Search Documents

By C. Allen Born

INTRODUCTION As the title of this paper suggests, the author does not believe that risk can be managed. Rather, the objective is to identify the risk which will be present in a given venture and assess the level of that risk which is acceptable. More often than not, the risk which is present is subject to little or no modification. After identifying and measuring the risk a corporation will decide to accept it and proceed in such a way that it will be less exposed, or it will decide not to proceed at all. The exercise for a corporation is different only in degree from everyday judgements made by average people in average situations. However, that word "degree" means that it is considerably more complex on the corporate level. There is good reason for the additional complexity of corporate risk evaluation. The variables influencing a company's decision can be more numerous and the penalties for miscalculation much greater than those normally encountered by an individual. It should be understood that no analysis of risk, certainly not one as brief as the following, can do more than touch on some of the high points. Before examining the sorts of risk which affect the development and operation of specific mines, let us consider the broader aspect of the term with which mining companies, and all other business corporations, must deal. Companies must determine their long-term objectives and strategies within the context of a constantly changing world. To plot their direction they must attempt to read the future by seeking answers to questions such as: How will society evolve? Which businesses will thrive? In which of these should we place our emphasis? If a company hopes to be around five or ten years from now it must make the attempt to answer such questions in order to judge the impact of changing patterns in the evolving business environment. Information is available to allow the lessons of the past to be projected on the future. We have data on birth rates, economic booms and busts, patterns of conflict within and between nations, drought and other forces of nature as well as individual events which cannot be predicted, but which over time, do seem to occur in regular cycles. Ultimately the question "where will we be and what will we be doing a decade from now?" must be answered by one or more senior people with responsibility for the company's future. The compilation and interpretation of hard data by competent support staff, can only be used up to a certain point in determining future corporate strategy since there will be alternative possible futures and a high degree of risk will always remain. At this point those elusive qualities of experience, instinct, and - "gut feeling" - become important factors in choosing a long-term corporate direction. The goals of a company have a significant bearing on its attitude towards risk. This in turn dictates the "hurdle rate of return on investment" which a project decision-maker will require. The hurdle rate is the minimum-discount-percentage-rate applied to forecast cash flows to give a present value of zero to the All-Equity-Funded Investor. The feasibility study for a project is a fundamental tool in the management of risk. An experienced team has an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of conservation is built in at all levels of study data and, if the project is technically feasible, the hurdle rate becomes a catch-all measure of risk in a base-case project cash flow.

Jan 1, 1985

By R. C. Ferguson, B. Bernstrom

R.C. Ferguson (District Manager, Hardinge Company Inc., Hibbing, Minn.) — In the opening paragraph of Mr. Bernstrom's paper he stated that the Cascade mill performance information is preliminary. With the completion of the 1962 operating season, more reliable performance information became available. The main bearings, which had been damaged, were reconditioned at the factory. New Gatke bearing bushings with a 120° are of contact were supplied. Provision was made to introduce high pressure lubricant at two points in each bearing. New spherical bearing balls that operate in spherical seats were aligned at the factory and held in place by several setscrews to aid in installing the bearings in the field. The screws were not loosened prior to, or during, operation; therefore, the bearings operated as rigid bearings. The lubricant cooling system was changed to the cooling tower type to provide lubricating water of a suitable temperature. Another refinement consisted of installing a device to add a set percentage of soluble oil to the make-up water.

Jan 1, 1963

HENRY M. HOWE, Bedford Hills, N. T. (communication to the Secretary?).-The authors valuable results as to the effects of the air-hardening temperature on high-speed steel may be summed up thus: Influence of Rising Air-Hardening Temperature on. High-Speed Steel Air-hardening microstructure Cutting Properties temperature S Austenite Grain Free Carbide Grains Boundaries Too low Small or Narrow Maximum Too soft undeveloped Intermediate, Well-developed Intermediate Little or even Best correct none Too high Coarse hide, even with Minimum . Weak, brittle, three-rayed crumbling stars Here the suggestion is that as the air-hardening temperature rises it causes two prominent effects, one helpful and the other harmful, the increase of the former exceeding that; of the latter up to a certain point, at which the steel is most useful, and then in turn being outrun by it. The first is the progressive dissolving of the free carbide in the austenite, increasing the stability of the red-hard state. The second is the progressive coarsening of the grains, and thickening of the intergranular cement, developing at last into spandril-like three-rayed stars of the 1,288° specimen. (2,350° F.) of Plate D, thus giving clear proof of incipient fusion, that is of crossing the solidus. This causes intergranular weakness. The individual grains may have great red-hardness, but they do not cohere. They approach the condition of a bag of emery grains.

Jan 6, 1917

T. R. HARRISON, Washington, D. C. (written discussion *).-Ad-vantage will be taken of this occasion to mention briefly a form of double potentiometer which has been used at the Bureau of Standards for about 2 1/2 yr. in calibrating thermocouples. The calibrations referred to are those made by comparison to standard couples. In order to insure equality of temperature between the couples, the junctions are fused together; consideration of fundamental principles will show that this introduces no error. Two separate potentiometers are used, one connected to each thermocouple, and each potentiometer is provided with a reflecting galvanometer. The two spots of light are reflected on to a single scale, the galvanometers being set in such a position that the spots coincide on the scale at a point marked zero when the circuits are open or when the potentiometers are balanced. By setting one potentiometer to a desired value and adjusting the other so that both spots pass across the scale together as the temperature rises or falls, simultaneous readings are obtained. By making observations first with a rising temperature and then with a falling temperature, the rates of rise and fall being approximately equal, and taking the means of the results found, several minor errors such as those clue to differences in the time lags of the two systems, etc., are eliminated or greatly reduced. The differences between the values

Jan 12, 1919

By I. Fatt

Study of a model which contains "dead-end" pore volume indicates that pressure transients are influenced by the amount of dead-end pore volume and by the resistance of the flow path between the dead-end pore volume and the main flow channels. A semi-empirical method is demonstrated that makes possible measurenment of the volume in the dead-end pores and the total pore volume. The difference between these two volumes is the volume of the flow channels. An indication of the flow resistance between the dead-end pore space and the lain flow channels is also obtained. INTRODUCTION In some engineering calculations the distribution of pore volume in a petroleum reservoir need not be known. For example, a material balance calculation treats a reservoir as an oil-filled tank. In other calculations the distribution of pore volume appears implicitly through use of the porosity and the relative permeability and capillary pressure characteristics. It is the purpose of this paper to point out that under certain conditions the exact distribution of pore volume must be known in order to interpret correctly transient flow behavior. Pressure transients during single-phase flow in porous media are usually said to obey differential equations of the form

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, get in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has ken mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been almost entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is anlazing that the iron companies will persist in sending abroad under heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests mere canducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition: Water,....2.68 Silica,..........65.48 Iron oxide,.........2.10 Alumina,.........15.02 Magnesia,... 15.35 10061

Jan 1, 1882

By Tsuyoshi Kawahara

INTRODUCTION A medium sized mine like the Mamut is not considered a standard size porphyry copper mine. If the infrastructure such as roads, bridges, port facilities, power supply, etc. is inadequate, construction cost per ton of copper produced will be unavoidably high. At the Mamut mine, all efforts had been concentrated to minimize construction cost and overcome an adverse natural environment. Consequently, it was inevitable that the amount of equipment and other arrangements were far from ideal. Some of the construction work was carried out by Japanese contractors, but most was done by local contractors, especially the buildings, installation of machines, roads, and tailings disposal dam, etc. All construction works, including a test run of an 18 000 t/d capacity mill, were completed in September 1975. The total development cost was about 100 million including interest converted into principal during the construction period. HISTORY The Mamut copper mineralization was discovered in mid-1965 by the United Nations' Labuk Valley Project. Following this discovery, further exploratory works, including geochemical survey, pitting, and shallow diamond drilling, which were carried out by the Geological Survey of Malaysia, revealed the existence of a disseminated copper mineralization of porphyry type. In July 1968, I.P. survey and deep-hole diamond drilling were

Jan 1, 1976

By I. Cornet

INTRODUCTION WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943 1; it has been released for publication by the O.S.R.D. SCOPE OF THE INVESTIGATION The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with the notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and M. For comparison, extrusions of aluminum alloy 24S-T, cast bars of aluminum alloy I22-T2, and cast bars of magnesium alloy C were also tested, The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of the tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the changing hardness, tensile strength, microstructure, and notch sensitivity observed. EXPERIMENTAL TECHNIQUES AND PROCEDURES Tensile Testing Bars used for axial loading were machined with 3/8 in.- and with 1/4-in. minimum diam, and included specimens with 6o° V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These V-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1948

By J. R. Eckel

It has long been known that mud properties affect drilling rate and that drilling with water is as much as six to .seven times faster than with mud. However, it is not known why drilling rates with mud are lower. Recent studies show what fluid properties govern microbit drilling rate and also provide a quantitative correlation of these fluid properties and hydraulics with microbit drilling rate. All the microbit tests reported in this paper were made with a low permeability (about 10 md) limestone. They were conducted at constant bit weight and rotary speed with varying fluid properties, flow rate Q and nozzle dinnteter d. The tests showed that (1) drilling rate in a given system with constant circulating rate and nozzle velocity is a function of the kinematic viscosity [viscosity /density, (cp)/ p (density)] of the drilling fluid measured at near bit nozzle shear rates; (2) the combined effect of fluid properties and hydraulics on microbit drilling rate is defined by a Reynolds number function (kQp/dp); (3) for the same kinematic viscosity, drilling rate is independent of solids content; and (4) for the same kinematic viscosity, drilling rate is independent of fluid loss. INTRODUCTION The fact that mudding up reduces rate of penetration is well known, but the reduction varies from well to well. The rate with mud may be 80 percent of the water rate or it may be as low as 15 percent. Since this reduction of up to seven-fold takes place under conditions of constant bit weight, rotary speed and mud circulating rate in a uniform formation, it can only be a result of the change in fluid properties. Previous work1-" both in field tests and in laboratory microbit tests) showed that drilling rate with mud is lower than with water (Figs. 1 and 2). Microbit tests also confirm, at least qualitatively, the field observation that drilling rate slows with increased pressure differential from borehole to formation (Fig. 3). The qualitative effect of drilling rate of bit weight, rotary speed and rate of mud circulation are also the same for the field and microbit rig. For these reasons, the industry generally accepts microbit results as being qualitatively meaningful in terms of field application.

Jerome L. Boyer, Reading, Chairman; William L. Sheafer, Pottsville, Secretary ; Levi Quier, Reading, Treasurer; Robert Allison, Port Carbon; James Archbald, Jr., Pottsville; William Atkins, Pottsville; D. P. Brown, Lost Creek; William McH. Boyer, Rending; Albert Broden, Reading; George Brooke, Birdsboro; Frank Carter, Pottsville; H. P. Cooper, Pottsville ; J. H. Carpenter, Reading; E. S. Cook, Pottstown; B. Halberstadt, Pottsville; Hakon Hammer, Pottstown; J. Hartshorne, Stowe; M. P. Janney, Pottstown; R. C. Luther, Pottsville; N. Muhlenberg, Reading ; W. H. Morris. Pottstown ; George L. Norris, Reading; G. H. Potts, Pottstown ; H. Potts, Pottstown; S. M. Riley, Ashland ; J. S. Robeson, Pottstown ; Jas. P. Roe, Pottstown; A. W. Sheafer, Pottsville; Heber S. Thompson, Pottsville; Bard Wells, Pottsville; E. C.Wagner, Girardville; N. B. Wittman, Birdsboro. Reception Committee.— George Brooke, Chairman; Robert Allison, J. H. Carpenter, Edgar S. Cook, R. C. Luther, W. H. Morris, H. S. Thompson. Hotel Headquarters.—The Neversink Mountain Hotel, near Reading, Pa. All sessions were held in the hotel. The opening session was held on Tuesday evening, October 11. Mr. Jerome L. Boyer, Chairman of the Local Committee, called the meeting to order, and introduced Mr. John F. Daniel], Jr., VicePresident of the Reading Board of Trade, who delivered an address of welcome, in the course of which the industrial and commercial importance of the city was effectively outlined by skilful use of the statistics of leading branches. From this statement the following particulars are condensed for preservation: The Board of Trade has about 300 members. The annual value of the manofttctures (taking mainly the figures of 1891) is as follows: Iron manufactures, about $16,000,000 (including boilers and flues, $323,000; hardware, locks and butts, $1,650,000; pig-iron, wrought-iron pipe and machinery, $8,400,000; beams, bridge-work and steel, $4,000,000; bolts, nuts, rivets, etc., $1,000,000; stoves, $659,000); silk and cotton goods, $1,725,000; boots and shoes (one concern only), $150,000; ropes and cordage, $600,000; fire-brick, terra-cotta and glass, $320,000; wool and fur hats, $3,000,000; cigars (105 millions), upwards of $3,150,000. The street and elec-

Jan 1, 1893

By W. G. Pfann

In zone-melting, a small molten zone or zones traverse a long charge of alloy or impure metal. Consequences of this manner of freezing are examined with impurerespect to solute distribution in the ingot, with particular reference to purification and to prevention of segregation. Results are expressed in terms of the number, size, and direction of travel of the zones, the initial intermsofsolute distribution, and the distribution coefficient. IF a charge of binary solid-solution alloy is melted and then frozen slowly from one end, as for example in the Bridgman method of making single crystals,' coring usually occurs, with a resulting end-to-end variation in concentration. Such coring, or normal segregation, is undesirable where uniformity is an object. On the other hand, for certain systems, it can be utilized to refine a material by concentrating impurities at one end of the ingot.'. ' In the present paper a different manner of freezing will be examined with respect to the distribution of solute in the ingot. A number of procedures will be indicated which have in common the traversal of a relatively long charge of solid alloy by a small molten zone. Such methods will be denoted by the general term zone-,melting, while the process described in the preceding paragraph will be called normal freezing. It will be shown that, in contrast to normal freezing, zone-melting affords wide latitude in possible distributions of solute. Segregation can either be almost entirely eliminated or it can be enhanced so as to provide a high degree of sttparation of solute and solvent. A number of simplifying assumptions will be invoked which, while not entirely realizable in practice, nevertheless provide a suitable point of departure for more refined treatments. Moreover, our own experience with zone-melting has shown that, for certain systems at least, the analysis holds quite well. The present paper will be confined to a discussion of principles and a general description of procedures. Comparison with experiment is planned for later publication. Normal Freezing Before considering zone-melting, segregation during normal freezing will be reviewed briefly. If a cylinder of molten binary alloy is made to freeze from one end as in Fig. 1, there usually will be a segregating action which will concentrate the solute in one or the other end of the ingot. If the constitutional diagram for the system is like that of Fig. 2, then the distribution coefficient k, defined as the ratio of the concentration in the solid to that in the liquid at equilibrium, will be less than one and the solute will be concentrated in the last regions to freeze. If the solute raises the freezing point, then k will be greater than one and the solute will be concentrated in the first regions to freeze. The concentration in the solid as a function of g, the fraction which has solidified, can be expressed by the relation: C = kC0 (1-g)k-1 [I] where C, is the initial solute concentration in the melt. Eq 1 is based on the following assumptions: 1—Diffusion in the solid is negligible. 2—Diffusion in the liquid is complete (i.e., concentration in the liquid is uniform). 3—k is constant. Concentration curves representing eq 1 for k's from 0.01 to 5.0 are plotted in Fig. 3. This equation, in one form or another, has been treated by Gulliver,³ Scheuer,4 Hayes and Chipman5 for alloys and by McFee2 for NaCl crystals. It is derived in Appendix I. It should be pointed out that the k which is calculated from the phase diagram will be valid only in the ideal case for which the stated assumptions are correct. In all actual cases, the effective k will be larger than this value for solutes which lower the melting point, smaller for solutes which raise the melting point, and will probably vary during the beginning of the freezing process. For simplification it will be assumed that the ideal k is valid. Zone-Leveling Processes The processes of this part are designed to produce a uniform, or level, distribution of solute in the ingot. Single Pass: Consider a rod or charge of alloy whose cross-section is constant and whose composition, C2, is constant, although permissibly varying on a microscopic scale." Such a charge might be a rapidly frozen casting or a mixture of crushed or powdered constituents. Cause a molten zone of

Jan 1, 1953

By Milton E. Wadsworth, Edward M. Eyring

BETTER understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique1,2 employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra. In applying the pellet technique to solids of large surface area, French and his coworkers3 have surveyed the adsorption of organic flocculants on clay minerals, oleic acid on fluorite, and ammonia on cracking catalysts. Recent work on application of differential infrared spectroscopy to the study of solid surfaces' has demonstrated that the difference between a sample and a reference can be obtained with double-beam instrumentation. In this way displacement of surface products, adsorption of new products, and differences in the substrate, if any, may be detected. Experimental Procedure: Potassium iodide pellets were used in this study, prepared from recrystallized analytical reagent grade KI. Grinding was carried out in a Fisher mechanical agate mortar. Two-gram plates containing the solid under study were pressed in a special evacuated die constructed in the laboratory at the University of Utah." Concentration depended on the solid in question. Zinc sulfide and willemite are sufficiently transpar- ent in the infrared region for concentrations as high as 20 mg of mineral in 2g of KI to be used. Zinc oxide is even more transparent, permitting concentrations as high as 60 mg in a 2-g plate. For non-differential operation, however, much lower concentrations (2 to 10mg/2g KI) had to be used. Spectra were obtained on a Per kin-Elmer 21 double-beam recording infrared spectrophotometer. A sodium chloride prism was used giving a spectral range of approximately 2 to 15 v wave length. For differential runs a resolution of 1000 was used and the scanning speed was controlled commensurate with instrument response. The response was checked continuously and each spectrum was repeated several times. For nondifferential runs a resolution of 927 was used. Zinc oxide used was analytical grade oxide fume. The zinc sulfide was precipitated from solution with analytical grade zinc sulfate and sodium sulfide. The precipitate was washed and centrifuged several times and dried. Before use the precipitate was washed in dilute HCl and then treated with saturated NH4Cl to remove any bulk oxides and sulfates. X-ray patterns of the precipitate were comparable to that of the natural mineral sphalerite. The precipitate was much more satisfactory than finely ground natural ZnS because of its very large surface

Jan 1, 1957

By Adolph Knopf, L. G. Westgate

Pioche lies 240 miles southwest of Salt Lake City, in southeastern Nevada, 19 miles west of the Nevada-Utah line. It is at the end of a branch line (33 miles), which connects at Caliente with the Los Angeles and Salt Lake division of the Union Pacific System. Its commercial relations are with Salt Lake City and Los Angeles, chiefly with the former. The surrounding area is part of the Great Basin, an arid region of alternating mountain range and intermont plain, the latter floored with out-wash from the mountains. About Pioche the plain varies between 4700 and 6000 ft. above sea level. The town lies in a valley at the east base of a low northwest-southeast range (the Pioche Hills) 12 miles in length, which rises about 1000 ft. above the adjacent flat. West of the Pioche Hills is a higher north-south range consisting of two parts: to the south the Highland Range, between Bennett Pass and Stampede Gap; to the north the Bristol Range, from Stampede Gap to Bristol Pass. This double range reaches altitudes of 8000 to 9000 ft., or more (the highest point, Highland Peak, is 9395 ft.), and rises some 2500 ft. above the surrounding plain It is continued in lower hills to north and south. Smaller ranges rise from the flat west of the Highland and Bristol ranges. The area studied and shown on the map (Fig. 1) is covered by three inch-to-the-mile topographic sheets: the Highland Range, the Bristol Range, and the Panaca, the latter mapped in part only. The sedimentary rocks of the district include Paleozoic limestones, sandstones and shales, Pliocene tuffs, and modern wash. Igneous rocks are represented by intrusive dikes and stocks and by extensive lava flows of mid-Tertiary time.

Jan 1, 1927

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product and the Hanna Mining Co.'s Groveland plant on the Upper Peninsula of Michigan is no exception. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper and various iron silicates.1 Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals.2 Flotation of the spiral tailings makes up about 75% of the concentrate, while a minor amount of concentrate (less than 3%) is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tpy. The initial concentrating facilities were constructed in 1958 and the concentrate was marketed as sinter feed until a pelletizing plant was added early in 1963. Grade improvement soon became a high priority research project, and several methods of concentration were investigated.

Jan 3, 1968

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Clifford Wilson

SCREENED pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments a. Consolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use. of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1932

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division Council A W Thornton (ISD), Chairman, R W Shearman, Secretary, C S Barrett (IMD), J C Kinnear, Jr (EMD), John Chipman (ISD), J S Smart, Jr (IMD), A W Schlechten (EMD), M E Volin (MED), D S Eppelsheimer (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, J J Golden,T D Jones, Evan Just, J C Kinnear, Jr, M Tenenbaum Pacific Northwest Regional Conference E R Marble, General Chairman, Marshall Huntting, Assistant General Chairman, W C Douglass, Mining Chairman, H C Hughes, Mining Chairman for British Columbia, W C Douglass, Mining Chair¬man for United States, Paul Billingsley, Geology Chairman, W D Nesbeitt, Miner¬als Beneficiation Chairman, H D Kelley, Industrial Minerals Chairman, J G Johnston, Metals Chairman, Lloyd Banning, Iron and Steel Chairman, W G Rouillard, Extractive Metallurgy Chairman, E C Roberts, Physical Metallurgy Chairman, D A Pifer, Mineral Industry Education Chairman, Frederick Brien, General Arrangements Chairman Metals Branch Membership Committee C M Squarcy, Chairman, R C Cole, Harold Mar¬golin, M E Nickel, S K Scovil Bylaws Committee A W Thornton, Chairman, W R Hibbard, Jr, J S Smart, Jr (IMD), John Chipman, T S Washburn (ISD), T D Jones, J D Sullivan (EMD)

Jan 1, 1956

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally.' Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan,3 show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision; using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by, the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.5 However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: [3fB = 9.20•'./V•Vn- (n-1) • (n+2) /8[1]] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts' as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of, a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsymmetric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat I than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system, of one degree of freedom can be applied: [1E/m[2] fP = 27] Here f, is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: [t~ = 2/f = 7r\/m/E[3]] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson' 1831) [aP = 4 D2.pL•g•h +7rD•y sin a[4]] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, pL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of-the liquid in cm, y the surface tension in dynes per cm and a the supporting angle' or the one required to insure equilibrium, a being smaller than the contact angle ?. Although demonstrated by Poisson, it has not

Jan 1, 1952