Search Documents

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

SME's Annual Membership Report - 1961 Membership Directory

Jan 7, 1961

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By Richard H. Mote, W. C. Schroeder

The endlessly changing pattern of mineral supply and demand offers opportunity to the alert and can bring disaster to the unwary. The discovery of ore bodies, the invention of extractive processes, the provision of new transport facilities, the political stabilization of underdeveloped areas, and many other changes can increase supply dramatically. Such new outpourings of mineral wealth from ore bodies bring fortunes to their developers, and consumers frequently find their competitive positions decidedly improved by new and cheap sources of supply. On the other hand, operators of marginal properties can find competition from newly opened high-grade mines intolerable. Consumers that have depended on the products of nearby, high-cost mines may find new, remote, low-cost supplies advantageous only to their competitors. The invention of new prospecting methods can have spectacular effects. Shortly after World War I the discovery rate of petroleum pools began to decline. The leading prospecting technique of that day, the projection downward of surface reflections of geologic structure, was proving less rewarding. Prophets foretold an oil shortage in the near future. But at that very moment scientists were perfecting the application of seismic waves to reveal underground oil-bearing geologic structures. As these geophysical methods were put into commercial use the whole outlook changed-the problem of the 1930's became how to cope with the surplus from discovery, not how to meet the ever rising demand. Many lead mines were being abandoned as unprofitable about this same time because the penalties charged by smelters for the zinc in the ores and concentrates more than counterbalanced the payments for lead and silver. Then selective flotation (at the time called differential flotation) appeared,

Jan 1, 1959

By R. W. Raymond

WISH to call the attention of the Institute to a curious subject, brought to my notice last summer by Mr. Begger, the accomplished metallurgist of the smelting-works of the Boston and Colorado Company at Black Hawk, near Central City, Colorado. At these works, the richest auriferous sulphhrets of Colorado (particularly copper pyrites) are smelted in reverberatories, together with roasted tailings (iron pyrites), and the gold and silver are concentrated into a new, artificial sulphide, or copper matte, containing $1500 and upwards of the precious metals per ton, and this is shipped to Swansea. I will say in passing, that this shipment of an unrefined product, like the similar shipments from Utah and Nevada to San Francisco, Chi¬cago, St. Louis, Newark, New York, and Europe, of crude argentiferous lead or "base bullion," is not a sign of incomplete metallurgy here, but has a sound business reason. The separation of the precious metals in the West would be more expensive, to begin with ; and then it would necessitate the movement of these metals by express, at high rates and risk, to commercial centres or coining mints, while the base metals having no home market, must be shipped and sold at little or no profit. At present, the gold and silver, safely packed, as it were, in the base metals, are transported with safety as ordinary freight; and the base metals probably more than pay cost of shipment and separation. To return to the Black Hawk reverberatories. On a recent occa-

Jan 1, 1873

By R. W. Raymond

I wish to call the attention of the Institute to a curious subject, brought to my notice last summer by Mr. Begger, the accomplished metallurgist of the smelting-works of the Boston and Colorado Company at Black Hawk, near Central City, Colorado. At these works, the richest auriferous sulphurets of Colorado (particularly copper pyrites) are smelted in reverberatories, together with roasted tailings (iron pyrites), and the gold and silver are concentrated into a new, artificial sulphide, or copper matte, containing $1500 and upwards of the precious metals per ton, and this is shipped to Swansea. I will say in passing, that this shipment of an unrefined product, like the similar shipments from Utah and Nevada to San Francisco, Chicago, St. Louis, Newark, New York, and Europe, of crnde argentiferous lead or "base bullion," is not a sign of incomplete metallurgy here, but has a sound business reason. The separation of the precious metals in the West would be more expensive, to begin with ; and then it would necessitate the movement of these metals by express, . - at high rates and risk, to commercial centres or coining mints, while the base metals having no home market, must be shipped and sold at little or no profit. At present, the gold and silver, safely packed, as it were, in the base metals, are transported with safety as ordinary freight; and the base metals probably more than pay cost of shipment and separation. To return to the Black Hawk reverberatories. On a recent occa-

By V. Koump, T. F. Perzak, R. G. Olsson

Jan 1, 1965

By George J. Young

(Cleveland Meeting, October, 1912.) I. GENERAL. THE recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may he enumerated as follows: Forman Shaft fire., Gold Hill, April 21, 1903 ; shaft-house, machinery, and shaft, destroyed; loss estimated at $50,000.; Cause Unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery, and shaft in part destroyed; loss estimated it $100,000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909 ; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause ' probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started in winze ; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911 ; fire originated iii shaft-station from unknown cause; 7 men killed, and $34,¬521 damage caused. (NOTE 1.-On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and laming of the pump-room. The pump-roan in charge notified the surface, and the * Professor of Mining and Metallurgy, Mackay School of Mines.

Oct 1, 1912

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By Louis A. Carapella, William E. Shaw

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By William E. Shaw, Louis A. Carapella

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

By W. R. Barclay

IN MY general contact with industry I have become more and more impressed with the need for the closest possible co-operation between engineers and metallurgists, and particularly with the need for appreciation of the work that each group is doing to assist the other. Also, I am convinced that from time to time it. is vitally important to a true perspective of human progress in all its branches, and certainly a salutary corrective of undue optimism and pessimism to endeavor to carry the mind hack over certain periods in the advance of technical knowledge, and form some kind of broad estimate of what has been accomplished in the application of science to industry in the fields with which we, as individuals or groups, may for the time being be concerned. We cannot without some appreciable mental effort realize what our forerunners have dine For us. If the young engineer or metallurgist entering industry today could be suddenly transported to a quarter of a century ago, and be compelled to work with the materials then available and within the limitations of knowledge then attained, he would, on his return to present-day life, have a much greater appreciation of what has been accomplished before lie arrived on the scene, and, what is even more important, a far more acute sense of its inherent value to his profession. I propose here merely to indulge in a general summary of the subject of improved engineering metals and alloys rather than in details, and to deal exclusively with developments within my own experience.

Jan 1, 1938

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By David W. Brunton

I. INTRODUCTION. THE list of our past-Presidents comprises the names of runny who, in their official addresses, have sketched the current progress of the arts and professions with which they were familiar. Such addresses are, in my judgment., highly useful, setting forth the results of our own work as a. society, and recalling to our minds the particular lines in which discussion would prove most fruitful. . Following this course with some hesitation, I venture to offer an outline of the recent improvements and the present situation in minim and metallurgy in the Western United States. The wonderful advances in mechanics, chemistry, and electricity have all combined to aid these arts to such an extent that. progress during the last decade has undeniably been more rapid than ever before in the history of the profession.. In all mining countries improved transportation-facilities, in many instances called into existence by the traffic created by the mines themselves, have done much- to enlarge the. field of operations by the reduction of freight-, operating- and living-expenses, thereby bringing lower-grade properties into the producing class. Under normal' conditions, as the age of a district in¬creases, all these differentt factors should combine to off-set. the augmented costs attendant on deep mining, and greatly tend to prolong the profitable life of the mines. The more recent and important improvements in our Western mining-practice which have contributed most toward the advancement of the art may be briefly summarized as follows; but, before beginning this portion of ray address, I wish to thank most heartily the many engineering friends who have so

Sep 1, 1909

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1' shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter's' original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.