Search Documents

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore ex- ploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composi- tion laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, varia- tions are functions of distance. Hence, in either case, variations along the hole are of greater effect than across it.

Jan 1, 1949

By AIME AIME

Maurer's review summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled.

Jan 1, 1967

By H. D. Wilde

GREAT emphasis is being placed today on petroleum as a source of chemicals. Such prominence is well merited, for rapid strides have been made in developing processes for the conversion of petroleum into synthetic chemical products, which are now being made on a huge scale. These marvelous accomplishments have resulted in some highly optimistic predictions as to what can be expected in the future. Many of these forecasts are well justified, but some writers, especially those contributing to the Sunday supplements and the popular-cience type of publications, have let their imagination run wild and present a rather distorted picture of the possibilities in this field in the postwar period. Commercial manufacture of synthetic organic chemicals had its beginning in England with the establishment of a plant by Sir William Perkin in 1857 for the manufacture of "Aniline Purple" or "Mauve." The preceding year he had discovered in the laboratory how this dyestuff could be made from aniline, one of the many derivatives of coal tar, and he soon made commercial application of his discovery. Influenced largely by his success, organic chemists began research on production of a vast array of synthetic dyestuffs, medicinals, flavors, scents, and explosives. Rapid progress was made and by the turn of the century hundreds of these products were being manufactured. Most of these synthetic chemicals were derived from materials obtained as by-products in the conversion of coal into coke. These by-products are generally referred to as "aromatics" and are obtained by processing coal tar recovered in the coking process, so they are popularly known as "coal-tar chemicals." During the early years of this century, coal-tar chemistry was the wonder of the age, and rightfully so, since the products so made seemed limitless.

Jan 1, 1944

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

By DONALD H. McLAUGHLlN

Few factors have had more influence in maintaining the strength and stability of the United States than our persistent habit of providing .checks and balances to the dynamic powers of free enterprise on the one hand and to the controls and guidance exercised by the State on the other. .Indeed, it is this same concern for matching forces against each other that has given our republic its ability -to preserve a democratic basis of life for its citizens, and yet maintain a ,government that is able to protect the rights of all and to resist and minimize the danger of excessive concentration of authority. Our current efforts to clarify the nation's mineral policies and to define more clearly the role that the governmental agencies should play in conjunction with the functions of private -enterprise again reveal the desirability and advantages of maintaining our traditional controls. At times, the equilibrium has been temporarily disturbed by too great enthusiasm for one or the other of these basic concepts. Sooner or later, however, the balance has been restored by the healthy opposition that is always created by excesses of one sort. At the current stage in our history, the swing toward undue enlargement of the powers of the State seems to have gone dangerously far and we would be untrue 'to our traditional behavior if the group that must demonstrate the virtues of free enterprise did not rally to its support with the utmost earnestness.

Jan 1, 1949

By Andrew Fletcher

AS good health is the most important asset in life, the development of healthful conditions should be the one common meeting ground of agreement between management and labor. Health should not be a subject to be pulled apart, shoved around, or bargained about. Differences of opinion may exist in the procedure and techniques employed in approaching the goal of maintaining the health of workmen, and in the method of increasing the ultimate profit of the employer by improved working and living conditions. Such matters are doubtless appropriate subjects for discussions between the interested parties, but techniques are only tools. If an employer fails to remedy a hazard or a menace which contributes to poor working condlions, this constitutes a legitimate grievance. It should not be necessary, however, nor is it desirable that fundamentals of health maintenance become matters of collective bargaining, any more than should the principles of management and engineering. I have been especially concerned during the last few months with the propaganda in collective bargaining negotiations throughout the country for including in union contracts a given number of days of sick leave with pay. We all

Jan 1, 1946

For the year ending February, 1923 PRESIDENT ARTHUR S. DWIGHT, District 0 NEW YORK, N. Y. PAST PRESIDENTS HERBERT HOOVER, District 4 WASHINGTON, D. C. EDWIN LUDLOW, District 0 NEW YORK, N. Y. FIRST VICE-PRESIDENT J. V. W. REYNDERS NEW YORK, N. Y. TREASURER CHARLES F. RAND NEW YORK, N. Y. SECRETARY FREDERICK F. SHARPLESS,. . . . . NEW YORK, N. Y. ASSISTANT SECRETARY PERCY E. BARBOUR NEW YORK, N. Y.

Jan 7, 1922

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 7, 1917

By Thomas T. Read

REVIEWING the events of the year in mineral industry education, a certain amount of either amusement or irritation, depending upon one's viewpoint, can be derived front the section dealing with mining engineering in Walter B. Pitkin's "New Careers for Youth" which appeared during the summer. On p. 102 Prof. Pitkin says "The mining engineer is disappearing .. . because . . . the profits of mining decline rapidly with the age of the mine." In his "Are Too Many Students Taking Mining Courses?" published in the May issue of this journal, W. B. Plank presents statistics showing that there was some decline in student enrollment in mining and metallurgical courses in 1932-3 and 1933-4, compared with 1930-31, but that the decline was proportionate to that in all lines of engineering study combined. Informal reports from Institute officials that have visited tinning schools during the fall indicate that nearly all schools showed an increase in enrollment for the current school year. Pre else statistics will be made available by Prof. Plank at the Annual Meeting. His study last year provided, for the first time, accurate and complete information on the enrollment in mining schools, as well as the number of various courses and the degree granted, and it will be interesting to have comparable figures for this year. Prof. Pitkin's views on the future opportunities for mining engineers were discussed at some length - on pages 439-4.40 of the November issue of MINING AND METALLURGY.

Jan 1, 1935

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By Saluja, Sunder S.

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including fire setting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century.

Jan 1, 1968

By Ronald C. Whiting

SINCE the advent of what has been aptly called "chemical flotation," about 1920, the number and complexity of the various chemicals used in practice have increased enormously. Over 300 patents have been issued dealing exclusively with flotation reagents, and many of these embrace from two or three up to a score or more of specific compounds. The exact number of compounds actually finding a practical use in flotation would be difficult to determine, though the U. S. Bureau of Mines gives an annual list by groups.

Jan 1, 1938

By D. H. Thompson, A. W. Tracy

E. A. ANDERSON*—At the outset, I note that you are using a humid atmosphere containing ammonia but that you make no reference to the variable of carbon dioxide content. Edmunds in his work in this laboratory found very marked effects on the rate of failure due to variations in carbon dioxide in the environment. This point is, of course, strongly related to the overall corrosion rate problem since the role of the carbon dioxide seems to be to permit the formation of hygrogroscopic salts which give a controlled moisture film on the specimen surface, which in turn seems to support the intergranular penetration more consistently than would otherwise occur. (2) Your results with various copper binary systems are very striking. It is curious, however, that the time-to-failure minima all occur at percentages of the alloying element which are considerably below the solubility limits as given in the conventional equilibrium diagrams. If your theory regarding the presence of these impurities in some concentration in the grain boundaries is correct, then either the existing diagrams are not accurate in the room temperature region, or there is a difference in solubility in the grain boundaries as compared -with the grains. A study along these lines might be very revealing. (3) The undesirable effect of silicon in copper calls to mind our own observations on the influence of silicon on the stress corrosion cracking resistance of alpha brass. In this case, silicon was found to have a very marked beneficial effect, particularly when a heat treatment capable of producing a grain boundary constituent was used. I should appreciate it if in the discussion of your paper this point should arise, you would attempt to clarify the difference between the copper-silicon binaries and the copper-zinc-sili-con ternary alloys. D. H. THOMPSON and A. W. TRACY (authors' reply)—(1) We have no data on the constancy of the carbon dioxide content of the air used for the test atmosphere but have believed that the normal carbon dioxide content of the air was as constant as could be obtained by using Edmunds' method of removing carbon dioxide from the air and then adding a measured quantity. In any event, the test atmosphere was the same for all specimens in a test run. We agree with Mr. Anderson that the carbon dioxide content is important in the formation of a hygroscopic film on specimens. (2) We can imagine that there could be a concentration of solute atoms at the grain boundaries which would be so small that present methods would not detect it even if it exceeded the solubility limit of the alloy. There could be somewhat greater solubility at the grain boundaries for an interstitial solute. There is a possibility that phosphorus dissolves in this way but we believe that none of the other solutes studied does. In our present studies we hope to find out something about conditions at the grain boundaries of some of the systems mentioned in the paper. (3) Mr. Anderson points out that silicon brass, which has had a high temperature heat treatment followed by a quench. is highly resistant to stress-corrosion cracking. Although the test conditions used by Anderson* et al were different from our test conditions, it is noted that the silicon brasses which had not had the special heat treatment were less resistant to stress-corrosion cracking than copper containing approximately equal amounts of silicon. G. R. GOHN†—Nonferrous metallurgists and particularly, materials engineers, have been accustomed to thinking

Jan 1, 1950

By R. A., Pallanch

SO many variations of lead-zinc ores occur in nature that it is impossible to state any rules that will apply to the concentration of ores of this type. Some have lead and zinc in approximately equal amounts; others may have pre- dominant amounts of one or the other metal. There are gradations from all sulfide to completely oxidized minerals. Some such ores carry little pyrite, others contain much more pyrite than they do lead and zinc combined. The behavior of ores in flotation is largely a function of their lead-zinc ratios. their content of pyrite or pyrhotite, the nature of existing soluble salt conditions, the character of the gangue constituents: and the speed with which the minerals float. For the purposes of this paper only those lead-zinc ores handled commonly in present-day flotation practice will be considered. These are practically all-sulfide ores with relatively minor degrees of sulphatization or oxidation.

Jan 1, 1936

By Manning W. Cox

Van Stone mine area is situated at the head of Onion Creek on the northwest flank of Gillette Mountain, Stevens County, Washington. The di strict was found during World War I, but the mine did not come into production until 1952. Production to the end of 1965 was 2,242,960 tons of ore that yielded 10,700 tons of lead concentrates and 120,000 tons of zinc concentrates. The area is part of the Selkirk Mountains Zinc-Lead Belt, or Kootenay Arc, extending from near Revelstoke, British Columbia, to Colville, Washington. A thick but incomplete section of Paleozoic marine formations occurs in the Kootenay Arc and is overlain by marine and continental Mesozoic formations. Both are invaded by Late Mesozoic-Tertiary batholiths. The belt is characterized by open complex folding and extensive high-angle and local thrust faulting. Principal ore deposits occur in the highly deformed carbonate rocks of Cambrian age-the Maitlen (Laib) and Metaline formations. The Van Stone mine occurs along a steeply S-shaped fold lying between the Kaniksu Batholith on the west and the Rogers Mountain Fault, a northeast-trending fault on the west flank of the Gillette Mountain Anticline, to the southeast. The fold is cut by northeasttrending faults containing notoriously irregular lamprophyric, diabasic, and pebble dikes. The host rocks, lower Paleozoic dolomites, are decolorized, silicified, and silicated in the mine area. Jasperoid and tremolite are the common alteration minerals. Other gangue minerals are barite, pyrite, brucite, calcite, and, near the batholith, pyrrhotite. Ore minerals are galena, jamesonite, and sphalerite. Ore minerals occur in bunches and pods intergrown with tremolite and jasperoid. Zinc is roughly eight times more abundant than lead. The highest ore outcrops at 3870 feet elevation, and an undeterminable portion has been removed by glacial scour. The lowest drill hole penetration has reached 3220 feet elevation. Oxidation ranges up to several hundred feet in depth and may be most closely related to pre-glacial groundwater circulation. The area of the mine was completely over-ridden by Pleistocene continental glaciers, and the present erosion surface is nearly continuously blanketed by up to 150 feet of glacial outwash.

Jan 1, 1968

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By Maurice Magee

The Ducktown ore deposits have been known, explored, and mined for 120 years. Eight massive sulfide ore bodies occur in highly folded and metamorphosed graywacke, graywacke conglomerate, mica schist, chloritegarnet schist, and staurolite schist of Precambrian age. The ore deposits are tabular bodies that have been extensively folded, generally conform to the enclosing rocks, but show local complex differences. The ore deposits, ranging in size from 250,000 tons to over 20 million tons, are composed principally of the minerals pyrrhotite, pyrite, chalcopyrite, sphalerite, and magnetite. Gangue minerals are quartz, calcite, actinolite, tremolite, hornblende, garnet, and masses of schistose wall- rock. Three fault systems are present that have influenced ore control and ore body configuration. Hydrothermal effects are evident in wall-rock alteration. Evidence of retrograde metamorphism is extensive in the wall and ore associated rock. Preliminary isotopic age dates have indicated four possible metamorphic events during the Paleozoic Era. Ore genesis is considered to be hydrothermal replacement of receptive beds, predominantly highly calcareous zones, quartzitic zones, and brecciated shear zones. Ore deposition is thought to have occurred during the Devonian Period, with later mobilization and recrystallization of the ore and gangue during Middle and Late Paleozoic times.

Jan 1, 1968

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually has been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,1 the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin" and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between [ ]

Jan 1, 1941

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980