Search Documents

By S C. Dominy

The gravity recoverable gold (GRG) parameter reflects liberated gold or gold-dominated composite particles that can be recovered by gravity separation. Recoveries depend upon mineralogy, in situ particle size and the comminution and extraction method used. Any ore bearing >15 per cent of gold greater than 50 ¦m in size is likely to have a GRG component. The principal characterisation methodology applied is the three-stage GRG (3GRG) test, based on a 40 kg to 100 kg sample. An alternative is the single-stage GRG test (SGRG), which is generally based on a 20 kg sample. Experience has shown that GRG values can vary throughout an orebody, particularly within different grade and/or mineralogical domains. Test programs must consider sample frequency and mass. This study demonstrates the variability of GRG results based on different sample masses. Consecutive underground faces on a coarse-gold dominated quartz vein were sampled taking five different masses from each. Each sample was processed using a SGRG approach. Subsequently, each development round was batched through a small gravity production plant. The results show that the small samples understate the plant GRG and show inter-sample variability. Large samples show less variability and a SGRG closer to the plant GRG. A high SGRG broadly correlates to higher gold grades, more coarse gold and larger gold particles. These results are intuitively correct, but indicate the likely challenges of sampling for gold recovery in heterogeneous systems.CITATION:Dominy, S C, 2013. Variability of gravity recoverable gold values in relation to test sample size, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 293-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By J Coombes

Within the mining industry there is a growing trend of placing inexperienced technical people into positions of responsibility beyond their readiness. Their responsibilities often include providing the fundamental basis for decision-making: the resource model or even the daily grade control estimates. Whilst software continues to make the processes more accessible, the thinking and rationale for selecting parameters still requires control rather than auto-piloting. Operators run these systems in virtual isolation, and have limited immediate access to experts. Beyond the stress of the professional burden are the increased risks to the mining operations and overall project success.While many experienced experts recall being thrown in the deep end, the relative isolation from experts coupled with the gravity of professional burden before readiness, is less familiar. Many recall in intimate detail the experts who gave them direction, assisted them along the way and even helped them claw out of inadvertent mistakes. Experienced professionals all have a responsibility to enable capability across the generations, to ease the burden and to mitigate the risks.This paper provides an outline of how mentoring as an on-the-job professional development process can be structured to more fully enable success of a mentoring program. Three examples complement the principles presented.CITATION:Coombes, J, 2012. Structuring meaningful mentoring, in Proceedings International Mine Management 2012, pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By S Ferguson, G Noble

The mining industry is facing economic pressures to treat more challenging and lower grade ore types, as well as pressure relating to environmental impact and social license to operate. Preconcentration through bulk ore sorting has the potential to benefit all these areas by enabling mining operations to divert material of low economic value prior to processing, thereby achieving higher feed grades and recovery, while reducing the processing plant and tailings dam footprint and capital required throughout the life of mine. The effectiveness of bulk ore sorting depends on the heterogeneity of material at the measurement location, as well as the accuracy and precision of the measurement. An understanding of ore heterogeneity can be assessed using drill core data, which provides metre by metre elemental assays. This paper reviews such data and assesses the grade distributions over different scales, which suggests that sufficient heterogeneity exists at mining scales to allow the potential for bulk ore sorting. Prompt Gamma Neutron Activation Analysis (PGNAA) technology has proven to be a successful measurement technique within many industries, including mining. PGNAA was first developed in the early 1980’s for the measurement of the elemental composition of bulk materials on a conveyor belt. Today, Pulsed Fast Thermal Neutron Activation (PFTNA) technology is also applied in elemental analysis of bulk materials and has some advantages for bulk ore sorting. In order to enable effective bulk ore sorting, however, a PGNAA/PFTNA analyser must be designed to provide a representative bulk ore analysis with the necessary accuracy and precision. Examples are presented to provide an understanding of the factors affecting PGNAA/PFTNA performance in relation to effective bulk ore sorting.

Nov 10, 2020

By T Baumgartl, B Noller, B Forsyth, J Park, M Edraki, P Pham

Understanding and quantifying residual risk is the key to the successful closure and rehabilitation of mines. An important aspect of residual risk is predicting the long-term chemistry of mine water and the long-term geochemical stability of mining wastes. This requires updating the characterisation data for mine wastes and monitoring mine drainage throughout the life-of-mine. The intrinsic properties of waste materials (ie the geology, mineralogy and the weathering processes, which in turn depend on the local climate and water balance in a waste storage facility) are the fundamental controlling factors of residual risk. In this paper, case studies of coal and metalliferous mines are used to discuss the definition of residual risk for a range of waste storage facilities and to highlight the benefits and limitations of current geochemical methods in predicting and quantifying residual risk. Consistent with the classification of mine drainage by the Global Acid Rock Drainage Guide, three case studies of acid, saline and neutral drainage are presented.CITATION:Edraki, M, Pham, P, Park, J, Baumgartl, T, Noller, B and Forsyth, B, 2016. Defining residual risk for successful mine closure – a geochemical perspective, in Proceedings Life-of-Mine 2016 Conference , pp 9–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R C. Morris

Two major types of economic secondary iron ores occur in the banded iron formation (BIF)-rich Hamersley Province of the Pilbara, Western Australia:dominant BIF-hosted bedded iron deposits (BID)detrital ore deposits (DID sensu lato), which are mainly hosted in the three province-wide Cenozoic sequences that include coeval non-ore sediments and comprise:a. the major Miocene, fluvial channel iron deposits (CID)b. the lesser Eocene and Pliocene detrital iron deposits (DID sensu stricto).Striking differences exist between the massive CID resources and the much smaller underlying and overlying DID. CID are essentially riverine alluvial ooidal rocks with abundant small fossil wood fragments and variable iron peloids, but with only extremely rare recognisable lithic remnants. The original matrix is typically ramifying layered goethite. Eocene DID are mainly alluvial with minor pisoids, whereas Pliocene–Quaternary DID are dominantly coarse colluvial gravels, both derived from and largely retaining the original textures of BID, hard cap or variably ferruginised surface BIF. The colluvial DID matrix is typically ferroan-aluminous soil, resulting in canga where replaced by goethite, which may be dehydrated to hematite by exposure. The Cenozoic deposits occur in two dominant geomorphological environments: the southern Marra Mamba to Brockman Iron Formation strike valleys containing all three Cenozoic sequences and the much later northern Brockman Iron Formation plateau valleys that include only the Miocene and Pliocene sequences. The Cenozoic detritals formed in different climatic regimes, with an extended dry period forming a prominent province-wide dehydrated carapace on the Eocene DID. The Miocene ‘optimum’ followed with its thick scrub-covered deep regolith that produced the fossil wood-rich CID and was succeeded by the arid cool period of the Oakover limestone/calcrete. A major renewal of exposure and erosion in the Pliocene resulted in the extensive iron gravels of the Pliocene–Quaternary.CITATION:Morris, R C, 2015. The Cenozoic detrital iron deposits of the Hamersley Province of Western Australia – a tribute to Mal Kneeshaw, in Proceedings Iron Ore 2015, pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Shrimali, P Rajmeny, L Shekhawat, A Joshi

Rampura Agucha open pit mine has successfully been excavated to a depth of 320 m, incorporating multistage working. The key to success is the implementation of presplitting as control blast measures at every stage of mining, including intermediate cut backs, in addition to the final wall. The major challenges encountered in establishing presplitting in the hang wall as compared to the footwall of the mine are:reversely dipping foliation, ie dipping into the hang wall itselfstriking obliquely at an angle of 20–30° with regards to the general strike of the pit wallthe presence of numerous geological planes of weaknesses like major faults, slips, etc.Control blast parameters like hole inclination, spacing and stand-off with buffer row were chosen initially from the literature survey and were subsequently fine-tuned by field trials to the mine geo-mining conditions of the hang wall. Electronic initiation used for trim blasts along with double presplitting in fault-affected zones helped in getting better presplit performance and resultant stability of the hang wall.CITATION:Rajmeny, P, Shrimali, R, Shekhawat, L and Joshi, A, 2015. Establishing the design parameters of a control blast for long-term stability of the hang wall at Rampura Agucha Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Hoberg H, Schneider FU

Flotation tests were conducted with galena, quartz and with synthetic mixtures of the two, in different ranges of grain size, and with different process parameter variants. Physico-chemical analyses were also carried out on surface energy and on xanthate adsorption on galena with different grain sizes. Reference will also be made to hydrodynamics, interfacial chemistry and the influence exerted by grain size in flotation.

Jan 1, 1993

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

By D Hume

During 2001 the Ridgeway Gold Mine, driven by company initiatives and recent NSW legislation (General Rule 2000), developed and implemented Major Hazard Management Plans to control significant hazards identified at the underground mine. The paper presents the objectives, issues, outcomes and process involved in the development and implementation of the plans at Ridgeway. The sharing of the experience gained and an overview of the intended way forward will offer a valuable insight for other mines considering embarking on a similar journey.

Jan 1, 2002

By B W. Atkinson

Full-stream mechanised sampling apparatus, that collect a full cross-sectional increment from the complete screen discharge, will always be the preferred option for sampling screen overflows. However, the reality is that provisions for automated sampling are rarely, if ever, provided at the discharges of individual screens within beneficiation plants.Sampling from the discharge of high capacity vibrating screens, especially multi-slope screens, is subject to sampling bias, due to the stratification of the ore that occurs on the vibrating screen deck. The stratification in the vibrating bed translates to a stratified falling stream at the discharge end of the screen, typically with smaller particles at the back of the falling stream and large particles at the front of the falling stream (Figure 1).The chemical and physical characteristics of heterogeneous ore (mineral or coal) particles vary significantly with particle size. If samples do not correctly reflect the source material size distribution, they will be biased and the resulting analytical/assay data will not reflect the actual physical nor chemical characteristics of the source material.Prior published data for coal preparation research (Australian Coal Association Research Program) has demonstrated that a bias appears to exist for samples collected from high capacity multi-slope screens.A new form of sampling scoop has been developed with the aim of overcoming this issue.Bias was evaluated at a coal preparation plant by comparing the desliming screen overflow size distribution to that for æreferenceÆ coal preparation plant feed samples collected using the recognised stopped-belt technique. The study procured 20 sets of comparison samples in order to ensure statistical relevance.Two forms of sampling device were employed for the multislope screen discharge.A conventional square aperture scoop was demonstrated to exhibit a significant coarse bias, in that the resulting samples exhibited a significantly coarser size distribution compared to the reference samples. In other words it was evident that the conventional scoop æfavouredÆ material from the front of the falling stream.A new æcollapsibleÆ sample scoop was evaluated in parallel, and its samples were found to exhibit no relevant bias.CITATION:Atkinson, B W and Swanson, A R, 2012. A new method for sampling from high capacity screens, in Proceedings Sampling 2012 , pp 89-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Ehlert G, Steinlechner E

The paper describes a new process for filtration which combines the continuous operation of conventional vacuum filters with the low final moisture contents hitherto only achievable with plate and frame presses. The increasingly high portion of fine particles causes several problems in the filtration of copper concentrates. One drawback is that remarkable quantities of liquid are attached to the very fine particles because of their specific surface area. Furthermore, fine particles also reduce the size of the capillaries in the filter cake, thus increasing the critical pressure which any filtration system has to exceed to achieve the desired final cake moisture. The maximum filtration pressure of conventional vacuum filters is limited by nature itself and by practical aspects to approximately 0.75 bar. The hyperbaric filter combines the continuous operating principle with an increase in filtration pressure of up to 6 bar simply by placing the entire disc or drum filter inside a pressure vessel. The major machine components and process features are explained in the details of the paper. After extensive research and field testing, 23 ANDRITZ hyperbaric filters, with a total filtration area of 1968 m2 have now been sold. Seventeen of these units (1440 m2) are in commercial use and more units are, on order. Performance data on copper concentrates from plants in Australia, South America, Poland, Africa and North America are outlined in detail. Compared to vacuum filters, generally hyperbaric filters will reduce the final cake moisture of concentrates with 75 per cent

Jan 1, 1993

By I Canbulat, J Emery, L Yao and C Zhang

This paper documents a process of data analytics and machine learning applied to coalmine roof convergence data. It follows a publication documenting the formation of the database. For each set of analyses Python scripts were utilised to extract data from an SQL database, with subsequent analyses also executed in Python, utilising open-source tools such as scikit-learn. Preliminary analyses with classic machine learning algorithms included multiple logistic regression, K-nearest neighbours, decision tree, random forest, support vector machine, kernel support vector machine, artificial neural network (ANN), naïve Bayes and multiple linear regression. Results indicated that relationships were complex and non-linear, with the artificial neural network most suitable. An ANN model was then refined through a standard process of hyperparameter optimisation and data augmentation to arrive at a final model. Due to the black box nature of the ANN further insight into how the parameters interacted was sought and found with Shapley additive explanations (SHAP values). SHAP values utilise Game Theory, where each input parameter or feature is a ‘player’ while the data set is the ‘team’. The SHAP value is the impact of each player on the target value, essentially establishing the contribution of each input parameter. The results from all analyses are delivered in the paper, together with insights, applications, strengths, and limitations of the methodology.

Nov 29, 2022

By R Pinksen

The Iron Ore Company (IOC) of Canada Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1 m × 1 m × 1 m) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion into the blastholes provided more resistance to the forces created by dynamic water and reduced the infi ltration of the emulsion into the cracks and fissures of the rock mass. Blast results showed reduced amounts of oversize and more consistent fragmentation throughout the muck piles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realised.To determine the effectiveness of the oversize reduction project, IOC used shovel based camera technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with global positioning system (GPS) locations. A large population of digital images was analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jul 11, 2011

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987