flotation circuit, especially frother which can be quite troublesome in a byproduct molybdenite plant. Although thickening of the molybdenite plant feed has long been recognized as necessary to optimum metallurigcal results, very often this area has been designed poorly. The thickener should be sized so that it can produce a consistent thickened product containing 60 to 65% solids without the use of flocculants. Some plants are only able to thicken to 45 to 50% solids consistently while other plants let the percent solids vary from 45 to 60% over a 24-hr period. While the former is more desirable than the latter, in many cases better metallurgical results could be obtained if the percent solids could be held consistently close to 60%. Probably the simplest and most satisfactory system of handling the thickener underflow is to spigot it into a sump, using a sphincter type valve for the orifice, controlled by a density meter. Another satisfactory approach is to use an ODS type pump to meter the underflow. There are other methods of handling thickener underflow which work satisfactorily as long as the amount of copper concentrates entering the thickener is relatively uniform. However, they often fail to operate satisfactorily when there are large fluctuations in the thickener feed rate due to fluctuations in ore tonnage and/or copper grade. If the percent solids in the plant feed could be held close to 65%. There is the possibility the molybdenite plant tailing would not have to be thickened prior to the copper filter plant. This means that the molybdenite rougher float would have to be conducted at 45 to 50% solids with all the cleaner tailings returned to the rougher for dilution. Admittedly, in some situations this approach would be impossible, but if capital or plant area is limited, it should be considered.

Jan 1, 1981

Secondary minerals are the result of a process of concentration and enrichment and are commonly richer than the primary minerals of the same deposit. Secondary ores that contain abundant sulphides are commonly distinguishable in the field from primary ores; this distinction is more difficult with ores that carry a small quantity only of sulphide minerals, and microscopical examination of the ore in thin section is advisable in all doubtful cases. It is frequently difficult, and in some cases impossible, to determine the primary or secondary character of quartzose gold ores. The safest guide is the presence or absence of gaseous or fluid inclusions in association with the ore minerals; such primary association coupled with a lack of traces of oxidation is indicative of primary origin. Any ore that carries traces of oxidation, such as iron stains, endritic oxides of manganese, kaolin and so forth must be considered to have been acted upon by surface agencies, and secondary enrichment must be suspected. Further examination, however, may indicate that the contained value is primary, and, therefore, persistent in its vertical distribution. The manner of occurrence of secondary minerals is frequently characteristic; secondary minerals, being due to the action of surface waters, are commonly found in cracks through earlier minerals, or as crusts lining vugs or surrounding nucleal masses, or in general, in some distribution later than and not conforming to the arrangement of the primary minerals. Secondary sulphides are often found as soft black pulverulent masses or coatings, although they frequently occur well crystallized or as

Jan 1, 1932

By George A. Komadina

From its modest beginning in 1957 with one mill grinding section handling 3000 tpd Pima has steadily expanded. In July 1966, work was completed that allowed the concentrator to treat in excess of 18,000 tpd. Almost immediately Pima embarked on another expansion program that will increase plant capacity to 30,000 tpd during the summer of 1967. This repeated expansion has corresponded with the development of additional low-grade ore deposits and with the improved operating economics realized by handling larger masses of material. Early in the life of Pima it was known that a mineralized area was present on the flanks of the high-grade orebody which systematic drilling had shown to be a low-grade copper orebody. Many months of engineering studies revealed that this was sufficient to allow Pima to compete with other large scale, low-grade copper operations in the Southwest.

Jan 11, 1967

By T. A. Rickard

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To 'punctuate' is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical, or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. .'The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness; proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; 'on the other hand, paragraphs of. excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

By W. F., Dietrich

THIS paper deals with the- methods of mining the high-grade clays of California. Although the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines, this very fact results in a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over fifteen varieties are mined on a? scale of 50 to 200 tons per day; and more than 50 varieties are mined at a rate of less than 50 tons per day. It is the aim of this paper to delimit, insofar as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin and are not considered here.

Sep 1, 1928