Search Documents

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By Christopher J. Bise

Introduction In August 1977, the federal Surface Mining Control and Reclamation Act was signed into law. It stated that: "The Congress finds and declares that because of the diversity in terrain . . . and other physical conditions in areas subject to mining operations, the primary governmental responsibility for developing. authorizing, issuing, and enforcing regulations for surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environmental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall require the operator to adopt measures consistent with known technology in order to prevent subsidence. causing material damage, to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining." This section raises many questions. Precisely what is the "reasonably foreseeable" future as far as land use is concerned? And what is the "standard method of room and pillar mining"? The first part of the paragraph seems to rule out longwall mining, but isn't longwalling a "predictable" manner of "planned subsidence"? Does the Act take into account variations among mining methods in differing regions or coal seams? With these questions and the need to comply with the Act's provisions in mind, many states may turn to the Pennsylvania Bituminous Mine Subsidence Act of 1966- the only comprehensive subsidence act passed by any state-as a model for their own programs. Thus, it is very important to evaluate Pennsylvania's Act to see whether its basic assumptions can accommodate national application. This paper will note the Subsidence Act's provisions and guidelines, briefly analyze the current state-of-the-art in subsidence damage prevention and control, and list several recommendations for altering the Act's application guidelines for different mining areas.

Jan 1, 1982

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identi-fied with our modern "Age of Steel" is a relatively brief interval com-pared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the fore-runner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By V. H. Gottschalk

THE solubility of gases in metals has been of interest since Graham's time in 1866, but, although the subject was actively studied by iron and steel metallurgists during the eighties, the era of painstaking laboratory investigation begins in 1907 with the publication of Sieverts'1 thesis on the occlusion and diffusion of gases in metals. Since then, Sieverts has worked almost continuously in this field, and his views on the subject are the prevailing ones at the present time.2 Probably the most important result obtained by Sieverts, and frequently verified since by other observers, is the discovery that at a constant temperature the solubility of almost all gases in both the liquid and solid state of most of the metals is proportional to the square root of the pressure (for pressure above 100 mm.). The obvious explanation of this fact is that the gas dissolves as atoms and not as molecules, although it has been pointed out a number of times, first by Donnan and Shawl in connection with their work on the solubility of oxygen in silver at 1075° C., that the formation and solution of a compound of the metal and gas would also be indicated by a variation of the solubility with the square or higher root of the pressure. Sieverts4 himself raised the question whether the usual explanation (i. e., that the gas dissolves as atoms) may not be wrong, when he found that the square root law held also for the solubility of sulfur dioxide in molten copper; in which case dissociation into simpler molecules or atoms does not take place. Stubbs5 subsequently showed that Sieverts and Krumbhaar's "constant" for sulfur

Jan 1, 1932

SAMUEL L. HOYT,* Minneapolis, Minn. -I was privileged to see the apparatus used by Mr. Scott, which is quite unique. It is, as the author says, a modification of the apparatus designed by Dr. Rosenhain, but it is evidently quite an; improvement. The author is to be congratulated on the fact that lie has given us, with his apparatus, a quantitative thermal analysis of these critical points. I notice the author refers to Ac3, Ac2, and Ac1. His designation of the Ac2 point is all right, but naturally in a steel with as much carbon as this, which would mean a hypereutectic steel, the other point might better be considered as an Ac, point with possibly another point above the Ac, point. Another important point brought out is the fact that, in Fig. 3, the lines representing the Ar1, transformation and the Ac,1_3 transformation do not intersect at the zero rate curve,

Jan 5, 1919

By John V. Beall

Let's start at the beginning, Mr. Turner. Where and when were you born? In Lansing, Mich., on July 31, 1880. And what was your education? I went to the University of Michigan, where I got an A.B. degree in 1902; then to the Michigan College of Mines at Houghton, graduating from there in 1904 with a B.S. and an E.M. What was your first job in the mining industry, Mr. Turner, and what were you paid? In the summer of 1902, 1 was a field assistant for the U. S. Geological Survey in southwestern Idaho and southeastern Oregon, working under Israel C. Russell, professor of geology at the University of Michigan, who incidentally, had just returned from an expedition to study the effects of the eruption of Mt. Pelee, on Martinique. I was paid $60 a month and found; in addition to doing geologic and hydrographic work, I cooked many of the meals for a party of four, and wrangled four horses. I slept for four months under the stars, without a tent.

Jan 1, 1949

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By Cyril Smith

A COMPLETE discussion of the literature on the subject of the influence of copper on iron and steel will be published elsewhere.1 The present paper is concerned especially with the precipitation-hardening of copper steels, and brief mention will be made here only of the work of Kin-near,2,3 Nehl4 and Buchholtz and Koster,5 who alone have studied this phase of the subject. Kinnear found that normalized low-carbon steel castings containing about 1.0 per cent copper on drawing at temperatures in the neighbor-hood of 530° C. (1000° F.) increased in tensile strength and yield point, with little decrease in ductility. The maximum effect was obtained with about 0.9 to 1.0 per cent copper, and when the copper exceeded 3 per. cent no improvement occurred on reheating. Kinnear did not study the effect of time of reheating-an all important factor where precipitation is concerned. Nehl,6 who apparently was unaware of Kinnear's work, recognized the change as due to precipitation and studied the interdependence of time and temperature of reheating, the temperature of the initial solution heat treatment, and the speed of cooling necessary to retain the bulk of the copper in supersaturated solu-tion and to give an increase in hardness and tensile strength on reheating. Nehl found that if the final rolling or forging temperatures exceeded 700° C. (1300° F.) it was not necessary even to normalize the steel, but full precipitation occurred on merely reheating the forged or rolled shapes at 500° C. (930° F.).

Jan 1, 1933

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By N. A. Ziegler

CONSIDERABLE work has been and is being done on the changes of physical properties that take place in alloys at elevated temperatures, and much information on this subject is published. Much less is known, as pointed out by Rickett and Wood,1 about reactions between the alloys and atmospheric gases and still less is known about changes within the alloy itself under the influence of heat and given atmosphere. Moreover, most of the work published has been done on the alloys of "heat-resist-ing" type, in which chromium is an essential ingredient, the behavior of all other alloys being quite unknown, except perhaps of decarburization produced at the surface by oxidizing atmospheres. It has been shown' that iron, with total amount of foreign ingredients not exceeding 0.01 per cent, if heated in an oxidizing atmosphere at above 900° C., may be saturated with oxygen to 0.1 per cent. It was suspected that something of a similar nature may take place in iron-silicon alloys (transformer material), the mechanism of such processes being either a direct diffusion of oxygen into the alloy, or oxygen combining with silicon to form Si02 or more complicated (silicate) inclusions. Another possi-bility to be considered was that during annealing in oxidizing atmos-pheres, when scale is being formed, silicon may oxidize preferentially at the surface, thus impoverishing the alloy in silicon. In collaboration with Dr. T. D. Yensen,3 the writer set out to investigate this problem about two years ago in order to settle these questions.

Jan 1, 1934

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

By Robert H. Richards

The extent to which sizing by sieves should be carried, as a preliminary to the separation, by jigging, of minerals of different specific gravities, has been a matter of controversy for many years. The subject has been investigated by several authorities, yet the ground does not seem to have been completely covered, nor are the questions involved entirely settled. For my present purpose I shall refer to but three investigators—Rittinger, Munroe, and Hoppe. In seeking additional light, I have gone over part of the old ground which has been considered satisfactorily settled; and since these preliminary tests have thrown light on some points, they have been included in this paper. In the investigations here described, I have confined myself, for several reasons, wholly to small sizes—grains of 0.1 inch in diameter and less. Rittinger's work was mainly done upon larger sizes, and there is much need among millmen of information concerning the smaller sizes. Moreover, these sizes brought the investigation within the means at my disposal. The laws that have been claimed as the laws of jigging by the several authorities are: 1. The law of equal-settling particles. 2. The lam of interstitial currents. 3. The law of acceleration. 4. The law of suction. The first of these has been considered by investigators, generally, to be the most important of all, and the larger part of the work of jigging is thought to be governed by it. But that it does not cover the whole of jigging is clear to all; and to account for the increased efficiency which we may call the extra jigging-catch, the other three laws have been advanced. The investigation described in this paper was undertaken to determine, as far as possible, to what extent each of the four laws con-

Jan 1, 1895

By J. W. Sandelin, L. S. Birks

The group five metals, vanadium, niobium, and tantalum all show cold-rolled textures of {100)(011) and {112)(0ll) with a preference for the (100) in vanadium and niobium and for the {112) in tantalum. Recrys-tallization texture of (100) and (111) was reported1 for vanadium after annealing (no temperature stated). For tantal~m ,~ annealing below 1200°C strengthened the (112) texture but the (111) texture increased and was predominant as the annealing temperature was raised to 2500°C. Annealing niobium up to 1100°C strengthened the ( 100) texture and developed a weak (111) texture.' In the present work niobium has been annealed up to 2000°C. Nearly 70 pct of the grains showed {111) texture with only a weak (112) component and an insignificant (100) component remaining. In addition, double-crystal rocking curves were used to follow the increase in crystal perfection of the grains with increased annealing time. Material and Treatment. Samples i by 4 in. were sawed from & -in.-thick cold-rolled niobium sheet obtained from Wah Chang. Chemical analysis of the material showed it to be 99.4 pct pure with tantalum as the major impurity. Individual pieces were annealed for 2, 15, 30, and 60 rnin in a vacuum of 10'* Torr using an rf generator. They were etched until the grain boundaries were well-defined, Fig. 1. Average grain size varied from 1 mm for 2 min annealing to 2 mm for 60 rnin annealing. Experimental Results. Preferred Orientation. The orientations of 97 of the 117 grains in the specimens of Fig. 1 were determined by back-reflect ion Laue patterns. A General Electric 10-cm-diam cylindrical camera was used rather than the conventional flat camera in order to record more of the low-index spots. The method proposed by Forest, Barton, and schieltz4 was used to transform the cylindrical film patterns to standard stereographic projections. Table I gives the compilation of data. Even 2 rnin anneal at 2000°C is sufficient to yield a strong (111) preferred orientation, and the percentage of grains with this orientation increases steadily with annealing time at the expense of all other orientations. Crystal Perfection. X-ray topographs were taken of each specimen in both the (111) and (112) orientation using the method described by Birks and Grant.' As the anneal time increases, the grains become larger and the individual reflections become slightly more uniform in intensity, indicating an increase in crystal perfection. For a more quantitative measure of crystal perfection, it was necessary to measure the double-crystal rocking curve. The spectrometer employed was a Gaertner instrument of Compton design. LiF was chosen for the first crystal because the (400) reflection with d spacing of 1.05 AU is a good match to the (222) niobium reflection with d spacing of 0.95 AU. CuKp radiation was used in order to further reduce the d spacing mixmatch correction.' A variable aperture was placed between the LiF and the niobium specimen so that a single grain or even a small portion of a grain could be examined. Fig. 2 shows typical rocking curves for the four annealing times. For the 2-min specimen, a single peak is observed with 10' of arc full-breadth at half maximum. As the annealing time is increased to 15 or 30 min, several sharper peaks of 40 to 80" breadth can be seen within a single grain. After 60 rnin anneal only a single peak of about 30" is observed. Table I1 shows the corrected rocking curve breadths and the dislocation densities, ND. The latter were calculated from the equation7 where W is the corrected rocking curve breadth at half maximum in radians and b is the effective Burger's vector. For (110)(111) slip in niobium, b is 2.86 AU. Discussion. The annealing of cold-rolled niobium at 2000°C causes rapid preferential growth of grains with {ill} orientation. After only 2 rnin annealing time, 35 pct of the grains have the (111) orientation, and after

Jan 1, 1968

Organization Place Date 1919 American Society of Civil Engineers..: Twin Cities, Minn. June 17-20 American Society of Mechanical Engineers Detroit, Mich. June 17-20 American Institute of Chemical Engineers Boston, Mass. June 18-21 American Drop. Forge Association Pittsburgh, Pa June 19-21 American Institute of Electrical Engineers Lake Placid, N. Y. June 24-27 American Society for Testing Materials Atlantic City, N. J. June 24-27 Society for Prom. of Engng. Education Baltimore, Md. June 25-28 American Chemical Society Philadelpia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society.. Minneapolis, Minn. Sept. 22-24 American Iron; Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers, Chicago, Ill. Sept. 22-27

Jan 6, 1919

By Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941, when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948.

Jan 1, 1949

By E. S. Hutchinson

The subject of the influence of coal-dust in mine-explosions has received considerable attention both in England and on the continent of Europe, but until the recent disaster at Pocahontas, Va., it seems not to have been of special interest to engineers in this country. The reason, perhaps, is that most of our bituminous mines are worked by short shafts, slopes and drifts; few have been specially dry; and the explosions that have occurred could readily be traced to fire-damp with 110 complicated circumstances. The object of the present paper is to bring together, for the convenience of members of the Institute, the principal English opinions upon this important subject. Messrs. Lyell and Faraday, in their report to the Home Secretary," in England, on the Haswell Colliery explosion in 1844, seem to have been the first to point out that dust fed the flame originating in a

Jan 1, 1885

By B. H. Bergstrom, J. J. Gilvarry

Previously the authors showed that the Gilvarry equation correctly describes the distribution of fragment size in single fracture, provided the exoclastic particles showing original surface of the specimen are removed from the distribution. In the present work this conclusion has been strengthened in two respects. First, it has been shown that the existence of two peaks in the differential distribution for the endoclastic particles, corresponding to the effect of surface and volume flaws in the interior of the specimen, can be demonstrated from the average of data for a large number of specimens. Second, it has been shown by means of a Coulter counter that data obtained from specimens fractured in gelatin display the behavior at fragment sizes approaching 1 p which is demanded by the limiting form of the Gilvarry equation in this case. In previous work, a rigorous derivation of the proper distribution function for fragment size in single fracture of a brittle solid has been given by Gilvarry,' based on a closely defined physical model and deduced strictly by the laws of probability. Experimental work has been reported by Gilvarry and Berg-str~m,~ confirming the theory in its broad outlines. Subsequently, Gilvarry and Bergstrom extended the theoretical discussion to include comminution and presented experimental data bearing on this point. They have described further experimental results for the case of single fracture recently. The experimental evidence regarding single fracture was rather convincing. However, it was based on only five specimens for which fragment sizes were determined by sieve analyses and three for which measurements in the finer sizes were made on a Coulter counter. The purpose of the present paper is to extend the experimental results as obtained by means of both sieve analyses and the Coulter technique. In the former case, sufficient specimens are included so that the average data should vield ac- curately the detailed behavior of the distribution function for the coarser fragment sizes. In the latter case, measurements for the finer sizes are reported which correspond to single fracture more closely than prior results and fill a lacuna left in the experimental verification. In addition, an extension of the theory given recently bGilvarry for the case of fracture of a two-dimensional solid will be outlined, and experimental results obtained by him will be discussed.6 THREE-DIMENSIONAL CASE Gilvarry' has shown that the Schuhmann size modulus is a measure, in a sense specified later, of the number of activated edge flaws in a specimen undergoing single fracture. Single fracture is defined as that resulting from a single instantaneous application of energy, such as the blow of a hammer whose motion is halted when fracture begins. Plural fracture consists of a short sequence of single fractures, as in a jaw or gyratory crusher; multiple fracture obtains when many applications of energy are made, as in a ball mill. The Griffith flaws associated with fracture of a specimen are flaws occurring within the volume of the body, on the new surfaces created within its interior and on the new edges (intersections of two surfaces) within the body. Fracture proceeds by activation of flaws in the volume of the specimen, in the fracture surfaces throughout its interior, and in the edges produced by intersection of fracture surfaces. If all the flaws and all groups of flaws are distributed at random, independently of other flaws or groups thereof, it has been shown by Gilvarry that the distribution function for fragment size has the form of a Poisson distribution. The fraction y, by weight or volume, passing a sieve of mesh size x is given by where k is an average spacing of activated edge flaws, j2 is an average amount of surface containing one activated surface flaw and i3 is an average volume corresponding to an activated volume flaw. The averages in question are referred to the mean dimension x of a fragment. On the basis of the theoretical

Jan 1, 1962

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland's 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977

By John Furness Park

The mining district is located in the northeasterly part of Nevada, between the Jarbidge River on the west and the East Fork of the Jarbidge on the east. The northern boundary of the district is but a few miles south of the Idaho state line—the gold-bearing area extending from this point south, for 5 or 6 miles. • The Jarbidge Mountains, in which the ore deposits occur, range from 5000 to 11,000 ft. in elevation, the most important mines being situated about 7000 ft. or higher. The town of Jarbidge lies along the Jarbidge River and is reached by stage from Rogerson, Ida., the nearest railroad point. During the summer months, the camp may be entered from the south by way of Deeth, Nev., but no regular transportation facilities are available over this route. History The mineral deposits were not discovered until 1909, when D. A. Bourne, panning along the river bank, found gold in. the gravel at the mouth of a small stream flowing into the Jarbidge. He prospected in the vicinity of this stream, later known as Bourne Gulch, and shortly after located the North Star claims. During the following spring and summer (1910), the camp of Jarbidge grew from nothing to a town of 2000 people and the hills surrounding it were practically all taken up by mining claims. Most of the work done during the first year or two consisted of trenching and open-cut prospecting. Tunneling was started on a number of claims and many veins were uncovered. Mills were built and operated on a few properties, notably the Pavlak and the North Star. These ran only a few months, however, when they were closed down because of extraction and financial difficulties. A period of development followed in which the majority of the present producing mines were opened. The Elkoro Mines Co. acquired a number of claims in 1915 and started work on the present mill in 1917. Since that time other properties have been taken over until this company is by far the largest operator in the district. Only one other company is now actively engaged in mining, the Bluster Mining & Milling Co., which has

Jan 1, 1925