Search Documents

By Takasaki Y, Ohzeki S, Hotta H

TO measure high temperature properties of blast furnace burdens ( the change of gas permeability accompanied by contraction, soft- ening and melting ) which govern the gas flow and its distribution, a series of experiments were carried out under simulated blast furnace conditions, using sinter, acid pellets and self -fluxing pellets. 1) The high temperature properties are affected by the ore's reducibility ( up to 1000 -1200¦C ), and the composition, and volume of gangue before reduction. Generally, the burde- ns with high basicity ( Ca0/Si02 ), high reduc- ibility and low volume of gangue have good high temperature properties. Good high temperature properties are : a high temperature at which the gas permeability rapidly decreases, a high melting point and a low maximum pressure drop. 2) Using acid pellets, slow-down of red- uction rate occurs around 1000¦C because the pellet forms a dense metallic shell, while its slag core, resulting from a FeO, Si02 and A1203 reaction, has a lower melting point. 3) The addition of MgO sources improves high temperature properties both of sinter and Pellets.

Jan 1, 1980

By F Cesnik

The past few years has seen a concerted effort to improve the recovery of gold along with its co-product copper from the æhigh-gradeÆ Ridgeway concentrator at Newcrest Mining LtdÆs Cadia Valley Operations. A number of initiatives were identified and implemented, culminating in a sustained improvement in recovery of approximately three to four per cent for both metals. The key projects that contributed to this improvement included the installation of a 355 kW Metso stirred media detritor (SMD) to create a regrind circuit, installation of froth crowders on the scavenger circuit, installation of a Falcon SB2500SE gravity concentrator as part of the regrind circuit to improve gold recovered to bullion on-site and the optimisation of the grinding circuit to reduce the 80 per cent passing size (P80) of the primary grind from 160 to 121 ¦m for the same throughput via process control, cyclone and ball charge optimisation. This paper will focus on the supporting test work, where applicable, that was used as the design basis for the project, but more importantly the plant data before and after the changes to clearly identify the improvements to plant recovery.

Jan 1, 2007

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K Williams, A Lavrinec, V Gurung, D Ilic

The moisture content of iron ore during handling can range from the dust extinction moisture at the point of arrival at the port to the transportable moisture limit at the point of loading ships for maritime transport. Moisture content and ore composition, specifically fines content, have a large influence on ore flowability. Typically, elevated moisture can result in bottlenecks, downtime and lost productivity due to build-up, conveyor carry-back and blockages, increasing maintenance costs. On the other hand, low moisture can result in increased dust emissions influencing the environmental footprint and product losses. Managing the use of water across the supply chain is therefore critical for service life of equipment, productivity, but also has environmental and social impacts, affecting the social license to operate. Previously, experiments have shown that oscillations induced in iron ore during handling and transport can result in movement of moisture through the ore. This kind of moisture migration depends on the nature of these oscillations, such as the undulation of idlers during conveying, the inherent ore properties and the initial moisture content. Moisture has been observed to move either upwards and/or towards the bottom of the burden. These effects can be exploited to remove excess water from the ore influencing handleability and operation, however, the actual mechanisms of moisture migration are currently poorly understood. The study presented herein involves the use of simulation to examine moisture and ore interactions. Simulations using discrete element method (DEM) and coupled with smoothed particle hydrodynamics (SPH) are implemented to investigate the behaviour of moisture in wet ore in the presence of oscillation. This is conducted at a fundamental level first using glass beads and water which is then compared to iron ore at high moisture content. The results of the modelling are discussed in view of experiments conducted.

Sep 18, 2023

Jan 1, 2004

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Li

Cannington Mine has been developing through paste backfilled stopes since the year 2000. These paste drives have been used as either production drill accesses or long-term bypasses. Prior to this study, the ground support requirements for each paste development cut were: an initial 50 mm layer of fibrecrete, weld mesh bolted with 2.4 m split sets, followed by a second coat of 50 mm fibrecrete. Both layers of fibrecrete and the layer of mesh were to be installed before the next cut could be bored and fired. This support regime proved successful at Cannington, however, the total cycle time for each cut was lengthy due to the installation and curing times associated with each layer of surface support. In an effort to reduce the cycle time a study was carried out, with the aid of RocScience’s Phase2 numerical modelling software. The modelling reviewed all of the parameters controlling the stability of a newly excavated development cut. The parameters studied included the early strength of fibrecrete, the ground support load capacity, and the strength of the paste fill masses which varies depending on the cement content. As a result of the study, the ground support standard was revised. The revision has significantly decreased the cycle time as well as fibrecrete consumption, all the while maintaining the safety of personnel and equipment.

Mar 21, 2011

By B Kilgariff

Flotation has been in use at Broken Hill for nearly 100 years, and the process has gone through many different optimisation studies over that time. This paper reviews the current flotation practice at the Perilya Broken Hill Mine, and details one of the recent optimisation studies conducted using mathematical modelling and simulation tools. The optimisation study consisted of surveys of the lead and zinc circuits, mapping of the floatability components of the ore and developing models of the lead and zinc circuits. The models were then used to conduct simulations to simplify the circuit. The study allowed plant personnel to identify optimum operating conditions for their current flotation cells, as well as possible improvements in circuit configuration and cell capacity.

Jan 1, 2005

By M D. Taylor, G Duclaux, K Atkinson, L A. Fisher, A R. Latham, M F. Gazley, S J. de Beer, C M. Tutt

Geological logging by mine and exploration geologists involves the application of a logging code that requires a geologist to make a subjective decision to classify a particular rock unit. This will most likely result in inconsistencies in logging that will be difficult to monitor or assess over time. A potential solution to this problem is to have an objective method to determine the true nature of a given rock unit. This can be achieved using portable X-ray fluorescence technology (pXRF), as large geochemical data sets can be collected rapidly and at low cost. Plutonic Gold Mine (Plutonic), Western Australia, has a growing data set of more than 150 000 pXRF multi-element analyses from core and underground face samples, reconciled to Au fire-assay concentration, and logging codes. This study investigates and statistically validates the consistency with which the logging codes have been applied at Plutonic for the last four years, with respect to both Au distribution and other elements. In doing so, we have developed a schema that allows objective logging to occur once core has been sent for assay and analysed by pXRF. While far from replacing the geologist in the field, this is a complementary method that adds significant value to a data set.CITATION:Gazley, M F, Tutt, C M, Latham, A R, Duclaux, G, Fisher, L A, Taylor, M D, de Beer, S J and Atkinson, K, 2013. Objective geological logging using geochemical multi-element data - Plutonic Gold Mine, Western Australia, in Proceedings World Gold 2013 , pp 455-462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Garvie, D Kentwell, J Chapman

"Most new mining projects require an initial assessment of the locations and volumes of potential acid forming (PAF) waste that is likely to be moved and dumped in surface waste stockpiles. This requires sampling of the waste rock zones and submitting the samples for a series of tests. Key to the outcome of the waste characterisation process is obtaining sufficient samples that are representative of the various rock types both in number and spatial distribution.Various regulatory bodies throughout Australia and the rest of the world are currently struggling with how to define minimum amounts of sampling to achieve realistic estimates without imposing excessive costs and time constraints on a project.This paper addresses two aspects of the process: what constitutes a æsufficientÆ number of samples how to use those samples in determining volumes of likely PAF material.Geostatistical methods of characterising orebodies with large numbers of samples are routinely used in the mining industry by geologists and geostatisticians to estimate and classify Mineral Resources. In theory exactly the same methods can be used to estimate PAF waste locations and volumes.In practice the number and spatial distribution of dedicated PAF waste samples at feasibility stage is typically so small that it is almost impossible to estimate the spatial distribution of PAF material with any degree of confidence at all. Consequently, the common approach is to characterise a few samples from a lithological unit and then assume that they represent the unit as a whole. This approach, however, can be fraught with risk.This paper describes some of the findings of SRKÆs evaluation of several coal projects with respect to PAF waste evaluation and highlights some common misconceptions held by people working in this area that do not have a knowledge of statistics or geostatistics.CITATION:Kentwell, D, Garvie, A and Chapman, J, 2012. Adequacy of sampling and volume estimation for premining potential acid forming waste evaluation using statistical and geostatistical methods, in Proceedings Life-of-Mine 2012, pp 79-88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D R. Swinbourne, T Lehner

Study of the distribution of minor elements between copper matte andfayalite slag is important in determining appropriate methods tomaximise the recovery of valuable metals and the rejection of harmfulelements. Boliden Mineral AB operate a large copper smelter in northern Sweden, where they had noted that the loss of silver to the slag in the settling furnace appeared to be a direct function of the tin content of the slag. This work was aimed at determining whether or not this was a cause-and-effect relationship. Copper matte containing approximately 50 wt per cent copper and small amounts of silver and tin was equilibrated with silica-saturated fayalite slag at 1250¦C, then quenched. The matte and slag were then analysed for their silver and tin contents. It was found that there was no relationship between the silver distribution and the tin distribution. The silver matte/slag distribution ratio had a value of 120 ¦ 40 while that for tin was 2.8 ¦ 0.3. It is suggested that the most likely cause of the relationship observed at the Boliden smelter was matte entrainment in the slag.

Jan 1, 1999

By L A. Martinez Tipe, J McKibben, S Barry

"Metal prices are central to a mineral investment decision and have a profound impact on the financial performance of companies in the mining industry. At its most basic level, metal prices are influenced by the disequilibrium between international metal volume supply and demand. That is, the commodity price is a regulator that equates international metal supply and demand where inventories act as a buffer between the emergence of this disequilibrium and its dissolution through a price change.From this viewpoint, mining companies are required to forecast metal and bulk commodity prices when evaluating minerals projects through discounted cash flow (DCF) analysis. While supply-demand models are instructive, many companies use historical prices, spot prices, futures/forward pricing and consensus opinion (or a combination of all of these) to develop price forecasts.This paper discusses the definition, fundamentals and differences between futures/forward and consensus pricing and the appropriateness of each in a DCF model for mine project economic evaluation.Our results demonstrate that great care is required when using either futures/forward or consensus pricing and that the decision to use one rather than the other requires consideration of other important elements in the DCF model (ie the risk-adjusted discount rate).CITATION:Martinez Tipe, L A, McKibben, J and Barry, S, 2016. Metal prices and the differences between forward and consensus pricing – which one is better for use in a discounted cash flow model?, in Proceedings Project Evaluation 2016, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Gillies A. D S

Rail, port and shipping charges represent 30 to 50 per cent of landed costs for Australian coal mines selling to Asia. This proportion is higher for sales to Europe, yet it is in Europe where Australian producers are aiming for increased market share. The landed cost of coal to the international customer is the key parameter which determines market competitiveness. The objective of this study is to examine Australian export coal competitiveness in terms of transport distance. The approach used examines world coking coal and steaming coal production and the transport distances between major exporting regions and importing countries. Reference is made to the importance of land transport costs and a comparative approach for emphasising the relative magnitude of this factor is developed. Models developed are examined in terms of Australia's exports and a conclusion is reached that a reduction in rail freight costs would be an effective measure for improving the competitiveness of Australia's coal industry.

Jan 1, 1994

By X Zhang, B McFadzean, P E. Ngoepe, B Nemutudi, P P. Mkhonto, S Pikinini

There is still a huge challenge in efficiently recovering the arsenides minerals that are largely concentrated in the Platreef Bushveld Complex which constitutes about 21 per cent of the platinum group minerals (PGMs). Therefore new collectors are required to improve the recovery separation of hard to float minerals, in particular sperrylite. The triazine modifications are promising reagents for mineral flotation and have not been given much attention in minerals processing. The adsorption of sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT), sodium 2,6- ditrithiocarbonate-4-butylamino-1,3,5-triazine (SDTTCBAT) and sodium normal butyl xanthate (SNBX) on sperrylite (100) surface were performed to identify a well performing collector molecule. We observed that the triazine collectors preferred to bridge on surface As and Pt atoms through the S atoms. We found that the adsorption energies were in the order: SDTTCBAT > SDTBAT > SNBX, indicating that the SDTTCBAT had strong exothermic adsorption on sperrylite and pyrite. These results showed that the ditrithiocarbamate had a great influence in the adsorption strength on the sperrylite surface. Importantly it was found that the triazine collector had stronger adsorption than the xanthate, which portrayed a promising replacement of xanthate collector. These results paved a way for design of novel collector for sperrylite and other chalcogenide minerals to improve their recovery.

Aug 24, 2022

By S Raval

The estimation of greenhouse gas emissions from coalmines is increasingly becoming a priority for both operators and regulators. At the same time, involved scientific challenges in the methane measurements is generating significant interest from global research community. Various technology providers are also actively engaged in improving their sensors and platforms to address the measurement challenges and capitalise the market opportunities. This presentation highlights rapidly evolving multifaceted landscape of coalmine greenhouse gas emissions. It covers the advances in sensors for the detections, including ground-based, airborne, and satellite-based systems as well as models for the emission estimations, including attempts to reduce the involved uncertainties.

Sep 1, 2024

By G Fergus, M Hart, S W. Weeks

Rio Tinto Alcan has undertaken feasibility level assessments into the expansion of its bauxite mining operation in an area south of the Embley River in far north Queensland. The project has the potential to extend their Weipa operations by approximately 40 years.The construction and operation of two additional mineral ore processing plants are proposed for the South of Embley project. Golder Associates was engaged to develop and conduct modelling assessments of potential sources of water supply required by mineral ore processing.Two models were developed using GoldSim: a dam yield model and a water balance model. GoldSim is a graphical object-oriented modelling environment with a capacity to carry out dynamic probabilistic simulations. Originally developed by Golder, GoldSim has been applied successfully in a decision support role to a range of mine water management operations.The dam yield model was used to provide estimates of reliability and volume of annual water supply of several potential surface water dams. This information was then used to determine a hierarchy of water supply options for processing plant operations. The water balance model dynamically simulated the water demands of the two production plants and the consequential response in water supply, with respect to the timing and discharges provided by the various source options.Use of the model provided a preliminary operational tool to assist with water supply management decisions. Water quality issues required a blending of water from separate sources and attention paid to scheduling to ensure water supply through the dry season. The model also helped identify risks to water supply in the event of underperformance of one or more water supply sources. This allowed the operational rules to be refined to minimise those risks.The dynamic and stochastic modelling approach provided a method for identification of water supply issues susceptible to seasonal climate variability.CITATION:Weeks, S W, Hart, M and Fergus, G, 2013. A dynamic evaluation of water supply security susceptible to climate seasonality, in Proceedings Water in Mining 2013, pp 197-208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015