Search Documents

By Orville R. Lyons

DISCUSSION Judson S. Hubbard (The Humphreys Investment Co., Denver)—In this very interesting paper several brief references are made to the Humphreys spiral, a device used for cleaning fine coal. In Table I, Plants 76 and 77, data are given on spiral performance treating Raton and Trinidad coal. The fine coal, as fed to the spiral in these instances, is actually a table middling, hence the more easily treated material was previously removed and a large number of particles were present which were difficult to clean. Mr. W. M. Bertholf of the Colorado Fuel and Iron Co. presented a paper in February, 1946, Cleaning Table Middlings from a Coal Washery with the Humphreys Spiral Concentrator, from which I quote: "In considering the results of our tests it should be noted that the feed was our table middling, and that any real separation is a 'moral victory' as there is little material that could properly be called coal and practically no heavy rock, the consequences being that previous attempts to clean the middling have not at all been successful." Referring again to Table I, Plants 72, 73, 74, and 75, these data were obtained by Yancey and Geer and others and presented at the February 1950 Meeting, AIME, in a paper entitled Laboratory Performance Tests of the Humphreys Spiral as a Cleaner of Fine Coal. Results shown for those tests involve all particles from 8 mesh through the colloids, which admittedly is not an ideal situation for spiral feed if much refuse is contained in the —80 mesh or —100 mesh size range. As an illustration of the effect of treating too broad a size range, let us consider Plant No. 75, Kentucky No. 9 seam. Spiral feed was 8 mesh x 0. Now had this been 8x100 mesh the percentage of misplaced material would have been 8.0 pct instead of the reported 15.26 pct. Similar comparisons can be made on the other data presented with respect to the spiral. Other types of equipment show a similar trend in that whenever too fine a size is treated in a given unit process the percentage of misplaced material increases. Since the spiral is working near the finer end of the size range, it will sometimes be advantageous to treat the entire range of —8 mesh material rather than to deslime and make a fair showing on, say, the +80 or + I00 mesh. Desliming is subsequently done in any case in the dewatering or thickening operation. Results obtained by spiraling any given coal depend on factors too numerous and complex to discuss here, but there are strong indications that proper preparation of feed to the spiral can improve results obtained on some of the raw coals tested. This is clearly pointed out at the end of the aforementioned paper by Yancey and Geer. "The spiral is an extremely simple device which involves no moving parts and is constructed almost entirely of unmachined castings. Since it is such an uncomplicated mechanism, operation is simple and virtually foolproof. These characteristics, which go far toward insuring low cost operation, are attractive attributes in any coal cleaning unit." Certain equipment used in conjunction with the spiral has resulted in a decrease in the percentage of misplaced material, notably in actual practice the launder screen which is used to remove objectionable high ash fines from a spiral-washed coal product. Private correspondence with the U. S. Bureau of Mines has intimated that an additional yield of coal is possible by flotation of the spiral middling. Possible future improvements and developments may result from other methods now under consideration. Finally, some compromise must be made between the best metallurgical performance and the best practical or economical results. Mr. Lyons emphasizes in his summary this objective of overall economy in selection of equipment. G. B. Walker (American Cyanamid Co., Stamford, Conn.)—I had the pleasure of reviewing the draft of this paper and my curiosity was aroused by the data given for Tromp plants, in that all of the examples shown appeared to be 2-product separations, whereas all the Tromp plants with which I am familiar have been 3-product units. The data given for plants No. 101 and 102 appear to be taken from Tromp's brochure on his process and represent the results obtained at the Dominale plant in Holland which was operated for many years by Mr. Tromp. The plant, which was designed to treat 58 tons per hr, was sampled while treating 35 tons per hr of 3Y4x-in. coal. Example 101 appears to conform to what would result if the middling product were calculated into the refuse product, while Example 102 represents the calculation of the middling into the coal product. It is believed that Examples 103 and 104 represent the operation of the Willem-Sophie Mine in Holland recalculated on the same basis. In checking the English examples given by numbers 14, 15, 16, and 17, the same procedure seems to have been followed. These results have, apparently, been taken from an article in Colliery Engineering in August 1941, describing the initial operation of the Williamthorpe Colliery of the Hardwick Colliery Co. Two vessels are employed in this plant, one to treat soft coal and one to treat hard coal. Example No. 14 presents the results that could be obtained from the soft coal bath if the middling were calculated into the refuse, and Example 15 the results when the middling is calculated into the coal. Examples 16 and 17 represent the same expedient in the case of the hard coal bath. Of interest to this discussion is the fact that during the past year the Simon-Carves Engineering Co. in England has installed in the Williamthorpe plant their new "Sim-Car" medium cleaning system which is based on magnetic extraction and control and which is licensed under the Heavy-Media Separation Processes patents by the American Zinc, Lead and Smelting Co. This system has been described in the December 1951, issue of Colliery Engineering. It is reported that since the Williamthorpe Colliery was changed from the Tromp system of medium cleaning to the Magneto-Motive method of medium control the opera-

Jan 1, 1953

By Harold A. Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand- book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By E. F. Kingsbury

ONE of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and. the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which. were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consumption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. SUBSTITUTES FOR PLATINUM During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and' comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper materials, and the other, the development of materials of superior electrical performance. The merit, of a contact metal has been assumed to be dependent on its infusibility, and since the more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

Jan 1, 1928

By J. H. Nead

Discussion of the paper of J. H. NEAD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2341 to 2357. E. D. CAMPBELL, Ann Arbor, Mich.-Any one at all familar with research work can at once see that Mr. Nead has condensed into his tables and curves the results of a carefully planned set of experiments which must have involved a great amount of work on his part. He deserves much credit for the way in which he has carried out these experiments, for it is to the results of such systematic experimentation that we must look for further knowledge of the underlying causes which determine the physical properties of steel. It will probably be many years before we have sufficient knowledge of all the factors of the problem of the constitution of steel, but every set of carefully carried out experiments such as Mr. Nead has made adds something to our knowledge and brings us a little nearer to the final solution of the problem.

Jan 5, 1916

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

Since the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error. Introduction The steady-state flow of gas through a porous material—that is, flow wherein the boundary conditions do not vary with time—is subject to analytical solution. Muskat1 has shown that the general differential equation is simply the La Place equation in P2. Direct solutions may be at once obtained. The unsteady state, on the other hand, is not analytically reducible. Since nearly all phenomena of practical interest in gas production involve flow in the unsteady rather than in the steady state, it has been necessary to derive approximate Solutions to the general equation. The validity of such approximations has not hitherto been adequately tested. In the experiments to be described a simple, closed, linear system is substituted for the real complex gas field. The general results, however, are independent of the geometry Of the system' The problem studied is the rate of production, and the accompanying variations in pressure, when one end of a linear porous system is opened to the atmosphere and permitted to produce to exhaustion. An approximate solution to the general differential equation, based upon the assumption of an "infinite series of steady states," is then applied to the results to determine the validity of this method of dealing with actual reservoirs. Theoretical Considerations The fundamental differential equation governing the flow of a gas through a Porous medium can be derived easily from the equation of continuity, Darcy's law, Boyle's law and a statement of the thermo-dynamic nature of the flow. For isothermal flow it is: d2P2/dx2 + d2p2/dy2 + d2p2/dz2 = 2fµ/K dP-dT

Jan 1, 1942

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

Since the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error. Introduction The steady-state flow of gas through a porous material—that is, flow wherein the boundary conditions do not vary with time—is subject to analytical solution. Muskat1 has shown that the general differential equation is simply the La Place equation in P2. Direct solutions may be at once obtained. The unsteady state, on the other hand, is not analytically reducible. Since nearly all phenomena of practical interest in gas production involve flow in the unsteady rather than in the steady state, it has been necessary to derive approximate Solutions to the general equation. The validity of such approximations has not hitherto been adequately tested. In the experiments to be described a simple, closed, linear system is substituted for the real complex gas field. The general results, however, are independent of the geometry Of the system' The problem studied is the rate of production, and the accompanying variations in pressure, when one end of a linear porous system is opened to the atmosphere and permitted to produce to exhaustion. An approximate solution to the general differential equation, based upon the assumption of an "infinite series of steady states," is then applied to the results to determine the validity of this method of dealing with actual reservoirs. Theoretical Considerations The fundamental differential equation governing the flow of a gas through a Porous medium can be derived easily from the equation of continuity, Darcy's law, Boyle's law and a statement of the thermo-dynamic nature of the flow. For isothermal flow it is: d2P2/dx2 + d2p2/dy2 + d2p2/dz2 = 2fµ/K dP-dT

Jan 1, 1942

By A. Lee Barrett

SO commonplace that they are seldom noticed, mining-machinr, bits have a definite and important bearing on the cost of coal production. At the average mine many thousands of bits are used during the year. The actual cost represented by the purchase of the bits used, as well as that of sharpening and handling them, represents a considerable sum of money. From the point of view of indirect costs they are important, as the lack of good bits at a mining machine can seriously impair production. Good bits tend to ensure an adequate supply of coal. Classes OF Bits Mining-machine bits may be divided into three general classes, based on shape and method of use: (I) chisel, (2) pick-point and (3) one-use. The chisel and pick-point bits are shown in Fig. I. The so-called "chisel" bits were made of steel of various sizes and were sharpened to a wide chisel cutting edge. Few of this type of bit are used, except in places where coring is very bad. Sometimes chisel bits are used with standard bits to help cut out the core. The "pick-point" bit is widely used today. Normally it is made from ½ by I-in. steel, is about 4½ in. long when new, has a rake angle of about 25°, a front clearance of about 23O, a side clearance of approximsteji 8".' There are many variations in the shape of this bit, depending on the ideas of the individual that may be dressing the dies of the bit machine. This bit has been generally used for many years and at present, in one form or another, is by far the most popular bit used in coal mines. This bit usually is made from 0.85 carbon steel, although in recent years some alloy-steel bits have made their appearance. At present, carbon-steel bits are frequently tipped in. hard facing materials. A third class of bits might be called the L'one-use" bit; that is, a small bit that is used once and then thrown away. These bits have two or three points, are usually made from 0.85 carbon steel and sometimes from higher alloys. Recently some. of them have been tipped with hard facing material. Most of them were used at first with special

Jan 1, 1942

By A. Lee Barrett

SO commonplace that they are seldom noticed, mining-machinr, bits have a definite and important bearing on the cost of coal production. At the average mine many thousands of bits are used during the year. The actual cost represented by the purchase of the bits used, as well as that of sharpening and handling them, represents a considerable sum of money. From the point of view of indirect costs they are important, as the lack of good bits at a mining machine can seriously impair production. Good bits tend to ensure an adequate supply of coal. Classes OF Bits Mining-machine bits may be divided into three general classes, based on shape and method of use: (I) chisel, (2) pick-point and (3) one-use. The chisel and pick-point bits are shown in Fig. I. The so-called "chisel" bits were made of steel of various sizes and were sharpened to a wide chisel cutting edge. Few of this type of bit are used, except in places where coring is very bad. Sometimes chisel bits are used with standard bits to help cut out the core. The "pick-point" bit is widely used today. Normally it is made from ½ by I-in. steel, is about 4½ in. long when new, has a rake angle of about 25°, a front clearance of about 23O, a side clearance of approximsteji 8".' There are many variations in the shape of this bit, depending on the ideas of the individual that may be dressing the dies of the bit machine. This bit has been generally used for many years and at present, in one form or another, is by far the most popular bit used in coal mines. This bit usually is made from 0.85 carbon steel, although in recent years some alloy-steel bits have made their appearance. At present, carbon-steel bits are frequently tipped in. hard facing materials. A third class of bits might be called the L'one-use" bit; that is, a small bit that is used once and then thrown away. These bits have two or three points, are usually made from 0.85 carbon steel and sometimes from higher alloys. Recently some. of them have been tipped with hard facing material. Most of them were used at first with special

Jan 1, 1942

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

By E. G. Williams

Manganese-ore has been found upon the Isthmus of Panama throughout' a region of nearly three hundred square miles, over the greater part of which, however, it is known only in small bodies without commercial value. Only six mines, controlled by two companies, have actually shipped ore, although a large area has been taken up in miningelaims. The ore-bearing region extends along the coast of the Carib. bean Sea, beginning on the west near Puerto Bello and extending easterly about 35 miles toward Point San Blas. Ore has been discovered in the interior, at a maximum distance of about 10 m. from the coast. Fig. 1 is a map of a portion of the Isthmus

Jan 1, 1903

By Robert F. Mehi

The mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystallinc symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by slip along atomic planes.' This slip may be inhibited in a number of ways: by the interatomic forces of, cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by latticc distortion caused by solid solution formation or by mechanical strain; by the intercrystalline boundaries whcrc slip is restrained, probably by the non-registration of the atom planes in adjacent crystal1ites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.5 In pure metals, and perhaps also in solid solutions, the atom planes of easiest slip are those exhibhing the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be pre-dict,ed from the analysis of the lattices. Concerning the interatomic forccs, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bot-tone,5 correlate the hardness of the pure metals with the atomic volume,

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By David R. Maneval, H. B. Charmbury

At the turn of the century, iron and coal were the keys to industrial prosperity. At that time, Pennsylvania was the leading mineral producer in the Country, producing 200,000,000 tons of coal in a typical post-World War I year. Close to 90% of the Nation's energy was generated by coal. Today, coal accounts for but 22% of the energy generated, leading to a drastic reduction in Pennsylvania coal output. In contrast with the post-World War I days, 1964 figures showed a drop in production to 93,846,480 net tons. This huge decrease has created a serious economic problem in a state so much dependent on the coal industry. Along with the reduction in coal production, employment has dropped considerably through these years (the number of miners alone has gone from 280,011 to 43,149), thus causing a heavy burden of supporting the unemployed on the taxpayers. As far back as 1939, coal operators and economists saw the problems on the horizon and the need for improvement. Realizing that research was a way to improve and stabilize the industry they demanded legislative action. The Legislature reciprocated with a small grant to The Pennsylvania State University with the provision that each State research dollar be backed with one from the industry. This initial grant laid the foundation for the further growth in coal research.

Jan 3, 1966

By M. J. Saarivirta

A high-purity copper-zirconium alloy system was imesti-gated. The zirconium content of the alloys studied varied from 0.003 to 0.23 pet. The solid solubility of zirconium in copper and some physical and mechanical properties of the alloys have been determined. By proper heat treatment, Cu-Zr alloy can develop a high electrical conductivity and resistance to softening at temperatures up to 500°C (930°F). This combination of desirable properties makes this alloy superior, to other com-merzcrrl copper base alloys for- use in the electrical conductor field. DEMAND for high conductivity copper alloys that retain their mechanical properties at elevated temperatures is growing rapidly. At present, copper-base alloys such as copper-silver and copper-chromium are used where these characteristics are required. As an example, commutators in electric motors are often made of these alloys. However, the life at elevated temperature of commutators made of copper-silver alloys is much shorter than the life of the same part made of copper-chromium and copper-zirconium alloys. Copper-silver alloys are subject to creep and subsequent failure when the service temperature exceeds several hundred degrees centigrade. Use of copper-chromium alloys has been known for the past several years, but little information is available in the literature concerning the properties of alloys in the copper-zirconium alloy system. Some work had been directed toward determining the solubility of zirconium in copper as well as determining properties of the Cu-Zr alloys. These investigations have revealed the superior high-temperature and electrical conductivity properties of copper-zirconium alloys over copper-chromium alloys. The United States Metals Refining Co., Carteret, N. J. has recently produced OFHC R copper-zirconium alloys for experimentation and evaluation. Because OFHC R copper contains no appreciable oxygen, no harmful oxides are formed and the full benefit of Zr as an alloying addition is obtained. This paper describes the results of this work. It contains room-temperature and some high-temperature data which have been obtained after various processing techniaues. Actual elevated temperature properties are being determined and will be reported in a separate paper. Preliminary results obtained at elevated temperatures suggest that the Cu-Zr alloy is superior to other high conductivity copper-base alloys. WORK PROCEDURE The high-purity oxygen free (OFHC R) copper-zirconium alloys with zirconium content ranging from 0.003 to 0.23 pct were cast into 4-by 4-in. wirebars by both continuous casting and conventional casting methods. Zr was added in the form of a master alloy containing 30 pct Zr and 70 pct Cu. Castings were analyzed for zirconium and nine bars containing various amounts of zirconium were selected for this study. The results of analyses and the sample numbers are given in Table I. Typical analyses of OFHC R copper are also shown. The following properties were studied: A) Solid solubility of zirconium in copper. B) Effect of zirconium on properties of copper. C) Effect of combined working and heat treating on properties of Cu-Zr alloys. The solid solubility of zirconium in copper was determined by metallographic techniques. Specimens for this phase of the investigation were hot rolled at 900oC (1650oF) to 0.250-in. rod. The rolled rods were cut into 2/3-in. long specimens and solution annealed at 950 °C (1740°F), 980°C (1795 °F). and 1020 °C (1870 °F) for 6 hr and quenched in water. In order to find the solid solubility limits at lower temperatures, the homogenized specimens were reheated at various temperatures for 1 hr and quenched. The physical and mechanical properties were determined on 0.250 in. rod, 0.132- and 0.081-in. wires. The wires were cold drawn from the 0.250-in. rods after they were solution annealed at 980 °C (1795°F) and quenched in cold water. Mechanical and electrical properties were determined on cold drawn and

Jan 1, 1961

By H. L. Couch, J. D. Lubahn

In decarburized mild steel, the strain hardening arising from 1/2 pct strain can he partly recovered by subsequent heating, even though re crystallization or grain growth does not occur. This recovery varies from 5 pct in an hour at room temperature to 70 pct at 800°C. The variation with temperature was qualitatively similar to that reported for copper, but occurred at lower temperatures. Except for the initial portion (Bazdschinger effect), the stress-strain curve following recovery can be superimposed on the original curve by shifting it to the left. In other words, the tensile behavior is essentially the same after straining and heating as if there had been less strain and no heating. The importance of this observation in understanding simultaneous deformation and recouery is explained. AN earlier investigation1 on copper showed that strengthening due to strain hardening was augmented by heating at moderate temperatures, but was diminished by heating at higher temperatures, Fig. 1. Auxiliary experiments1 indicated that recovery and strain aging are independent processes, which may proceed simultaneously, and whose effects are additive as indicated in Fig. 1. In order to study recovery by itself, similar tests were made on decarburized mild steel, where strain-aging effects are known2 to be absent. MATERIAL, TESTING PROCEDURE The specimens were made from rimmed, hot-rolled SAE 1020 steel 0.040 in. thick, by stamping out rectangular blanks and end holes, Fig. 2, and pack milling the reduced section. These were wet-hydrogen treated2 for 16 hr at 720°C to remove carbon and nitrogen completely and then heated 1 hr at 850°C in vacuum to stabilize the grain size. Auxiliary ex- periments showed that heating up to 800°C will not cause grain growth. They were prestrained 5 to 7.5 mils per in. using the special grips shown in Fig. 2. Such small strains are less than the "critical" strain for recrystallization and, therefore, will not cause recrystallization, even at high temperature. The recovery treatment after prestraining and before the retesting consisted of heating for 1 hr in wet hydrogen at the desired temperature. In one test, Huggenberger gages were used to define more accurately the loading and unloading curves. Fig. 3 illustrates the creep during the early stages of unloading, the hysteresis due to cold stretching, and removal of hysteresis by heating.3 RESULTS The load-deflection curves had ratner widely differing shapes for different specimens, both before and after the recovery treatment. Some specimens showed perfectly smooth curves, Fig. 4, while others exhibited an inflection more or less suggestive of a yield point (Fig. 4 shows all extreme case). Some curves were much steeper than others; Fig. 5 shows two extremes. Some additional ex-

Jan 1, 1960

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By ALBERT C. RUBEL

RECENT developments in the use of the core barrel in rotary drilling have led to its wide application in all types of development. Its use is essential to the wild-catter and a valuable guide and check even in the most closely developed areas. A perfect core would be an unbroken sample of formation whose length is equal to the amount of hole made by the core barrel, whose diameter is great enough to show the lithologic character, texture and attitude of the material encountered, whose formation is so unaltered in character and so free of contamination from outside sources that it represents a true and complete sample of the formation penetrated. From such a core it would be possible to determine the lithologic character and economic importance of the formation, whether it is oil bearing or barren, the nature and attitude of the sands and shale bodies, valuable fossil evidence and other points which would assist in the correlation or in the selection of suitable points for water shut off or production.

Jan 1, 1924

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937