Search Documents

By Aziz N

The objective of the paper is to develop an understanding of the influence of caving on powered support rating by examining the geology and support performance at two sites which represent the current extremes in support rating, ie 6/240 Ton supports operating in the Hirst Seam at Solsgirth Colliery, Scotland, and 4/900 Tonne supports operating in the Bulli Seam, West Cliff Colliery, Australia. A conceptual model is introduced which considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata. Different caving mechanisms are identified for the strata of the Hirst and Bulli Seams, ihese mechanisms being related to rock properties, ie to the palaeogeography and depositional conditions at each site, producing caved wastes with different yield characteristics. The results obtained for convergence and support reaction during production cycles at both sites are analysed to show the manner in which support reaction is developed, indicating the importance of high setting load densities in the Bulli Seam. Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations, ie the powered support and the caved waste immediately behind the powered support, is used to further demonstrate the influence of caving mechanisms on support rating.

Jan 1, 1986

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By A G. Tomkins

"Approximately 32 per cent of the worldÆs total gold production has come from greenstone belts (Frimmel, 2008). In these regions numerous small to large, quartz vein-associated gold deposits are hosted in metamorphic rocks ranging from lower greenschist to granulite facies. Historical exploration has focused its efforts on rocks of greenschist to lower amphibolite facies because these seem to contain the most deposits. Consequently, these regions are now reaching mature brownfield status, particularly in developed nations, and finding new deposits is becoming progressively more difficult. In comparison, regions of similar tectonic setting, but instead containing high-grade metamorphic rocks of mid-amphibolite to granulite facies, have received little attention because the first explorers found fewer deposits there.However, these regions certainly do contain some very significant gold deposits such as Hemlo in Canada (~684 t Au), Renco in Zimbabwe (~31 t Au mined since 1980), the very profitable Challenger deposit in South Australia (~36 t Au; recovered + reserve + resource), and the most recently discovered Tropicana deposit in Western Australia (~182 t Au; reserve + resource). High-grade metamorphic terrains therefore offer explorationists an excellent opportunity to move onto relatively green fields within developed nations, which carry less risk associated with development. However, explorationists have comparatively little knowledge of the geological controls on gold distribution in high-grade terranes because: industry experience lies in traditional lode-style gold deposits these gold deposits are geologically more complex there has simply been minimal research conducted on these deposits as a holistic group.Furthermore, research conducted in the last five years has shown us that the previous widely accepted model for gold genesis in these terranes, the crustal continuum model, is incorrect. Here, I discuss features from several gold deposits hosted in high-grade metamorphic rocks and use these to define two categories for explorationists to consider: deposits that formed prior to peak metamorphism (metamorphosed gold deposits) deposits that formed well after peak metamorphism (post-metamorphic gold deposits). There are none that have been convincingly shown to have formed during peak metamorphism.CITATION:Tomkins, A G, 2013. Gold deposits in highly metamorphosed terranes, in Proceedings World Gold 2013, pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By A Taheri, G D. Nguyen, M Karakus, S Akdag

During underground mining operations, rock masses are highly subjected to dynamic disturbance caused by blasting, mechanical drilling and earthquakes resulting in strain burst, slabbing and spalling. The dynamic fracture is a significant manifestation of rock failure in deep underground engineering, and it is of great importance to assess the dynamic fracture behaviour of the rock mass under elevated temperature conditions. The correlation between temperature – and loading rate-dependent dynamic fracture mechanism of strain burst is yet to be established. A good understanding of the dynamic fracture behaviour of brittle rock subjected to high-temperature under dynamic loading is required for the prediction of the damage extent during strain burst, and proper design as well as control of the underground rock structures. In this study, dynamic mode I fracture toughness tests are carried out on cracked chevron notched semicircular (CCNSCB) granite specimens to reveal the dynamic fracture characteristics of the brittle rock. For this purpose, a Split Hopkinson Pressure Bar (SHPB) apparatus is utilised to conduct the dynamic tests with various striker velocities on thermally degraded granite. The dynamic mechanical behaviour of granite after high-temperature treatment is examined and discussed. The dynamic fracture toughness is determined and compared for the specimens exposed to different temperatures at various dynamic impacts. The fracturing processes are recorded by a high-speed camera (HSC), and the crack propagation speeds are estimated by HSC image analysis. In addition, the dynamic fracture process and the coupled effects of temperature and loading rate on the dynamic fracture modes are identified by HSC image analysis. Energy partition characteristics in dynamic fracture of granite are quantitatively investigated.

Nov 29, 2022

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Dinuzzo P, Wychie J, Desoe C

The Selwyn Gold-Copper Mine is located 150 km southeast of Mount Isa within Proterozoic units of the Mount Isa inlier (Figure 1). Mineralization in the mine area is associated with strongly sheared ironstones and iron rich schists at the base of the mid- Proterozoic Staveley Formation. The ironstone horizons outcrop as a series of dominant ridges over a 10 km strike. Economic gold-copper mineralization has been defined in 4 separate zones within a 3.5 km length of the outcropping ridges. A current combined geological resource for the deposits is 5.3 million tonnes of 5.0 g/t Au and 2.02 Cu. Weathering of the deposits has resulted in a pronounced vertical zonation of mineralogy, especially copper, within the ore zones. This has produced 3 separate ore types which require different treatment techniques. The categorization is based on copper content and zones are termed leached (surface), oxide and sulfide. Ore removed from the pits will be mainly leached and oxidized with minor sulfide near the pits final depths, while the underground ore will be from the sulfide zone with minor oxide in some areas.

Jan 1, 1989

Western Australia has often been referred to as the fly-in, fly-out capital of the world. Fly-in, fly-out is a commonly used practice in Western Australia due to the geographic size and isolated location of the vast resource projects. In the State today, approximately half of all resource sector employees operate on a fly-in, fly-out basis, with a minority utilising drive-in, drive-out arrangements. fly-in, fly-out arrangements are generally beneficial from a sustainability perspective, delivering significant economic, social and environmental benefits to regional communities, the State and nation as a whole. Skills shortages and labour supply issues mean that the industry will be required to discover new ways of attracting and retaining employees, one of which is the adoption of fly-in, fly-out work journey arrangements. By 2015, the minerals sector in Australia will need to employ 70 000 more employees than it currently employs to achieve predicted increases in output. Of the 70 000 additional employees required, 42 000 will be required in Western Australia, almost 15 000 in Queensland and approximately 5000 in both New South Wales and South Australia. The fly-in, fly-out lifestyle as a preferred method of employment should be recognised as a valid lifestyle choice by all members of the community, offering a profound improvement in the quality of life for large numbers of employees and family members. It should be acknowledged that whilst fly-in, fly-out is a preferred option for many companies and their employees, individuals who make a choice to engage in fly-in, fly-out must balance the difficulties associated with the work û isolation and separation from family and friends û against the economic and lifestyle benefits that the work offers. This paper aims to illustrate the significant steps that the resources sector has taken to facilitate the fly-in, fly-out choice by ensuring that the commute option is a safe, attractive and manageable work journey arrangement.

Jan 1, 2008

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

The BHP Billiton Cannington Mine uses paste as the principal method of backfill. The paste consists of mine tailings and cement. The pastefill process at Cannington includes a surface plant where the thickened total tailings stream is filtered using two vacuum disc filters operating in parallel. The filter cake is mixed with Portland cement in a spiral mixer to produce a paste at a specified yield stress and cement content. The initial system design only required paste to be delivered under gravity. In July 2001, Cannington Mine expanded to 1.8 million tonnes per annum. In order to achieve this, production commenced on five new levels underground, 350 metres horizontally from the paste plant. Due to the high viscosity of paste, this distance was too far to transport by gravity. Traditionally, paste has been transported only short distances (50 m) using positive displacement pumps, with very limited success. At Cannington, a conveyor was installed which was designed to achieve zero spillage into the environment. This paper discusses the innovative design strategies used to attain zero harm on the environment whilst conveying a material, which is difficult to transport.

Jan 1, 2002

By A Sturgess, P McKenna, P D. Erskine, D Doley, V C. Glenn

For more than four decades, rehabilitated lands in the Bowen Basin have been planted with buffel grass (Cenchrus Ciliaris), which is often used to provide rapid, stabilising and erosion reducing cover to reshaped landforms (Erskine and Fletcher, 2013; Harwood, Hacker and Mott, 1999; Grigg, Shelton and Mullen, 2000; Naidu et al, 1997). Historically introduced to Central Queensland and encouraged by pastoralists in the early 1900s (Humphreys, 1967), the species has been extensively used by mine managers in seeding mixes (Coaldrake and Russell, 1970; Edye, 1975), and the invasive nature of the grass has led to the monodominance in rehabilitated areas of semi-arid Central Queensland. With 40 open cut coalmines in Central Queensland (Department of Natural Resources and Mines, 2015), a considerable amount of land is either disturbed mine footprint (156 200 ha) or rehabilitated (29 200 ha) (Dale, 2015), and the bulk of rehabilitation consists of relatively young (<30-year-old) developing ecosystems, with demonstrated biomass fuel loads up to 20 t/ha (Grigg, Shelton and Mullen, 2000).Uncontrolled fire poses a significant risk to rehabilitated landforms that are located in close proximity to mining infrastructure, neighbouring communities, open pits with exposed flammable coal seams and flammable stockpiled coal resource. Mine lease holders in Queensland have the added responsibility of managing and protecting any endangered regional ecosystem communities, and flora and fauna listed federally under the Environment Protection Biodiversity and Conservation Act 1999 or the State Vegetation Management Act 1999; as well as, any culturally significant sites such as scar trees or middens that are found on-site. Additionally, uncontrolled fire in rehabilitated landscapes poses a significant risk to mine site closure goals, with the potential to create altered states and stalled ecological trajectories (Grant, 2006). CITATION:McKenna, P, Glenn, V, Erskine, P D, Doley, D and Sturgess, A, 2016. Fire behaviour in buffel grass dominated mine site rehabilitation in Central Queensland, Australia, in Proceedings Life-of-Mine 2016 Conference , pp 158–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

In 1985 BMR assessed Australia's economic demonstrated resources of mineral sands as follows: rutile 8.0 Mt, ilmenite 41.4 Mt, zircon 11.5 Mt, and monazite 229 000 tonnes. These resources are located along the east coast of Australia, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth, WA. However, over 40% of Australia's rutile and zircon resources, particularly those on the east coast, are presently not available for mining because of environmental considerations. As well, east coast ilmenite has been considered unsuitable for use by sulphate route pigment producers because of its relatively high chrome content. World demonstrated resources of rutile and zircon are estimated by BMR as 29 Mt and 38 Mt respectively. Demonstrated resources of ilmenite amount to about 1 billion tonnes. These occur predominantly in hard rock deposits in Norway, Canada, USSR and China, as well as alluvial deposits in Australia, South Africa and India. Quantitative data for world monazite resources is sparse. However, world production of rare earth oxides is now mainly from bastnaesite, a hard rock resource. Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. With the expected increase in Australia's rate of output of these commodities, combined with restrictions on mining along parts of the east coast, its position could diminish substantially over the next 25 years.

Jan 1, 1986

By R R LARGE

In the past decade mineral deposit models have become an important tool for the exploration geoscientist. By combining genetic theories on the formation of particular deposit styles, with geological, geochemical and geophysical criteria relevant to ore location, it has been possible to more effectively focus exploration effort to the regions and local targets which have the best chance of success. However, such models have their limitations, and must be carefully and critically applied and continually updated as new technical and research information becomes available.

Jan 1, 1992

By J Skousen, C E. Zipper

"Prior to the 1950s in the USA, surface coalmines were generally left without any reclamation. As government regulations advanced, mine operators were required to backfill the area and plant grasses or trees. After the federal Surface Mining Control and Reclamation Act (SMCRA) was passed in 1977 in the USA, mine operators were required to conduct pre-mining analyses of the site and to designate a land use that could be achieved after the mining. Common post-mining land uses in the USA are: agricultural uses such as prime farmland reclamation with crops, hayland and pasture, and biofuel crops forestry wildlife habitat building site development.Provisions and regulations for each post-mining land use were developed and practices to achieve successful and sustainable land uses were established. Post-mining conditions should provide ecosystem services and produce lands capable of supporting societal needs in the future.CITATION:Skousen, J and Zipper, C?E,?2014. Post-mining land use options in the Appalachian coal mining region of the USA, in Proceedings Life-of-Mine 2014, pp 153–164 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By Blockley J. G, Laeter J. R

The history of the Ph-Cu-Zn mineralisation in the orthampton Block of Western Australia has been further investigated. It was hoped that (1) Rh-Sr studies on partially-remelled granulites, wall-rocks to the dolerite dykes, should date the dolerite intrusion, (2) Rh-Sr data on hydrothermally-altered dolerite should date the sulphide mineralisation, (3) Pb model ages on the galenas might provide an independent dating of the mineralisation, in addition to any geochemical information that might be derived. Only the second dating aim was fulfilled, but the Pb isotope data, when combined with the Rh-Sr data, have permitted deductions about U, Th and Pb abundance changes during the regional metamorphism, and about a possible source of the ore Pb. In detail the following has been found. (1) The partially-remelted granulitic wall rocks yield a scattered whole-rock Rh-Sr isochron which seems not to have been reset by the dyke intrusion (age 1037 ± 146 Ma, with initial Sr ratio 0.7171 ± 0·0054, MSWD = 111). This date agrees well with that reported previously for granulites from another locality; together theyestablish the time the metamorphic period closed. (2) The hydrothermally-altered dolerites yield a Rh-Sr whole-rock date 434 ± 16 Ma, with initial Sr ratio 0.7072 ± 0·0029 and MSWD = 31, taken as referring to the time of Ph-Zn mineralisation. This contrasts with a report of much older palaeomagnetic and K-Ar datings of the dolerite (not less than 550 Ma, possibly older) and suggests that neither the dolerites nor their heat have had any connection with the mobilisation of the Pbscavenging solutions. (3) The Pb isotope ratios of galenas from the ores yield a well-correlated regression which is not amenable to any of the model-age calculations. (4) The Pb-isotopic trends negate any genetic connection between dolerite and mineralisation, but the country-rock granulites could be the Pb source. (5) Combination of the Rh-Sr dates and the Pb data in a "simultaneous isochrons" construct permits the inference of major losses from the system during the regional metamorphism, in the order U>Pb>Th, with substantial homogenisation of the remaining Pb. This left a wide range in local UlPb and Th/U among the source rocks which eventually were scavenged by the mineralising solutions. (6) These geochemical deductions are shown to be compatible with previously-published information on the abundance ofU and Th in the Northampton Block granulites, which are thus seen to be credible as source rocks for the ore lead.

Jan 1, 1985

By G R. Hancock

A common and cost-effective method for post-mining landscapes is to construct linear hillslopes with a break in the hillslope at appropriate distances to reduce hillslope length and resultant erosion risk (Figure 1). The break in slope occurs at a point that has been found by local experience to be appropriate for the materials and climate. Further enhancement of the linear hillslope may be assisted by surface treatment such as ripping (Saynor, Lowry and Boyden, 2019) (Figure 1). Firstly, ripping introduces surface roughness which breaks up flow paths reducing flow velocity thereby reducing erosion potential. The depression produced by the ripping acts as a trap which captures water, sediment and organic matter

Aug 2, 2023

By D J. Black

The process of excavating and mining coal causes fractures in the overlying and underlying strata. The fractures provide pathways for gas released from coal seams and other gas-bearing strata to flow into the mine workings. Coal seam gas typically contains high concentrations of methane with lesser concentrations of carbon dioxide. Low concentrations of other gases such as nitrogen, hydrogen sulfide and ethane may also be present in some coal seams. In certain geological settings, particularly in close proximity to geological structures, such as faults and dykes, the concentration of gases contained in a coal seam can vary significantly between methane-rich to carbon dioxide-rich.In mine design and planning it is vital that mining engineers gather sufficient information to accurately determine the content and composition of the gas present in the coal seam and develop an understanding of changes in these parameters within the planned mining area.The longwall method of mining coal causes fracturing of the overlying and underlying strata behind the retreating longwall face. Where coal seams and other gas-bearing strata are present within the caving zone, gas will be released from the strata leading to contamination of the mine workings. If the rate of gas emission exceeds the diluting capacity of the mine ventilation, the concentration of gas in the mine may exceed the statutory limit, resulting in production delays and potentially unsafe conditions.CITATION:Black, D J, 2016. Planning effective management of gas emissions in an underground coalmine, in Proceedings Life-of-Mine 2016 Conference, pp 44–47 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Kanchibolta S. S, Brunton I, Tapia-Vergara F

The Split digital image processing system has been implemented in three Australian mines for analysing the size distribution of rocks from the images taken from muckpiles, conveyor belts and tipping trucks. This paper presents an overview of t

Jan 1, 1998

The behavior of a curved wall under earth pressures for a horseshoe shaped tunnel lining is considered to be closely related to the beha vior of a vertical beam with variable flexural sti-"ness on an elastic foundation. In stress analysis an approximate method which divides the axis of the tunnel lining into small finite lengths and replaces the integrals by summation is usually adopted. this method is extremely complicated and tedious. However the variations of the moment of inertia from point to point along the wall axis can be expressed by a power function inversely .eith the distance from the ll )ottom and the analytical method can still used. The equations for the calculation of deflection, rotation, bending moment, shearing urce, and soil reaction of the curved wall are derived in nondimensional forms in this paper.

Jan 1, 1987

By Torrance AC

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation veloci- ties of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation meas- urement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 150g. owever, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1988

By T P. Tafirenyika, K C. Corin, C T. O’Connor

There is a growing demand for copper driven by its applications in renewable energy and electric vehicles. Sulfide ores are an important source of copper. Flotation is a critical front-end process used to remove gangue minerals and concentrate the copper minerals. The electrochemical activity of sulfide minerals contributes to their overall activity in the flotation pulp. The mineral rest potential dictates how collectors interact with the mineral surface, and hence ultimately on the flotation response. Dissolved oxygen, (DO), pH, redox potential (Eh) and water composition and ionic strength are also significant in controlling flotation performance. The aim of this investigation was to determine the influence of the electrochemical environment both during milling and flotation on the flotation behaviour of bornite and chalcocite. For this investigation, the interactions of collector with bornite and chalcocite were studied using synthetic plant water (SPW1) and deionised water (DIW) at 5 different pH levels. Sodium isobutyl xanthate (SIBX) was used both in microflotation, collector adsorption and zeta potential tests.

Aug 24, 2022