Search Documents

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By Ronald C. Koo

SMALL additions of potassium, aluminum, and silicon as oxides (referred to as dope) to tungsten have been known for several decades to have a very large effect in raising the recrystallization temperature and altering the recrystallized grain morphology of heavily drawn wire. Previous investigations of this doping effect1 6 have led to various speculations but all failed to deduce unequivocally the physical state or the mechanistic influence of the dopant. Recently, walter7 has observed, by transmission electron microscopy, strings of "fine particles" in heavily rolled and annealed doped tungsten sheet and concluded that they were particles of mullite (Al6Si2013). His conclusion was inferred from the electron diffraction patterns of large particles ex-trated by carbon replication of fractured surfaces of slabs rolled from sintered ingots. That the strings of "fine particles" in heavily rolled and annealed sheet were also mullite was an assumption for which no evidence was presented. A similar investigation has been carried out in this laboratory over the past 2 years on a variety of tungsten wire: doped tungsten, and undoped tungsten, as well as 218 doped tungsten purchased from the Lamp Metals and Components Department of the G.E. Lamp Division. Although the electron microscope observations are similar to those reported by Walter, the writer has reached a different conclusion concerning the physical state of the dopant in annealed tungsten. The purpose of this communication is to present evidence that the strings of "fine particles" observed in transmission specimens are not mullite, but are voids. In the present investigation, tungsten wire, 0.88 mm in diam, was rolled into ribbon 0.2 mm by 125 µ thick. The ribbons were annealed in vacuo at a pressure of -1 x 10-5 Torr and then thinned electrolytically in a 2 pct KOH solution. Fig. 1 shows a typical transmissicjn electron micrograph of a sample annealed at 1700°C for 30 min which reveals rows of closely spaced voids having a light contrast (referred to as "fine particles" by Walter) aligned parallel to the working direction. Stereo micrographs (by D. Moon, Westinghouse Research and Development Center) have shown that these voids do not exist on the surfaces of the specimens as a result of thinning but are within the thin-foil specimens. The following experiments have been performed to verify that these are indeed voids. I) Effect of Annealing. Voids are absent in unannealed specimens and appear only after annealing. This behavior cannot be explained if they were solid particles such as mullite. Precipitation (in an unquenched specimen) upon annealing requires solute elements having decreasing solubilities with increasing temperature. Although the solubility of aluminum in tungsten does decrease with increasing temperature, precipitation requires a concentration in excess of 1.4 wt pct,8 which is at least two orders of magnitude higher than the aluminum content in doped tungsten. It is also unreasonable to assume that particles aligned in rows initially present in unannealed specimens were too

Jan 1, 1968

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By Ronald J. Roman

Research pertaining to flow of solutions in leach dumps has generally been neglected. This technical note proposes a method for evaluating the flow patterns and incorporating the results into dump-leaching models. Three dump-leaching models1-3 have been proposed to scale up laboratory test data to expected field results. These models are based on the same physical picture in a dump and differ only in the importance of diffusion or surface chemical reaction rate. Selection of this rate-controlling phenomemon is based on type of ore (sulfide or oxide), physical dimensions of the particles being leached, and the leach heap itself. All three models are applicable to specific types of operations. The models are similar in the use of a size distribution analysis for the dump material and the assumption that the leach solution flows around each particle. Transport of the leaching agent to the interior of the particle takes place by diffusion [(Fig. 1)]. However, normal dumps are of a higher bulk density than the material in a laboratory column used to generate the scale up data. How does this difference in bulk density affect the scale up equations? Increasing the bulk density can be expected to give more particle-to-particle contact; therefore, individual particles will be blinded by each other. As blinding increases with bulk density increase, the particles will behave like larger particles with a coarser apparent size distribution. The extreme will occur when the bulk density reaches that of the undisturbed rock, the entire dump behaving as a single particle with the dimensions of the heap itself. Harris4 alluded to this phenomenon in his paper. An alternative method of describing the same phenomemon is to consider the flow paths of the solution. At high bulk densities leach solution no longer surrounds each particle, but flow paths are separated by several particles and channeling is said to take place. Instead of the particle radius being the maximum distance through which the leaching agent must diffuse, the maximum distance is half the separation distance of the solution flow path. Particle size distribution must then be replaced in the models by the concept of channel separation distribution. Like size distribution, channel separation distribution specifies the cumulative percentage of the rock in the dump situated less than a specified distance from a solution channel. Thus, [ ] Distribution of the solution channels is a function of how the dump was built (among other things), and therefore it cannot be determined in the laboratory. Accordingly, it becomes necessary to determine a range for d and a in existing operations or measuring these parameters before leaching starts. Howard5 gives a clue to one possible technique of measuring solution channel distributions. When his paper was published little was known about the phenomemon of leaching; the importance of this type of data was not recognized. [Fig. 2] is a Y-Y log for one hole drilled

Jan 1, 1978

By AIME AIME

ASIDE from the annual dinner-dance, the two outstanding social events of the Annual Meeting were the dinner- smoker on Monday night and the informal dance on Tuesday night, both of which were held at the Commodore Hotel. Approximately 400 attended the former event, compared with 570 a year ago, and about 250, people were attracted to the dance.

Jan 1, 1933

By AIME AIME

INSTITUTE members attending the Annual Meeting in New York who want to see one of the mining engineers' newest aids, photoelastic stress analysis, are due for an interesting afternoon on Thursday, Feb. 15, when open house: will be held at the Columbia University mining laboratory. Information as to the direction and distribution off stresses in mine structures, which has been developed by Professor Bucky, associate professor at the Columbia School of Mines, and David Sinclair, research assistant, is useful in the design of pillars and in the placing of openings relative to working places such as gangways and haulage levels.: This work has been sponsored during the last ten years by the Engineering Foundation.. It is fully reported in T. P. No. 1140.

Jan 1, 1940

By Claude Ferquson

MORE men are killed and injured in the metal mines of the United States from falls of rock and ore than from any other cause. Dan Harrington, of the U. S. Bureau of Mines, recently stated that "falls of men and material continue to take about 50 per cent of the lives annually lost in our mines (coal or metal) and this kind of accident is now and has been one of the most difficult to prevent." The fact that comparatively little has recently been written on this important subject for the benefit of the metal miner is the incentive for the present paper. Little will be said that will be new, but I hope to place fresh emphasis on certain well-known' principles' and to reiterate and stress previously stated rules so that the average experienced miner, as well as his buddy who may not be so experienced,' will sit up and take notice. It is not within the scope of this paper to discuss mining methods from the standpoint of safety and the prevention of accidents from falls of rock. It is up to the mine management to select the system of mining best suited to the character of the ore deposit and its wall conditions. This is something that the miner can do little about; although in many mines the management encourages the workmen to make suggestions that will improve existing

Jan 1, 1938

By David W. James

DURING a recent investigation of the transition from a planar to a nonplanar solid/liquid interface for the systems H20-NH4F and 0-AIR,' an apparatus was developed which enabled the morphology of the ice-water interface to be examined during the transition. The slightly curved interface was viewed at a glancing angle with a Bausch and Lomb X30 stereomicro-scope. The interface was obliquely illuminated by a polarized light source. It was thus possible to differentiate between small projections or depressions at the interface, both by a shadowing effect and by the way in which they distorted the colored interference fringes across a particular crystal surface. Many attempts were made to photograph the various stages of interface breakdown. Unfortunately, the limited depth of focus of the microscope rendered the system unsuitable for photographic recording. Visual examination, however, was facilitated by continuous adjustment of the microscope focus control. The following observations of the interface transition were recorded for dilute solutions of ammonium fluoride in water. They are compared with iller's postulated morphologies shown in Fig. 1. i) The initial departure from planarity was characterized by the appearance of a large number of small depressions or "pores" in the interface. ii) The pores were arranged in wavy rows all lying roughly in the same direction within a particular grain. iii) The pores did not appear to form near to grain boundaries. iv) The pores appeared in certain grains before others. v) The transition from the pore structure to the elongated cell structure, Fig. l(d), was difficult to follow. It occurred quite rapidly and no truly irregular cell structure, Fig. l(c), was noticed. vi) The elongated cells gradually became more uniform in size and shape, with straight cell boundaries. They remained elongated, however, and no regular hexagonal cells were observed, cf. Fig. l(e). Several conclusions may be drawn from these observations. Firstly, the appearance of a poxed or, more accurately, a pore structure can be used as a criterion for the onset of constitutional supercooling. Care should, of course, be taken to distinguish between the true pore structure and artifacts caused by splashed-back liquid, particles of oxide, or inefficient decantation of liquid retained between cell boundaries, as described by Spittle et al? Secondly, and contrary to the suggestions of Tiller el l., it seems that interfacial perturbations are characterized not by curved projections but by small depressions or pores. A recent independent investigation by Biloni, Bolling, and cole5 reported in this issue indicates that the depressions might be explained in terms of dislocations intersecting the solid/liquid interface. It is possible that the dislocation concentration is reduced in the vicinity of grain boundaries. This would then explain the grain boundary depleted areas noted in (iii) above. This work was partially supported by the Air Force Office of Scientific Research, Contract No. AF 49-(638)-1029.

Jan 1, 1967

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

By W. C. Leslie

W. C. Leslie (Edgar C. Bain Laboratory for Funda mental Research)—This investigation, with its com bination of high-purity metal, calorimetry, and metallography, will serve as a model for annealing studies for a long time to come. The evidence for a competition between recovery and recrystalliza-tion is particularly convincing. The demonstration of edge-nucleated recrystallization was so clear that it may obscure the necessity for other types of "nucleation" sites; otherwise, single crystals of aluminum could not be recrystallized after cold work. At least three types of sites have been found to operate in iron: 1) high-angle boundaries, probably in the same manner as in aluminum, 2) matrix sites, 3) inclusions or second-phase particles. In each instance, the cells developed during cold work and perfected during recovery are the "nucle for recrystallization. Observations by ourselves and others of the dislocation structure of cold-worked metals and of the structural changes that occur during annealing have led us to doubt the validity of the basic assumption of the Lucke-Detert theory, and of the modification developed by Gordon and Vandermeer, that during recrystallization of a metal containing foreign elements in solid solution a high-angle boundary is ad vancing into a cold-worked matrix having a random distribution of solute atoms. We contend that an es sential part of the cold-working and annealing of solid solution alloys is the trapping of solute atoms by the low-energy "wells" afforded by individual dislocations and by dislocation arrays. If cells are formed during cold work, the cell walls are stabilized by this concentration of solute atoms. Thus, solutes inhibit recrystallization not only by decreas-ing the rate of high-angle boundary migration, but also by preventing the formation of high-angle boundaries by subgrain growth or coalescence, i.e., solutes can inhibit both "nucleation" and growth. In addition to stabilizing the dislocation Structure, the solute-dislocation interactions may produce clusters of solute atoms which are not as readily assimilated into the recrystallized grains as are individual solute atoms. There is an additional complication. The dislocation structure formed upon cold working a dilute solid solution may not be the same as that formed during cold working of the pure solvent metal. The solute can either enhance or minimize the formation of cells during cold working. Both effects have been observed in binary alloys of iron. The annealing process is inextricably connected with the mechanisms of strain hardening and solid solution hardening. Although the correlation between experimental boundary migration rates and the predictions made from the theoretical equations are impressive, it should be mentioned that in at least four other instances (Pb-Ag and pb-Au,15, Fe-Mn,16, Fe-Mo)17 the agreement was rather poor. In brief, while it is probable that the migration of high-angle boundaries is held back by solutes in the manner described, this is only a partial explanation of the total effect of solutes upon recrystallization of cold-worked alloys. Paul Gordon and R. A. Vandermeer (author's reply)— The authors first wish to thank Dr. Leslie for his compliments of this work. It is perhaps worth pointing out that some of Dr. Leslie's remarks are directed toward subject matter covered in two earlier papers in our work.18,19 We agree with Dr. Leslie's main contention that the exact nature of the metal structure in the vicinity of a boundary should have an effect on the boundary migration. The theory of Lucke and Detert does not take such detail into account, nor does it account for orientation effects on the migration rates. We assume that since our data checks the theory so well, the effects of detailed structure are statistically averaged out by the polycrystalline techniques used just as are the effects of orientation factors.

Jan 1, 1963

By D. M. Boulin, E. S. Greiner

Single crystals of vanadium were bent at 293" and 77°K to a maximum fiber strain of about 1 pct. Analysis of slip line and etch markings of- crystals deformed at either temperature show the slip planes are {112}. The slip directions at 298° and 77°K, deterwined from the asterism axes of rotation of crystals compressed in a {110} direclion, were (111). Etch pits, associated with dislocations, were observed in the plastically deformed vanadium. There was no evidence of mechanical twinning. THIS paper presents results on single crystals of vanadium plastically deformed by bending and compressing at 298° and 77°K. Bcc metals have been observed to slip on {110}, (1121, and (123) planes while the slip direction has invariably been found to be ( 111) 1 Lindley and smallman2 have studied the deformation intension of polycrystalline vanadium between 298° and 20°K and reported that at and above 77°K the deformation is predominantly by slip, but at 20°K the deformation is associated with twinning. Later, Edington and smallman3 found that single crystals of vanadium compressed in a (111) direction at 77°K deformed by twinning on { 112}( 111) systems. Clough and pavlovic4 have reported that mechanical twins were observed in vanadium loaded by impact at 77°, 173°, and 195°K, respectively. PREPARATION OF SINGLE CRYSTALS The vanadium single crystals were made from commercial vanadium reported to contain 0.03 pct C, 0.03 pct 0, 0.02 pct N, 0.0X* pct Ca, 0.0X pct Si, proximately 0.8 cm diam, 4 cm long and were grown in (100) and (110) directions. A crystal for studies of etch pits was gound to have a face parallel to a {l00} plane by the Bond crystal-orienting technique.7 In order to avoid straining, the crystals were placed on the steel mount with a low-melting organic compound (glycol phthalate) before grinding. Crystals for the bending experiments were ground to have the four side faces parallel to ( 100) planes. The crystals were electropolished8 in 10 pct H2So4 using a current density of about 3 amp per sq cm to remove the strained surface material. The crystals were bent slowly by three-point loading in a stainless-steel jig designed by Sylwestrowicz.9 The end rollers of the jig were 3.8 cm apart. DEFORMATION AT 298°K The bent vanadium crystal, after removal from the jig, had a radius of curvature of 20.4 cm over the 2-cm length close to the center loading roller, where the maximum bending moment occurred. This radius of curvature corresponded to a maximum fiber strain of 0.9 pet. The side faces contained slip bands as shown in Fig. 1. These bands are straight where the strain is high, top and bottom of micrograph, but are curved on either side of the neutral axis in the center. This curvature of the slip bands in the low-stress area may be due to cross slip. The plastically deformed crystal was subsequently electropolished and then electroetched in 10 pct H2SO4 solution, using a current density of 0.25 amp per sq cm. The structure is shown in Fig. 2. The directions of the traces on two adjoining faces were plotted stereo graphically, Fig. 3.* Since there were two sets of

Jan 1, 1968

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

By John Fritz

MEMBERS of the American engineering societies who were in London and Paris during the last days of. June and early July were present at many interesting gatherings. The official delegates of the Founder societies were the specially honored guests of the foreign engineering societies, but other American engineers took part in the meetings. The members of the delegation were: Arthur S. Dwight, Charles F. Rand, William Kelly, representing A. I. M. E.; Ambrose Swasey (general chairman of deputation), Ira N. Hollis, Jesse M. Smith, representing A. S. M. E.; F. B. Jewett, A. E. Kennelly, G. O. Squier, representing A. I. E. E.; Charles T. Main, Robert A. Cummings, John R. Freeman, D. C. Henny, representing A. S. C. E.

Jan 1, 1921

The Library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions are forced to spend a portion of their time in localities isolated from sources of information. To these the Library; through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention: The Library is prepared, to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general Information on the geology and mineral resources of-all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. HARRISON W. CRAVER, Director.

Jan 4, 1919

By Pual M. Tyler

BLIZKRIEG tactics in the present war have consumed metals on such a profligate scale that some of the best-laid procurement plans for civilian and military needs of even a year ago seem in retrospect incredibly meager. Conservation of raw materials has reached an all-time climax in Germany, where metals are worth more than human life and throwing away an empty toothpaste tube may be legally punished by death. Even the United States and the British Empire, proud masters of nine tenths of the world?s known mineral reserves and processing plants, are being driven to metals and feverishly expanding production facilities that not long ago were deemed overbuilt. After the war is over and inevitable postwar readjustments are completed, it is reasonable to expect that purchasing power ? or at least the ability to procure the comforts and luxuries of life ? will be distributed among vastly larger population than ever before, accelerating the rising trend in demand for industrial raw materials in ever greater quantity and variety.

Jan 1, 1942

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.' These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties'3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969