Search Documents

By Wm Price

THE object of this paper is to present a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350° C. throughout the commercial annealing range. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: ALLOY COPPER, LEAD, IRON, NICKEL, MANGANESE, ZINC, PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. PER CENT A 64.68 Trace 0.194 - 6.73 0.06 remainder B 65.82 1.27 0.227 6.17 0.06 remainder C 65.44 Trace 0.345 17.83 0.08 remainder D 65.60 1.08 0.238 17.77 0.06 remainder These alloys were rolled in accordance with regular mill practice to approximately No. 6 B. & S. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately .one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 ½ in. long by ;Z in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 2 1/2 in. were also taken.

Jan 10, 1920

By R. G. Ward, John Henderson. R. G. Hudson, G. Derge

Densities of melts of the iron oxide-silica system in contact with solid iron have been measured by the maximum hubble pressure method in the composition range O to 37 wt pct SiOz and the temperature range 1255 to 1410C. The constitution of the melts is discussed and it is postulated that the structure changes from a dislribution of iron ions in an oxygen ion network at pure "FeO" to a distribution. of iron ions in a network of silicate tetrahedra at the orthosilicate composition. JOHN HENDERSON, Junior Member AIME, was formerly with the Metals Research Loborotory, Carnegie Institute of Technology, Pittsburgh, Pa., on leave from Broken Hill Proprietary Co., Ltd., Research Division, Shortland, Australia. R. G. HUDSON, formerly with Metals Research Laboratory, is now with the John Jay Hopkins Loborotory for Pure and Applied Science, General Atomic Division, General Dynamics Corp., LaJolla, Calif. R. G. WARD, was formerly with the Department of Metal lurgical Engineering, Carnegie lnstitute of Technology, while on leave from the Department of Metallurgy, University of Sheffield, England. G. DERGE, Member AIME, is Jones and Laughlin Professor of Metallurgical Engineering, Carnegie lnstitute of Technology. Manuscript submitted January 19, 1961. ISD The system iron oxide-silica is an important one metallurgically because it forms the basis of several complex slag systems in use for industrial smelting and refining processes. In recent years considerable work has been done on liquids of this system but there are still many points of difference among workers using different experimental techniques and theoretical approaches. Phase equilibria/"3 activity,4-6 electrical conductivity,' current efficiency,' transference number,8 viscosity,9 surface tension,'' and density" measurements have all contributed to an understanding of the problem. Measurement of density is one procedure which is directly indicative of liquid structure since any deviation from ideality must be a result of structural interactions. Liquids of the iron oxide-silica system are of special interest because this is one of the few metal oxide-silica systems on which measurements can be carried out conveniently over the entire composition range from pure oxide to silica saturation. This includes the range of high basicity which has received relatively little attention in other systems. Although one investigation of density in this system has previously been undertaken," the results seem of sufficient importance to warrant the independent redeter-mination reported here.

Jan 1, 1962

By T. Cameron Kenney

INTRODUCTION Whereas the design of rock slopes in open-pit mines is done largely by mining engineers and geologists, the design of slopes in overburden at this point in time is a problem for which civil engineers or geotechnical engineers are best prepared to deal. The reasons for this situation are to be found in the educational curricula and the technical journals of the two groups, where soil mechanics has received little attention by mining engineers and geologists, and rock mechanics has similarly received little attention by civil engineers. In ten years' time this paper will hopefully be considered by young mining engineers to be a repeat of the material that they studied at university. However, even in ten years time I believe that the civil (or geotechnical) engineers will be extensively used as consultants on overburden- slope problems of open pit mines because mining companies will find this more expedient than maintaining their own geotechnical staff, special field equipment and special testing laboratories. For this reason, the purpose of this paper is not to condense several university soil mechanics courses into a twenty-page text for mining engineers and geologists. Rather, the purpose of the paper is to offer a general explanation of various factors affecting slope stability so that mining engineers and geologists will have a better understanding of the behaviour of overburden soils in slopes. A great deal has been written in soil mechanics literature on the subject of slope stability. No attempt will be made to reference all this material but rather only a selected number of references will be cited. Excellent general treatments of the subject of stability of overburden slopes are available (1,2,3,4). Further information of a more specialized nature is to be found in such publications as the Journal of the Soil Mechanics and Foundation Division of the American Society of Civil Engineers, Geotechnique (printed by the Institution of Civil Engineers, England), Canadian Geotechnical Journal, and the proceedings of the conferences of the International Society for Soil Mechanics and Foundation Engineering. FACTORS INFLUENCING SLOPE STABILITY There are two general scales of slope-stability problems, gross stability and local stability. Gross stability refers to large volumes of soil, and gross instability would involve large rotational-type shear failures. Local stability refers to something much smaller and examples

Jan 1, 1972

By T. N. McVay, E. E. Creitz

Rather large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about I. miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and ti-tanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, Opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The x ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fe+2 and Fe+3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1949

By O. G. Bell

While all of the Southwest Texas fields lie within the Gulf Coastal Plain this area may be divided into three subdivisions—the Coastal Plain zone proper, the Reynosa Escarpment zone, and the interior zone. The Coastal zone includes that strip adjacent to the Gulf of Mexico and . extending inland for a distance of about 60 miles and includes the Palo Blanco, Palangana, Piedras Pintas, Kingsville, Agua Dulce, Saxet, White Point and Refugio fields. The Reynosa Escarpment zone includes a Pliocene overlap over older Tertiary sediments lying west of the Coastal zone. The western margin of the Reynosa formation forms a more or less well-defined westward facing escarpment with which the so-called Reynosa Escarpment fields are indirectly related. These fields include those in eastern Zapata, eastern Webb, western Jim Hogg, western Duval, McMullen, Live Oak, Bee, Goliad and Victoria counties. The interior zone includes these fields west of the Reynosa Escarpment which are not in any way related to it and are on separate types of structure. Production data by fields and wells are shown in Table 1. Roma.—During 1928 the Texas Co. completed two small gas wells at 198 ft. on the Roma Structure near the town of Roma on the Rio Grande in Starr County. This gas is of no commercial importance but was used for fuel in drilling other deep tests on this structure. Three dry holes ranging from 3600 to 4200 ft. were drilled; then their No. 4 Guerra, the fourth deep test, was completed during December as a small producer of 37" Bé. oil from a sand at 3560 to 3590 ft. No production was marketed during December but arrangements were being made to handle the output from this well during 1930. This is the first commercial producer in Starr County. Driscoll.—In 1929, Robert Driscoll discovered gas on his Santa Rosalia Ranch in Duval County while drilling water wells. Two sands were developed, one at 2400 ft. and another at 2936 ft. and several gas wells were completed in each, ranging in volume from 15,000,000 to 40,000,000 cu. ft. and in reservoir pressure from 500 to 1,000 Ib. Early in January of 1929, Mr. Driscoll's No. 14 Fee was completed as a 50-bbl. oil producer at 2894 ft. Two other oil producers were completed early in 1929. Mr. Driscoll's death early in the year curtailed develop-

Jan 1, 1930

By Norman D. Fitzgerald

The purpose of this paper is to analyze the behavior of oil securities during the six-year period January 1932 through December 1937. This period was selected because of its varied character. It includes the depths of the depression, the broad and spasmodic recovery, and the recession collapse. The first part of the analysis is devoted to the correlation of a number of economic factors with an index of 13 oil stocks. The second part is a comparison of the different,ial behavior of 6 oil stocks. The relationships developed here are only a few of many that might be considered in a complete analysis. The stock market is regarded as a barometer of business confidence and as such exerts an important influence upon corporate policies, particularly upon industrial expansion. The complex and continuously changing nature of its price structure, the ebb and flow of influences and the effects of impacts require dynamic rather than static analysis. When treated in this way, many of the important fluctuations in market prices and changes in the relationships between securities appear quite logical. The market for oil securities has varied widely in recent years. The Standard Statistics index of 13 oil stocks made a bull market peak of 166.7 in September 1929. The collapse of the boom and the ensuing bear market finally carried the index down to a low of 36.4 in June 1932. From this point oil stocks made an irregular recovery; they reached a top at 139.7 in March 1937, and after maintaining this approximate level through August, declined precipitously to 93.3 in December 1937. The prices of these 13 oil stocks have gone up and down under the influence of numberless variables. These variables are of two kinds, those external to the industry, and those that are solely due to its internal condition. The external factors are political, social, and economic, both domestic and foreign. These are the influences that induce the ebb and flow of all prices in general and security prices in particular. Among the internal factors are the regulation of industry, the development of new reserves and processes, and the disequilibrium due to lack of balance between supply and demand. Some of the simpler relationships are examined in this paper.

Jan 1, 1938

By T. N. McVay, E. E. Creitz

INTRODUCTION Object RATHER large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about 10 miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment Station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and titanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The X ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fee and Fe3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1947

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood's point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood's point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915

By W. J. Reagan

THE problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity-to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 coax.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot-after coming from the slicing lathe. Just sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By Frank A. Wardlaw

My subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanida-tion plant. During the process of development, sulfide ore was found assaying about 5 per cent. copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direet-smelting lead ore was also mined. In 1918 and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation concentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. Results of Selective Flotation In 1924 the mine was on the point of a shutadown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the International Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

The following is an incomplete list of members and guests who called at Institute headquarters during the period Oct. 10, 1919, to Nov. 10,1919. Carl A. Allen, Salt Lake City, Utah. W. G. Mitchell, Montreal, Canada. M. M. Altmayer, Paris. Henry S. Munroe, Litchfield, Conn. A. E. Bellis, Major Ord., Springfield J. S. Negru, New York, N. Y. Armory, Springfield, Mass. Edmund Newton, New York, N. Y. R. S. Botsford, New York, N. Y. A. W. Newberry, Cleveland, Ohio. Henry S. Burnholz, Monterrey, Mexico. C. C. O'Harra, Rapid City, S. D. D. E. A. Charlton, New York, N. Y. Fred S. Porter, Philadelphia, Pa. C. C. Colburn, Denver, Colo. Donald A. Powell, Columbus, Ohio. C. V. Corless, Coniston, Ontario. Thomas T. Read, Washington, D. C. I. N. Daily, Seattle, Wash., W. L. Remick, Chrome, N. J. E. V. Daveler, Butte, Mont: Hallet R. Robbins, San Francisco, Calif. John Davis, Fairbanks, Alaska.' Milnor Roberts, University Station, E. W. Engelmann, Salt Lake City, Utah. Seattle, Wash. M. E. Erdofy, New York N. Y. Thos. S. Roberts, Lakehurst Proving W. F. Ferrier, Toronto, Canada. Grounds, N. J. H. A. Fisher, Pittsburgh, Pa. George B. Rodgers, Dobbs Ferry, N. Y. Walter Fitch, Sr., Eureka, Utah. John C. Rogers, Copper Cliff, Ontario. C. D. Grier, New York, N. Y. Joseph L. Rosenmiller, Bethlehem, Pa. A. Hibbert, London. . C. J. Saville, Portland, New South Wales. John E. Hodge, Minneapolis, Minn. W. A. Scheuch, New Jersey. W. E. Hopper, Newark, N. J. S. B. Shutts, Lynchburg, Va. M. R. Hull, McGill, Nev. E. W. Smith, U. S. Army. A. W. Ibbett, Trinidad, B. W. I. S. J. Speak, London. A. O. Ihlseng, Joplin, Mo. John. B. Stewart, Santiago de Cuba, Sherwin F. Kelly, Lawrence, Kans. Cuba. R. G. Knickerbocker, Logansport, Ind. S. A. Taylor, Pittsburgh, Pa. .M. H. Kuryla, Eureka Colo. Karl Thomas,' New York, N. Y. F. G. Lasier, Detroit, Mich. F. L. Torres, Eureka, Nev. David Lasuer, Elizabeth, N. J. Henry Traphagen, Toledo, .Ohio: H. H. Lauer, Allentown, Pa. W. D. Van Doren, Ottawa, Canada. J. Whitney Lewis, Care First Nat'l Bank, J. A. Vernon, Newport, R. I. Tulsa Okla James Wilding, San Francisco, Calif. James W. Love, Knoxville, Tenn. D. J. Williams, Butte, Mont. Dorsey A. Lyon, Washington, D. C. Harry J. Wolf, New York, N. Y. M. E. Martiner, Boston, Mass.. Dwight E. Woodbridge, Duluth, Minn. Benj. L. Miller, Bethlehem, Pa. Percy E. Wrighn, Seattle, Wash. W. G. Miller, Toronto, Canada. F. Yamada, Tokyo, Japan.

Jan 12, 1919

By ANTON GRAY

In considering the possibilities and costs of discovering minerals by exploration. mineral occurrences may be classified roughly according to the size of the target they offer to the various methods that have been used to search them out. This classification is advantageous because the methods of search which might be expected to give results in one case may be totally inapplicable in others. Mineral deposits for the most part have been found in groups, or districts, in which the individual deposits occur under the same general geological conditions and usually contain more or less the same metals. There are, also, what are apparently isolated de- posits, although if the truth were fully known many of these probably would not be isolated. These districts, such as the Belgian Congo copper fields, the California Mother Lode, and the Linares lead district of Spain, form the first division of my classification. The second division is formed of the individual deposits of these districts, for example, Kambove mine in the Congo, the Kennedy-Argonaut vein in California, and the Cruz vein at Linares. The third division consists of the separate ore bodies that make up the deposits

Jan 1, 1949

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. PURPOSE Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls

Jan 1, 1946

By R. H. Hopkins, R. W. Kraft

X-ray and metallographic analysis reveal that the preferred cryslallograPhic relationships in direc-tionally solid~fied Pb-Sn eutectic specimens can be stated: interface growth direction, Experiments in which tin single-crystal seeds were used to nucleate the eutectic demonstrate that the normal lamellar structure observed at steady state can be forced to break down initially to a semide-generate structure when the crystallograPhic direction of the tin seed does not lie within the preferred eutectic interface plane. A normal structure eventually develops by preferred grain growth. X-ray topo-graphs and rocking curves substantiate that the perfection of eutectic samples increases as growth proceeds until steady-state conditions prevail. RECENT years have seen substantial progress made in the understanding of eutectic solidification through both intensive theoretical1'' and experimental investigations (see Ref. 7 for a review and extensive bibliography of both aspects). Several important observations concerning the nucleation and growth aspects of binary eutectic solidification have been brought to light. Briefly some of these include the nonrecipro-cal nucleation of one phase upon another,'j9 the tendency for a specific low-index direction of one or both phases of the eutectic to be aligned in the growth direction during unidirectional solidification,'0711 and the production of lamellar microstructures having a preferred interface plane between "11-13 phases. Questions quite naturally arise as to the mechanism by which preferred grain growth evolves during eutectic solidification and what relationships (if any) connect the initial nucleation of one phase upon another with the preferred growth directions and interface planes observed after a few centimeters of growth in many systems. This study was initiated in an attempt to answer these questions. An experiment was devised in which both the nucleation and growth steps in the crystallization of a binary eutectic, Pb-Sn, could be correlated with subsequently developed eutectic morphology and crystallography. This was accomplished by nucleating the eutectic upon a tin single crystal seed and then causing the eutectic to grow from the seed by directional freezing. The morphology of the structures produced in this manner was then monitored metallographically and the orientation relationships and substructural perfection determined by X-ray analysis. The information thus ob- tained was correlated to the growth history of the samples. EXPERIMENTAL DETAILS The eutectic of composition 38.1 wt pct Pb and 61.9 wt pct sn14 was prepared by accurately weighing lead and tin of 99.999+ (from ASARCO and Lytess Metals and Chemicals, respectively), melting in a clean Pyrex beaker under an argon blanket, and casting into the proper crucible for resolidification as described below. Tin seeds were grown by the method of ~halmers," saw-cut, oriented by the Laue method, and soldered to the pull rod of the Czochralski puller. All seeds were given a final electropolishing (to assure the removal of any deformed material from the cutting operation) and acetone degreasing immediately prior to the nucleation experiment in which they were to be used. Eutectic samples were unidirectionally solidified in a horizontal graphite boat1' or by pulling from the melt16 with tin (or graphite) seeds. A flowing argon atmosphere was employed in all experiments and growth rates and temperature gradients, constant for a given run, varied from 2 to 4 cm per hr and 8" to 15°C per cm over the course of all the experi-

Jan 1, 1969

By Burt C. Mariacher

The Minerals Beneficiation Division meets each year at the Annual Meeting of AIME. All members are invited and encouraged to attend. For the information of those who did not attend the meeting in Denver last February, this column presents a summary of the reports given and topics discussed. Technical Committee Coordination Consolidation of technical programs having common interest to MBD and the Extractive Metallurgy Division is proving a considerable success, both on the technical committee level-through the efforts of the MBD-EMD Coordinating Committee-and in special symposia. MBD Chairman, R. S. Shoemaker, noted that J. D. Prater will be serving as Chairman of both the MBD Chemical Processing Committee and the EMD Hydrometallurgy Committee for 1970-71. R. P. Ehrlich commented on the cooperative effort of both divisions in organizing the Copper Metallurgy Symposium held at the Denver Meeting. This effort, he said, was important to the success of the Symposium. H. R. Spedden discussed inter-Division coordination activities on the SME level. The forthcoming MBD-M&E-EMD Joint Lead-Zinc Symposium is yet another example of progress in this direction.

Jan 1, 1970

By G. K. Manning, A. R. Elsea, A. B. Westerman

A considerable number of high-tem-perature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. .4t the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in vitalliurn after various heat treatments. Howcver, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chro-mium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja and Guertler2 indicated that cobalt and chro-mium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to 85 pct chromium undergo a transformation at [zoo to 12 50 c More recently, Wever and Haschimoto,3 Wever andLange,4and Matsunaga5 carried Out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallogra~hic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Mat-SUnaRa. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these excep-tions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data arid the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitalhum by deter-mining the diagram for the cobalt-chro-mi~m system- Experimental Work For the convenience Of the reader, the diagram as determined by the present investigation is presented in Fig 3. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the melting point for pure chromium is the

Jan 1, 1949

By Frank A. Wardlaw

MY subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanidation plant. During the process of development, sulfide ore was found assaying about 5 per cent copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direct-smelting lead ore was also mined. In 1918'and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation Eoncentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. RESULTS OF SELECTIVE FLOTATION In 1924 the mine was on the point of a shutdown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the Inter- national Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

By Tell Ertl

An annual invitational address by an outstanding man in mining, geology, or geophysics who has contributed significantly to the progress of technology in these fields. IN 1954, the first year the award was conferred, Fred Searles, Jr., remarked, "The earlier years are the easiest." In this, the second year, it was easy to choose the outstanding mining engineer. Our conferee this year has been destined to mine. He comes from pioneer stock, and though a son of the American Revolution he is most proud that all four of his grandparents came to the Jordan River Valley of Utah the "first summer," which all Utahns will recognize as 1847. At the time of discovery of high-grade ore in Bingham, his grandfather, Archibald Gardner, had a crew of men getting out saw timber in the area. The first claim staked in Bingham Canyon was named the Jordan, and Bishop Gardner was the colocator of the claim as well as the man to record it. E. D. Gardner was born in West Jordan, Utah, in view of Little Cottonwood Canyon, the site of the Emma Mine. Park City in the Wasatch Mountains a few dozen miles to the east, and Tintic, not much further to the south, were developing their vast ore-bodies throughout his youth. As a boy he was near the present Midvale metallurgical area and could see the Lark and Bingham Canyon mine dumps and imagine the mining activities at Tooele, Ophir, and Mercur just over the nearby Oquirrh Range. He was 11 years old when the first car of copper ore was shipped from Bingham Canyon. It was not surprising that he attended the University of Utah and graduated with an engineer of mines degree. Five years with the Utah Apex in Bingham Canyon as chief engineer and assistant superintendent completed his training for the 44 years of unselfish and lightly rewarded service he was to give the mining industry as a Government engineer. All of us in mining are familiar with the great work he carried on and directed during the genera- tion he supervised the Southwest Experimental Station at Tucson. He has written scores of papers and books. His observations and experiments on drilling and blasting have led to the important improvements in this field during the past quarter century. Whereas those of us who consider ourselves widely informed about underground metal mining methods make hasty trips through a half dozen or dozen mines a year, our conferee has visited them all—not only the metal mines, but also coal and hundreds of nonmetallic mines, in the United States, Canada, Latin America, and overseas. His keen observations and analytical mind have resulted in an encyclopedic knowledge of mining and mines. His improvements in mining technology have been steady and predictable. His elucidation of mining problems to the many young engineers that have come under his guidance have made them grow strong and useful to his industry. When he chooses to stop, his influence will continue to expand and prosper because of the inspiration and dedication he instilled in so many of us. The profits from his ideas have been distributed throughout the mining industry. He has remained a technical man who felt that he could serve the mining industry best as a Government engineer. But he is the staunchest advocate of the belief that the public should gain from his work through private industry. This is not the first recognition E. D. Gardner has received. The Department of the Interior awarded him the coveted Medal for Distinguished Service in October 1949, and he received the Engineering & Mining Journal's Salute in March 1951. His friends who are presenting him the Daniel C. Jackling Award today know this great mining engineer simply as "Ed" Gardner.

Jan 1, 1956