Search Documents

By B Belle

Dust sampling is pivotal in estimating the ‘dose’ of dust exposure and in deriving dose-response curves in epidemiological studies. Over the last half century, gravimetric sampling has been the fundamental means for dust exposure monitoring using recognised respirable size-selective standards. In Australia, a gravimetric sampling technique has been followed since 1983 using the Higgins-Dewell (HD) type cyclones (AS2985). The re-emergence of ‘Black Lung’ or Coal Workers Pneumoconiosis (CWP) in Queensland, Australia has re-kindled the need for better understanding of personal dust monitoring, compliance determination, accuracy, timeliness of sampling results and dust control systems. Reporting dust levels in real time empowers miners and operators to take immediate action to avoid being exposed to excessive airborne dust. Two decades of intensive research in the USA has led to the introduction of gravimetric based continuous personal dust monitors (CPDMs) called PDM3700 as compliance tools. The new real-time mass based sensor is a continuous mass based dust monitor using the Tapered Element Oscillating Microbalance (TEOM) principle and is regarded as significantly superior to the current gravimetric sampling methodology.Recently the overall respirable dust standard in USA coalmines has been reduced from the historic 2.0 to 1.5 mg/m3. This paper provides the results of a comparative pairwise study of an existing gravimetric sampler and the PDM3700 carried out in 3 different Australian underground mines. The field results consistently suggest that there is a significant ‘measurement bias’ between the current gravimetric HD sampler and the PDM3700 monitor operated using a similar HD type cyclone. The results show that the currently used cyclone measurements are approximately 59 per cent higher than the ‘auditable’ PDM3700 monitor data at the current compliance limit of 3 mg/m3. Based on a review of the extensive data collected, the differences can in part be attributed to the aerosol size selectivity of the samplers with the current gravimetric sampler used in mines, collecting more larger sized particles (D90 of 15 µm). This finding has significant consequences for historic exposure results and their use in medical surveillance programs, as well as the current approach to non-compliance determination.CITATION:Belle, B, 2017. Pairwise evaluation of PDM3700 and traditional gravimetric sampler for personal dust exposure assessment, in Proceedings Australian Mine Vent Conference 2017, pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Characterisation of Manganese Ores

Sep 13, 2010

By P Maillet, A J. Crawford, S M. Eggins

TheFiji Islands are remnants of a once continuous Solomon-Vanuatu-Fiji-Tonga volcanic arc (the Vitiaz arc), located at the boundary between the Indian-Australian and Pacific plates. They record a history of: (i)                  arc volcanism the late Eocene to late Miocene, (ii)                an extensive magmatic response to arc rifting (5.5 - 3.0 Ma) during which volcanism was dominated by shoshonitic to tholeiitic basalts, and as rifting continued, (iii)               a transition from arc to intraplate volcanism.   The Hunter Ridge-Hunter Fracture Zone separates the inactive South Fiji Basin from the actively spreading North Fiji Basin, and has been considered to be a transform zone, almost parallel to the motion vector of the Australian plate. However rocks dredged during the 1993 æAlizeÆ cruise, from along the northern part of the Hunter Ridge are typical arc tholeiites, and therefore demand that subduction has occurred beneath the Hunter Ridge sometime during the last ~5 Ma. The Kadavu Island group, south westernmost Fiji, lies at the north-eastern end of the Hunter Ridge-Hunter Fracture Zone, and possibly results from oblique subduction of South Fiji Basin oceanic crust, which may have accompanied the anticlockwise rotation of Fiji during opening of the North Fiji Basin. These islands consist dominantly of 3.4 - 0.5 Ma old medium-high K andesites and dacites, with many traits typical of subduction-related volcanics, ie predominance of intermediate members (55 - 65% SiO2) no Fe enrichment, TiO2<1%, and negative Nb-Ta anomalies. These features contrast strongly with volcanics from elsewhere in Fiji around this time, where volcanic centres produced Om-like intraplate olivine basalts. The Kadavu Islands become gradually younger to the southwest, and show a significant decrease in K2O with time. The north easternmost islands (Astrolabe islands) containing the oldest rocks (~3 Ma) have shoshonitic affinities and are considered to be of similar age and composition to the youngest shoshonites found elsewhere in Fiji.

Jan 1, 1995

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

Japan is the largest coal importer in the world, importing from Australia, China, Indonesia, Canada, Vietnam, etc. In Indonesia, most of the produced coal is extracted from open cut mines. More open cut coal mines will be developed to fill the demand for coal in Indonesia and the world. Many surveys and projects for developing new coal mines and transferring mining technology are being conducted in tropical counties such as Indonesia and Vietnam with the aid of the Japanese Government. It has, however, been pointed out that excessive and precarious development of mines in tropical areas will damage the environments around the mines including cultivated lands, and reduce the precious rainforest. This would undoubtedly exacerbate the instability of the global climate and the food crisis in the world. This paper describes the effects of flyash on the control of acid mine drainage in order to avoid potential negative impacts on the environment caused from open cut coal mines.

Dec 6, 2010

By C E. J de Ronde, I C. Wright

Oceanic subduction-related volcanic frontal arcs extend over 20 000 km within the western Pacific basin and over 21 500 km worldwide, yet they remain largely unexplored with respect to active seafloor mineralization. Systematic exploration of 26 major submarine volcanoes along ~840 km of the Kermadec arc northeast of New Zealand has documented ten (39 per cent) as being hydrothermally active. This frequency of venting is comparable to that on slow-to-moderate rate spreading mid-ocean ridges, which comprise ~80 per cent of the 60 000 km-long global system of spreading centers. The chemistry of fluids discharged from the Kermadec arc volcanoes is moderated by magmatic components in both the gaseous (CO2 + SO2-H2S) and liquid (Fe) phases at very high concentration.The high frequency of venting coupled with chemically rich discharge discovered during this first systematic survey of any arc system forecasts submarine arcs as being important sources of chemicals to the oceans and as potentially lucrative exploration sites for seafloor mineralization. The exploration protocols developed during these surveys include bathymetric mapping of mostly unknown volcanic edifices, followed by detailed water column profiling and sampling to detect and characterize volcanic fluid emission signatures. These procedures are being refined as the survey progresses, both for efficiency and as direct seafloor observations become available for predictive application of water column plume information to guide seafloor mineral exploration.

Jan 1, 2002

Clinoptilolite as a Low-Cost Solution to Remove Heavy Metals from Water in Mining and Mineral Processing Industry

Sep 13, 2010

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

FREQUENTLY the Survey Department is caIled upon to estimate the quantity of material in various dumps, dams piles, etc... and in the carrying out of this work various methods may be employed.The method used will vary according to the particular case in hand, and factors such as accessibility of the top of the dump, steepness of its sides, height, and the condition of the material to be estimated. A certain amount of "give and take" must be adopted in the treatment of small local cavities and mounds.In all cases it is desirable that the surveys made should be tied on to the lease surveys for the purpose of location, and that all levels should be reduced to the mine datum. It is also desirable to obtain levels of the original surface before deposition of the material to be estimated. If these have not been obtained beforehand, levels and transfers round the top will be the next best. If space is availabIe, flat surface is chosen as a site for the dump, etc. This is of the utmost importance in those cases where the material will have to be...

Jan 1, 1925

By J, T C. McCuaig, J Hodgkison, T Fouet

Olympic Dam is the eighth largest Cu deposit and the largest U deposit in the world, with approximately 35 million tonnes of contained Cu and 1.2 million tonnes of U. The most recent resource estimate was for 2.95 billion tonnes of mineralised material with average grades of 1.2 per cent Cu, 0.4 kg/t U, 0.5 g/t Au, 2.6 g/t Ag as contained mineral resources. Olympic Dam is expected to produce >200 000 tonnes of Cu and 4200 tonnes of U3O8 from 9.8 million tonnes of ore in 2004, making it the 12th largest Cu producer in the world. One of the impediments to achieving targeted rates of production has been oversize material (>0.9 m) reporting to stope draw points. A major contributor to oversize material may be overbreak along pre-existing structural weaknesses from stope walls and backs during the production life of a stope. Underbreaking to structures can also have a detrimental effect on the performance of a stope. In an effort to understand the influence of structural geology on stope performance, WMC Resources and SRK Consulting partnered during 2003 to refine the current system of structural mapping, and to use historical data to produce a structural interpretation covering a large part of the mining area. The interpretation has been wireframed in DATAMINETM into a three-dimensional structural framework model. To date, there are more than 600 structures of >50 m strike length incorporated into the structural framework model, which covers a study area 1500 m + 600 m + 350 m. A back-analysis exercise to assess the influence of interpreted structures on overbreak and underbreak was completed for laser-surveyed stopes.

Jan 1, 2004

By T Graham

The invention of the traditional belt and idler conveyor system is attributed to Thomas Robins in 1892. This basic concept, ubiquitous in most mining operations, has not changed markedly in 125 years and still suffers from five forms of energy losses. Firstly, Wheeler, Roberts and Jones (2004) showed that indentation rolling losses, a consequence of the indentation a roller inflicts on the belt, consume 60 per cent of all energy. Secondly, Wheeler (2006) explained that bulk solid flexure resistance resulting from material interaction and movement absorbs 20 per cent. The remaining energy is lost by idler rotating resistance (5 per cent), belt flexure resistance (5 per cent) and secondary resistances (10 per cent).Traditional conveyor systems are continuous as opposed to batch systems, implying both positive and negative features. On one hand, continuous systems have high availability (available infers ‘ready to run’), but, on the other, utilisation of availability is often low; for example, when a conveyor is running empty or below capacity. This converts into reduced system OEE (overall effective efficiency). Many attempts have been made to mitigate energy losses and low OEE issues, including development of rail-based systems. The key drawbacks have been higher capital cost, low flexibility, poor availability and lack of market acceptance.A recent conceptual development known as the ‘autonomous rail conveyor’ (ARC) promises to address issues of energy loss and poor availability and provide increased flexibility by offering solutions for difficult applications. The ARC uses a series of interconnected skeletal bogies covered with a conventional conveyor belt as a load bed running on relocatable light rail. The bogeys have two axles, each driven by integrated variable speed-geared motor and brake systems, and are connected to previous/next bogeys by specialised couplers. Power is provided by a generator (located in a dedicated bogey) and ‘daisy chain’ plug in cables. Centralised redundant control is provided at a preferred point. Although the system is batch in nature, the number of carriages and trains is flexible, meaning that the system is effectively continuous. Loading is achieved by feeding the ARC from a perpendicularly oriented apron feeder, while material off-loading is accomplished by a twist-dump operation in which the belt is twisted through an angle of 50° below the horizontal, causing material to flow from the belt into a receiving conveyor.The ARC system can run multiple trains over any distance, although benefits are more significant in distances of over two kilometres. Capital and operating costs are predicted to be lower than competitive products, with planned maintenance being simple to perform.CITATION:Graham, T, 2017. The autonomous rail conveyor significantly reduces ore haulage costs, in Proceedings Iron Ore 2017, pp 467–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

The results of self potential geophysical surveys conducted over base metal prospects near Orange, Goulburn, and Wellington, N.S.W., indicate that this rapid and inexpensive exploration procedure merits wider application within eastern New South Wales, and in similar environments elsewhere.

Jan 1, 1973

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

By S C. Dominy

The grade of ore at Marvel Loch mine is directly related to the presence or absence of shear zones and quartz-sulfide-rich hornblende (¦ diopside) veining within areas of plagioclase alteration. An experienced geologist can identify these features in hand specimen. Practical rules have been developed to assist this visual identification. The structural sites and styles of alteration and veining most conducive to gold mineralisation have also been determined. The work has enabled a better understanding of the geological controls on mineralisation at Marvel Loch, and has clarified geological understanding for optimisation of grade control modeling, ore block mark-ups, and minimisation of ore loss and dilution during excavation. In addition to this, it has enabled a detailed understanding of mine scale structural controls, geometry and relative grade relationships.

Jan 1, 2003

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

As requested by my fellow members I shall endeavour to read a paper on the Treatment of the Auriferous Sulphide Ores of Kalgoorlie from a metallurgical standpoint. Before going into the subject it will be necessary for me to make some slight explanations. As most of you are aware many of our London friends holding interests in some of these mines think it necessary that their doings should be shrouded in mystery. The result of this is that in some cases it is impossible to get any official figures from the mines for this paper. I must ask you not to lose sight of the fact that in treating the sulphide ores of the Kalgoorlie mines we had absolutely no data to start on, and that to-day. we are just beginning to get a fair grip of tbe subject; and though very high extractions were announced when the first plants were started on sulphide ore, it was well known that this was only to maintain the public confidence in the mines to allow time to make necessary adjustments; and, as showing the advance made in the treatment of the ore, I notice several of the mines have published the results of the final or re-treatment of the residues of their first sulphide treatment. I have also had the opportunity afforded me of thoroughly sampling the residues of several of the principal mines, and find the results as now published absolutely correct.

Jan 1, 1901

The Application of Roasting Pretreatment for Antimonial Refractory Gold and Silver Ores

Sep 13, 2010