Search Documents

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By Nelson Severinghaus

Crushed stone leads all industrial mineral, except cement in annual value of production in the United States. It is also interesting to note that crushed stone value is exceeded only by that of fuels, cement, and iron ore among all mineral products of this country. An industry which started with hand-sledging to produce smaller sizes of broken stone for hard surfaced improvement of roadways as designed by McAdam in England about 1815 has grown into a complex industrial giant. Most of this growth started with the invention of a mechanical rock crusher just under one hundred years age (1858) by Eli Whitney Blake. This invention made possible the production of greater tonnages of smaller sizes of broken stone and greatly accelerated its use for Macadam road pavements and for railroad ballast. Stones Used for Crushing All three of the major geologic classifications of stone, sedimentary, igneous, and metamorphic, are widely used in the production of crushed stone. Satisfactory physical and chemical properties can be found in each type so that economic availability becomes the prime determinant for development. Table 1 lists more common rocks of the three main groups with average values of specific gravity and toughness as measured by Deval test. This widely used classification was suggested by C. E. Lord, of U. S. Bureau of Public Roads. The physical properties were compiled by D. O. Woolf in "The Results of Physical Tests of Road Building Rock," U. S. Department of Agriculture, Bulletin 76. It should be noted that the figures given in Table 1 are averages. Very substantial variations in the physical properties of rocks within any one classification will occur. The solid surface of the earth was first made up of igneous rocks resulting from the solidification or crystallization of molten material upon cooling. These igneous rocks were disintegrated into sand, clay, and gravel by the weathering action of wind, water, chemicals, [ ] and temperature changes. The products of weathering were transported by wind and streams until they reached less turbulent areas such as oceans or lakes and were deposited. Chemical deposition between grains of sand or clay or the physical action of pressure and heat then solidified them into sedimentary rocks

Jan 1, 1960

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By Frank H. Kneeland

Safety First is a popular motto—most mining companies have adopted it. It is probable, however, that in the majority of cases it is only a motto and gets no further than the office stationery or the bulletin board at the mine's entrance. In but few industries is there employed a greater diversity of machinery and mechanical devices than in coal mining. The list ranges all the tray from mechanical stokers to wood-working machinery and undercutters. Many of these devices, particularly those employed in wood working, are extremely dangerous. In 1913,23 per cent. of all fatalities occurring in coal mining in the U. S. were caused by machinery of some sort or other. Although the forms of accidents occurring with mining machinery are legion, they generally arise from one or more of five causes: (a) Falls from ladders, platforms, etc.; (b) coming in contact with moving machines or parts thereof; (c) electric shocks; (d) failure of some machine part; (e) mismanipulation of valves, levers, switches or other hand-operated controlling devices. The steps which may be taken to prevent accidents from the above causes are almost as numerous as the accidents themselves. There is, and can be, no panacea for all mishaps, nor for any one class of accidents. There is no mathematical or other formula that will bring immunity under any set of conditions. Common sense is the only guide. The remedy for the first-named class of accidents is simple and generally effective—namely, make the staging, ladder, platform, or other support, abundantly strong to carry any possible weight that it may be called upon to bear; provide ample railings on platforms or runways, and non-slipping feet on movable ladders. Coming in contact with moving machine parts is one of the greatest dangers met with in the operation and maintenance of mining machinery. Unfortunately, machine manufacturers have not as a class adopted the idea of thoroughly protecting and incasing the dangerous parts of their product. No one has, or should have, a better or more thorough knowledge of what the dangerous parts or elements of a machine may be than its builder. The desire to construct a piece of mechanism as cheaply as

Jan 1, 1915

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

By AIME AIME

MORE than thirty members of the Coal Division attended the Coal Land Valuations Round Table on Monday morning. Chairman Dilworth stated that the Committee had been appointed to take up the question and, after reading the list of members of the Committee, pointed out that the object of the meeting was to formulate a plan of action rather than to discuss any phases of valuation, per se. To this end he presented a tentative outline of points to be considered in the future by the Committee. After a lively discussion on the desirability of inclusion of some questions in the agenda of the Committee, the following outline was adopted :

Jan 1, 1931

With one shaft almost completed and another shaft being sunk, the scope of the Saskatchewan potash area is beginning to come into focus. Some 18 companies have reportedly leased more than four million acres to explore potash possibilities. PCA, farthest along, is located about 15 miles southeast of Saskatoon, and IMC has its project underway near Esterhazy in the eastern edge of the province. U. S. Borax and Chemical Corp. is also reported exploring the area. The field lies in the middle Devonian geological formation which was probed by oil companies along the 200-mile area across the province. Extensive examination began after World War II and deep drilling was started a few years later.

Jan 5, 1958

By P. R. Sperry

A METHOD was recently devised to indicate two or more successive stages of the migration of grain boundaries in aluminum, and to record the direction of the migration. This technique was used for the study of the various types of boundary migration occurring in high purity aluminum.' The method employs alternate annealing and electrolytic etching treatments, repeated as many times as desired. All successive sets of grain boun- dary positions revealed by the various etches appear superimposed on each other. The last etch is designed to leave an oxide film on the surface which is optically anisotropic. The orientation of the oxide film at each point is determined by the orientation of the underlying aluminum grain. When viewed with polarized light using crossed nicols and a Biot-Klein quartz plate, grains with differing orientations appear in different colors, as described by Hone and Pearson.' The last boundary positions are revealed by these color differences. The first step of the process is to obtain a desired starting grain size by annealing, for example, if high

Jan 1, 1951

By Leroy A. Palmer

All the domestic production of magnesite during 1925 came from two states, California and Washington. Of a total of 120,660 tons of crude ore, 64,600 tons, or 54 per cent., were produced in California.' Of this quantity California produced about 99 per cent. of the caustic calcined, but only 10 per cent. of the dead-burned. The largest producer was C. S. Maltby, of San Francisco, who operated the Red Mountain mine, in Santa Clara County, and the Sampson mine, in San Benito County, under lease. These two mines have been studied by the author, and offer interesting comparisons as to mining and treatment methods and final products. Geology The general geology of the magnesite deposits of California has been described by Hess,2 Bain3 and others4 and although a detailed discussion is not necessary here, a brief summary will assist in understanding mining conditions. California magnesite, when comparatively pure, is usually a white, fine-grained rock, with a conchoidal fracture, occurring in veins and lense-like masses in serpentine. The veins vary considerably in width, and usually occur in a series of more or less parallel veins intersected by other series or systems of veins, probably following original or secondary fissures in the enclosing serpentine. The most generally accepted theory of origin is that the magnesite was formed by the action of surface waters charged with CO2 percolating downward through fissures and changing the magnesium silicates of the serpentine into magnesium carbonate.

Jan 1, 1927

A-Metal Mining B-Minerals Beneficiation F-Coal H-Industrial Minerals

Jan 11, 1950

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By J. C. Reed

CINNABAR was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigel1 by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County-across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done con-siderable exploration work and has retorted the high-grade ore so .obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district.

Jan 1, 1935

By C. L. Rabe

The Muddy and Dakota sands, more commonly known as the "D" and "J" sands, respectively, of the Denver-Julesburg Basin are correlative over a large area. It is reasonable to believe, therefore, that depositional environment throughout the Basin was comparable. Local variations in sand development do occur, however, and productivity is often governed by permeability as well as structural position. Experience indicates permeability is commonly a function of cementing material. While cases of siliceous or calcareous cementing have been observed, the bonding material is, for the most part, clay. Under the latter circumstance, clay should bear some relation to permeability. Similarly, gamma radiation should bear some relation to the amount of clay. This study was undertaken to determine if a cross relation exists between gamma radiation and permeability. RESULTS OF INVESTIGATION A qualitative relation does exist between gamma radiation and permeability for clay-bonded Muddy and Dakota sands of the Denver-Julesburg Basin. This is illustrated graphically by Fig. 1, which shows corrected gamma ray deflection vs permeability for five wells over an area approximately 50 miles long and 8 miles wide. The "corrected" gamma ray deflection cannot be read directly from the gamma ray survey in all cases. It became apparent early in the investigation that methods would have to be developed for converting all gamma ray surveys to a common deflection scale and to correct for thin bed effects. COMMON SCALE DEFLECTION Because all logs are not recorded in the same calibration units or at the same sensitivity, it was felt they could be most readily converted to a common scale by measurement of deflection in inches from zero. Initially, four wells in the Jacinto field of Nebraska were carefully correlated, and selected intervals were planimetered to obtain average deflections. Average deflections of planimetered intervals from three of the wells were plotted vs those of the fourth well which was to be used as a common reference. The plots are shown in Fig. 2. While results obtained by this method in the Jacinto field were relatively good, the planimetered intervals were not easily correlated with logs from other fields. Furthermore, the planimetric method is laborious and not readily adapted to routine operations. Deflection of the "Bentonite marker" was found to

Jan 1, 1958

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By L. W. McKeehan, W. C. Elmore

THE magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter' first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel' single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. SPECIMENS The following list describes the specimens used in the present investigation. DESIGNATION DESCRIPTION A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which he gave the following typical analysis: C, 0.05; P, 0.038; 5, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick.

Jan 1, 1935

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions' it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1939 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and ;I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron. and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which is issued quarterly. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administra-tion, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CON-TRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes. CONTRIBUTIONS and Other TECHNICAL PUBLICATIONS will be sent upon request. A member relay purchase an additional copy of a TECHNICAL PUBLICATION Or a CONTRIBUTION at One cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION Of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum; Canadian and foreign postage 50 cents extra. METALS TECHNOLOGY, $7 per annum; Canadian and foreign postage 50 cents extra (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum; Canadian and foreign postage 50 cents extra (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers). PETROLEUM TECHNOLOGY, $4 per annum; Canadian and foreign postage 50 cents extra. Bound volumes have been mailed to members that have requested them, and MINING AND METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and lie may purchase for $2.50 one copy of a volume not already received; additional copies of 'the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members; to nonmembers 50¢ current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum plus $1 for Canadian or foreign postage.

Jan 1, 1939

By AIME AIME

Further details of the 97th meeting of the Institute, at Spokane, have been sent to members in the Special Circular of May 8, 1909, and for convenience a summary of the additional information is given later in this announcement. In spite of the present small number who have joined the party, final arrangements have been made to complete the itinerary given in the circular. It is greatly to be desired, both in behalf of the Institute and in recognition of the special courtesies to be extended on the trip, that the party be made larger. Exceptional facilities to visit the many mines and smelters have been freely provided; and members are requested to make all reasonable effort to attend the meeting at Spokane and participate in the excursions. . For those who cannot take the entire trip, it may be possible to provide special Pullman accommodations after leaving the Yellowstone Park. In order to make the necessary arrangements, however, the names of members and guests contemplating this partial trip should be sent at once to Mr. Theodore Dwight, .39 West 39th St., New York, N. Y. A special train of Pullman cars will leave Chicago September 16. This train will be side-tracked at all places visited, and the sleepers will be available for lodging and the dining-car for meals (luring the entire trip, except while taking the tour through the Yellowstone Park. The general cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from Chicago back to Chicago, almost 6,000 miles, and the tour through Yellowstone Park, occupying in all about 30 days. Special accommodations on the train will be furnished at the following rates

Aug 1, 1909

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966