Search Documents

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By J. Patterson

"Acid Mine Drainage (A.M.D.) formed from oxidation of disposed pyritic wastes presents a potential pollution hazard for Equity Silver Mines Limited and the mining industry in general. Failure to collect and treat these acidic effluents can eventually affect the quality of receiving streams and endanger aquatic life forms. Treatment and discharge of A.M.D. to the receiving environment must comply with stringent anti-pollution laws.Wastes mined at Equity Silver Mines Ltd. are predominantly acid generating and must be handled according to a materials management plan to minimize impact on the environment. Effluent collection and treatment facilities have been constructed to address the short term environmental concerns with reclamation and research programs being developed to address and monitor abatement measures for control over the long term.The purpose of this paper will be to offer a brief overview of these measures. Key topics for discussion will be: kinetics of Acid Mine Drainage, acid generating potential, water treatment and sludge handling, special wastes, waste dump construction, waste rock amendments, bacteriocide research, simulations, and reclamation measures. Programs designed to evaluate impact on the receiving environment, although they form an extensive part of the program, will not be discussed in this paper.INTRODUCTIONEquity Silver Mines Limited is located in the Central Interior of British Columbia, within the Omineca Division, 35 kilometers southeast of Houston Mining and approximately 575 kilometers by air north-northeast ofVancouver (Figure 1).The deposit consists of three economic mineralized zones: The Southern Tail, Main and Waterline Zones. Mining of the Southern Tail commenced in April, 1980 and was completed in the first quarter of 1984. Main Zone production was initiated during the last quarter of 1983 and the Waterline Zone remains undeveloped to-date. Remaining reserves are in the order of four years contingent on favourable metal prices. The three deposits (Figure 2) occur within a window of interbedded volcanic and minor sedimentary rocks. The older volcanic sequence is bounded on the west by a small granite-like stock and on the east by a gabbro-monzonite complex. All are overlain by a series of younger lava flows."

Jan 1, 1988

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By J. M. Wolverton

CONSIDERABLE interest has always been taken in Safety-First and First Aid at the Sullivan mine. Even during the early days of development, Safety-First committees periodically held meetings, while lectures in first aid were given to any employees interested in the work. In 1929, a Safety Department was organized, and all accident-prevention and first-aid work was put in charge of a full-time Safety Engineer. An extensive programme has gradually been developed, the value of which can best be indicated by the reduction of the accident rate from 18.4 shifts lost per 1,000 shifts worked for non-fatal accidents and two fatalities for 1927, to 3.24 shifts lost per 1,000 shifts worked and no fatalities for 1936. SUPERVISION All work connected with accident prevention or first aid is under the jurisdiction of a central committee, known as the Accident Prevention Committee, which meets regularly once a month. It consists of all superintendents, department heads, foremen, and shift bosses, and is presided over by the Safety Engineer. At these meetings, the accident records of the previous month are reviewed and all accidents carefully analyzed and discussed. All proposed changes in the safety rules or in the accident tprevention programme are taken up and passed upon. Complaints or suggestions from the Safety-First Committee and the Employees Co-operative Committee, dealing with safety, are discussed and passed upon or a subcommittee is appointed to investigate and take any action found advisable. The question of underground ventilation and dust control, which recently has become a very important problem, always receives considerable attention.

Jan 1, 1937

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By C. O. Aksoy

There is a long history of coal production in Turkey with electric energy generated from power plants since the 1950s. However, the cost of power generation is high. Therefore, it has become necessary to find a means of decreasing production costs to become more competitive in a global market. This paper attempts to economically minimize the overall operating costs of a dragline-shovel-truck system applied at an open pit mine that has fed the Yatagan power plant since 1979, lowering the lignite production cost, and indirectly, the overall electricity generation unit cost. Systems currently in place, as a result of former optimization studies, are time-consuming and expensive to re-implement to comply with today’s very different geometric and economic conditions affecting mining operations. In such cases, rather than re-optimization, it is more viable to identify the parameters that affect the minimum unit cost, via a cost minimization study, allowing present mine equipment to be utilized more efficiently. Unit cost minimization analyses are subject to the capacity of the pool of mining equipment available, combined with the mining block geometry from pre-stripping onwards. In this overall unit cost minimization study, P&H shovels and CAT 777 trucks with capacities of 15 yd3 and 77 tons, respectively, were used in truck-shovel pre-stripping operations. A 65 yd3 Marion 8050 dragline was used to expose the overburden immediately over the coal seam. Pre-stripping bench heights varied from 8 m to 20 m and dragline bench heights from 20 m and 25 m were evaluated to minimize the unit cost of field operations. Total overburden extended to a depth of 60 m (35 m to 40 m for pre-stripping). Minimization analyses performed on the pre-stripping truck-shovel operation, prior to dragline operations, determined that the shovel bench height should be 15 m requiring a dragline bench height of 25 m.

Jan 1, 2005

By R. H. Fett

T HE APPROACH to maintenance must always be ?completely positive: there must be no question of putting off difficult problems until it is more convenient to tackle them. By this it is meant that a piece of machinery or equipment which, by experience, is known to be due for a check should not, merely because it appears to be operating satisfactorily, be left until it reaches a critical .condition and breaks down. The mentality of the Maintenance Manager must be completely orderly and methodical and he should, in fact, possess a ledger-book mind, having a debit and credit outlook. The debit side would be that applying to time out of service, cost in wages, material, personnel involved, etc., and the credit side that relating to continuous operational time of the locomotive and therefore to the ultimate benefit of the mine and the personnel who work there. The Maintenance Manager is not concerned with design problems, and although he and the personnel under his jurisdiction are not engaged in productive work, he and his staff do, nevertheless, add greatly to or detract from the overall efficiency of the organization. Provided the machinery placed in his care is good to start with, he must take the best steps he possibly can to keep it running. However, he may, on occasion, be forced to improvise and this is where the ingenuity of a clever man rises to the occasion.

Jan 1, 1956

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

By D. E. Smith, M. K. Murthy

"The commercial potential of a silica-kaolin deposit that occurs on the banks of and close to the Missinaibi River in the District of Cochrane, Ontario, is under evaluation by Algocen Mines Limited. The geological features of the deposit, as well as its probable origin, are described. Mineralogical analysis of the deposit samples indicates that the principal minerals are quartz and kaolinite clay; it is estimated that about 20 per cent of the deposit is kaolin clay. The impurity minerals present are: a slightly magnetic Fe-Ti oxide mineral, goethite, muscovite mica, tour-maline, staurolite, anatase and zircon. Laboratory research studies are in progress to develop and evaluate suit-able methods for the separation of silica sand from kaolin. Results to date indicate that good-quality silica sand with an Fe,03 content in the range of 0.012 to 0.025 per cent can be produced. It appears that the clay portion can also be beneficiated to yield products meeting commercial requirements. It has been possible to beneficiate a portion of theetlay to obtain the particle size distribution now specified by industry. However, research is continuing to develop suitable separation and beneficiation methods which can produce kaolin clay meeting all the commercial requirements."

Jan 1, 1970

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By A. H. Marquis

Since the start-up of its first Direct Reduction Module in April 1973, S1DBEC has produced over 2 million tons of prereduced iron. During this period, SIDBEC has acquired comprehensive experience in the operation of the direct reduction process and at the same time has learned to recognize the characteristics that the oxide should have to constitute an adequate feed for the process. A comparison is made as to the design and operation of the two direct reduction units now operating at Contrecoeur, Que. A description is given of a method of evaluation of a direct reduction unit, which takes into account the main process variable sand which permits comparison ofthe results on a daily basis. The paper defines the characteristics that the iron oxide and the prereduced iron pellets must have to meet the specific requirements of the direct reduction and the electric arc furnace processes. A simple model makes possible a rapid evaluation of the technical and economic effect related to the use of a given raw material. Finally, the paper outlines the advantages of prereduced iron in the steelmaking process and on the quality of the steel products.

Jan 1, 1979