Search Documents

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993

By I M. Howard

With the bell-less top (BLT) charging system replacing the centuries old double bell charging method, the furnace efficiency has been greatly improved together with considerable reduction in the furnace down time and operational problems. But still there are many draw-backs which need further attention to achieve better efficiency and operational effectiveness. The performance and operational problems of the BLTs have been highlighted and possible solutions to overcome some of the major problems are discussed.

Jan 1, 1999

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L Lorenzen, H Muller, L Bernard

Australian companies and consultants are becoming ever more involved in projects in African, South American, East European and Middle Eastern countries. However, significant differences in culture and approach to projects sometimes make these projects challenging for reasons that are not purely technical. Often the challenges are rather related to how the project owner and local authorities perceive the reality. These perceptions and sometimes unrealistic expectations regarding project costs and potential outcomes need to be addressed by the æWesternÆ project developer and consultant.This paper will discuss the specific experience of Snowden in studies commissioned by companies from such countries for the development of very large, low-grade gold deposits in some of the most inhospitable areas in the world. The paper will further review similar projects undertaken in other ænew worldÆ countries and compare these to the initial Snowden experience.As the process operating costs of operations in many of these countries are extremely competitive when compared to the typical Australian operating costs, the paper will review the operating costs and the factors which may be pertinent to a large project of this nature, both in the Australian and the ænew worldÆ context. Will Australian-based operations be able to compete in the global gold market when the gold price softens again, as it will do at some stage in the possibly not-so-distant future?CITATION:Muller, H, Lorenzen, L and Bernard, L, 2013. Challenges of developing low-grade deposits in ænew worldÆ countries from a mining consultantÆs perspective, in Proceedings World Gold 2013 , pp 307-314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D Cooke

In 2010, Kalgoorlie Consolidated Gold Mines (KCGM) was Australia’s largest gold producer, with total annual production of 788 000 ounces. Of the gold produced by KCGM in 2010, 95 per cent was extracted from the Fimiston open pit, also known as the Superpit. The Fimiston operation encompasses the historic Golden Mile, from which more than 55 million ounces of gold have been extracted from the world-class Fimiston lode style mineralisation.The operational performance of the KCGM Fimiston open pit was reviewed for the period between 2005 and 2010. Key performance metrics reviewed included mined tonnes and grade, cost per ounce of gold produced and the mine to mill reconciliation trends. The years 2007 and 2008 were characterised by a decline in performance against key performance metrics. The ore zones were diluted, with the excess tonnes mined resulting in lower grade and an increase in the cost per ounce. Poor reconciliation between ore mined, the ore reserve model and the grade control polygons was also observed.A series of improvement initiatives were implemented in late 2008. As a result of changes made to the grade control and mining practices, the site performance recovered. Unplanned dilution was reduced, which had a positive impact on mined grade. The lower tonnes combined with higher grade reduced the cost per ounce to below budgeted levels in 2009 and 2010, enhancing the profitability of the operation. The operational performance between 2005 and 2010 was compared to the turnover statistics for the KCGM geology department over the same period. Turnover accelerated between 2005 and 2007, peaking at an annualised rate of 43 per cent. With the onset of the Global Financial Crisis and the implementation of retention initiatives, turnover reduced significantly between 2008 and 2010. A strong consistent correlation was observed between the turnover trends in geology and the performance of the grade control function and resultant site metrics.The cost of turnover is known intuitively, however, rarely quantified. To evaluate the benefit of the improved performance, a detailed financial model was used to quantify the impact of the grade control function. In 2010, the headgrade exceeding budget by just four per cent contributed an additional A$24 M of value to KCGM. In contrast, if the 2008 performance had been replicated in 2010 (-9 per cent on headgrade), the result would have removed A$61 M in value from the business. The KCGM experience between 2005 and 2010 demonstrates the value of human capital in a mining operation and the importance of a high performing geology grade control team to the profitability of a mining operation.

Aug 22, 2011

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

By D MacKay

The Mt Wright Project is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. Underground Development of the current Mt Wright orebody commenced in June 2006 and the first production ore was brought to surface in June 2007. The orebody is a rhyolite pipe containing fine-grained disseminated gold in a granite host rock. Ground conditions tend to be good to excellent throughout development, with some minor deformation experienced when stope-sized excavations are formed. The mine commenced as a sublevel open stoping (SLOS) operation with the intent to utilise development waste to back fill isolated upper level stopes while developing to the bottom of the known orebody. The mine plan intended to commence production with a bottom-up primary/secondary stoping retreat through the main orebody utilising cemented fill. Some challenges were faced during the initial production phase that included:•Ongoing underground diamond drilling and updating of the block model resulted in some issues reconciling the grade control results to the resource model. This was primarily due to the high variability of grade which in turn caused difficulties in accurately identifying areas of low and high-grade.•The cost of establishing and operating a cemented fill plant to achieve the planned extraction sequence of the orebody had increased significantly beyond initial estimations.•Geotechnical conditions such as stress orientations, ground behavior and response to the forming of excavations learned through the mining of the upper level stopes were different to the assumptions made during the initial design.A number of in-house and external reviews of the mining method were completed which has resulted in a revised mining plan. This paper will summarise the challenges faced and the implementation of the mine plan to date.

Mar 21, 2011

By S E. Box, J L. Mauk

The Middle Proterozoic metasedimentary rocks of the Belt Supergroup contain important metallic mineral deposits like the diagenetic sediment-hosted stratiform copper mineralization, including the Troy (Spar Lake) deposit and the epigenetic hydrothermal veins in the lower Belt and Ravalli Group in the Coeur d'Alene district. Magnetite (Fe3O4) is a common and widespread accessory mineral in these rocks and can have multiple origins including ore stage in deposits, mobilization stage in source rocks, metamorphism of red beds and alteration mineral in thin halos enveloping Ag-rich veins in the Coeur dÆAlene district. As shown in several classic studies, the composition of magnetite from igneous rocks varies significantly in response to controlling factors such as melt composition, temperature, silica activity, and oxygen and sulphur fugacity. Therefore, the distinctively different geologic settings within the Belt Supergroup strongly suggest that there may be differences in the magnetite compositions. However, initial microprobe analyses detected no variation in magnetite composition.   Three possibilities may give an adequate explanation for these initial results: 1.      the magnetite formed primarily as pure Fe3O4, 2.      one or more tectonothermal events led to regional scale re-equilibration that affected all rocks in the field area, and 3.      the variations in the composition are below the detection limit of the microprobe.

Jan 1, 2007

By Y Shougu

Many mine accidents will affect the mine ventilation system when they occur. At present, there is a lack of monitoring means to capture the occurrence of accidents in time by monitoring the ventilation system, so as to take emergency measures to reduce the loss of personnel and property. Pressure wave is an elastic wave existing in air. Most accidents in mine will cause obvious changes of pressure wave. It is an innovative idea to monitor the occurrence of accidents in mine by measuring pressure wave. The development and functions of the pressure monitoring device and related software are introduced in detail. The pressure wave monitoring test is carried out in San Xavier underground mining laboratory, and the D-wave and S-wave waveform data are collected. The waveform characteristics are analysed, and the main frequency distribution of the pressure wave is found to be within 1 Hz by using FFT. At the same time, the influence of the propagation distance of the pressure wave on the waveform is analysed. The propagation velocity of D-wave and S-wave are roughly calculated, and they are 279.6 m/s and 397.3 m/s respectively. S-wave is slightly faster than D-wave. Although there are errors and uncertainties in the test, the test verified the feasibility of the existence and collection of pressure waves in the ventilation roadway, and provides a method for the future study of the propagation of pressure waves in the mine ventilation system.

Oct 12, 2022

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By E U. Petersen, D R. Cooke

Hydrogen and oxygen isotopic constraints on hydrothermal fluid composition from the Pliocene Boyongan and Bayugo porphyry copper-gold deposits (southern Philippines ) reveal mixing of magmatic and sea water reservoirs as the hydrothermal system evolved. Magmatic-equilibrated fluids (d18O: +8.3ë to +9.1ë; dD: -61ë to -51ë) are represented by hypersaline brines implicated in copper-gold transport and deposition. These dominate the fluid inclusion assemblage in early comb-quartz (unidirectional solidification textures), miarolitic quartz, and in K-silicate-stage quartz-K-feldspar ¦ biotite veins. Fluids responsible for post-K-silicate alteration assemblages of pyrite-clay (illite, pyrophyllite and kaolinite), alunite and smectite are represented by low-moderate salinity two-phase inclusions in co-existing quartz. These are interpreted as mixtures of evolved magmatic fluids (d18O dD: -42ë to -20ë) with evolved Pliocene sea water (d18O: + 4.0ë; dD: +4ë). The isotopic evidence for sea water involvement in the hydrothermal system suggests that porphyry emplacement and associated diatreme formation could have occurred in a submarine setting. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By A Self, B Robertson

During 2015 and 2016, the authors conducted a number of surveys, workshops and reviews of ventilation and gas management practices in Australian underground coalmines. The study was funded by ACARP with a brief to identify gaps in ventilation and gas management practices for current and future needs, and to prepare a road map for change that would assist in delivering improvements.The study found that despite many examples of leading practice, gas and ventilation management is not afforded the attention and priority that is warranted and that this must be remedied if future operational performance targets are to be achieved and the safety of the industry protected. This paper summarises the findings of the study and presents the recommendations proposed.CITATION:Robertson, B and Self, A, 2017. A review of ventilation and gas management in underground mines, in Proceedings Australian Mine Vent Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

In the last 40 years, New Zealand has developed a number of liquid- dominated geothermal steam fields, for electricity generation and indus- trial process steam. New technologies were developed, and in this work, New Zealand led the world. The policy of full publication of the results, in a wide range of sciences, provided a reservoir of detailed data defin- ing the geology, size and shape, and the chemical and physical regime, of many geothermal fields and their constituent parts. The discovery of precious and base metal deposits /precipitates in geothermal drill cores and steamfield equipment, suggested a clear link- age with epithermal mineral fields in general, and with that of the Coromandel (Hauraki) Region in particular. Further work on geothermal/ epithermal relationships have implied that the techniques, developed to obtain an understanding of geothermal fields, could be applied also to epithermal mineral exploration. This work is developing fast, and is now proceeding in many coun- tries. Future work may show that the presumed relationship between geothermal and epithermal deposits may be applicable in the wider con- texts of all hydrothermal deposits, and possibly in many other minera- lised areas with volcanic "country rocks".

Jan 1, 1988

By F M. Weir, M Fowler

The design of excavations in rock must, implicitly or explicitly take into consideration the influence of small- and large-scale geological structures. For most sites the complexity of a fractured rock mass is best captured using a 3D fracture system model based on field data. A discrete fracture network (DFN) approach involves stochastic modelling of the ‘smaller scale’, nondeterministic structures. For slope stability or tunnelling projects DFN modelling provides a valuable geotechnical tool for characterisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of the DFN modelling undertaken for the design of a large open pit in Australia. The proposed pit is to encounter a 160?m thick, high strength, sheared shale unit, which overlies a crystalline basement. DFN modelling was undertaken separately for both the shale and basement units. While the model inputs and development for each unit are briefly presented, the focus of this paper is on the various applications of the DFN modelling.A key advantage of the DFN approach for design studies is its probabilistic application to structural analyses and results. Multiple realisations of the same model were generated for both the shale and basement units, with the stability analysis carried out on each iteration. The generation of a large number of DFN models and analyses allow assessment of wedge volume, factor of safety and proportion of unstable slope for a range of conditions. The DFN modelling at the case study site was also utilised for a number of other purposes. For example, investigation of likely fault lengths in the shale unit and combined rock mass and defect failure. The development of this tool has been influential in improving our understanding of fracture networks for excavation design.CITATION:Weir, F M and Fowler, M, 2014. Rock mass characterisation and analysis for excavation design – a discrete fracture network approach, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 445–456 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Spleit

A long-term production schedule for the LabMag iron ore deposit in northern Quebec, Canada is derived using stochastic integer programming. The optimisation formulation maximises the schedule’s net present value while simultaneously managing the risk of deviations in production tonnages and qualities by considering stochastic simulations of the orebody instead of a single deterministic model. The formulation also smooths and minimises haul truck requirements and ensures that as mining progresses, space is created within the mined out pit for the return of waste material.CITATION:Spleit, M, 2014. Production schedule optimisation – meeting targets by hedging against geological risk while addressing environmental and equipment concerns, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 397–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A J. Weston

Block or panel caving technology is far removed from that of the top slicing and block caving of the late nineteenth or early twentieth centuries. The rapid mechanisation and expansion of these methods in the late twentieth century was as much a result of the change of the technology of the unit operations of development, ground support, drilling and blasting and transport as it was of the advances in geotechnical understanding and practice. The small footprint gravity and scraper block caving mines with boundary weakening, rail transport and shaft hoisting of the early to mid-twentieth century have been replaced by massive high lift panel caves using preconditioning of the ore, large load-haul-dump units, adjacent crushers and conveyors to surface. The technology changes in the unit operations are described and the drivers for these changes examined.CITATION:Weston, A J, 2016. The evolution of block caving technology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 265–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Brown N. R

This paper attempts to highlight some of the problems encountered in the economic exploitation of the deeper coal seams by opencast mining methods. The major cost elements of three methods of overburden removal are examined in relation to the overall cost of winning coal from deeper-lying coal seams. The three overburden removal methods examined are dragline stripping and two systems combining dragline stripping with shovels and trucks at varying depths of overburden. A dragline is, undoubtedly, the most cost effective system of overburden removal for depths of up to 30 metres but it is suggested that, when dealing with incremental overburden depths in excess of 30 metres, engineers should consider carefully the possibility of using a shovel and truck operation, or other system, to augment the use of a dragline.

Jan 1, 1986

By Johnson M. W

Factual data about the sedimentation in the Newcastle Coal. Measures are presented. Data concerning the total coal measure sequence (isopachs, sand /shale ratio and total coal thickness variation), data about three coal seams (Borehole, Dudley and Victoria Tunnel) and data about interseam con- glomerate units are discussed. From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin. The northern and north-eastern edge, which was unstable, suppl- ied most of the coarse detritus including the conglomerates to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern - each shows development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure. Evidence of in-situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.

Jan 1, 1969