Search Documents

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By Karl J. C. Harries

"11.1. INTRODUCTIONA royalty is the most common form of interest retained by an owner who is disposing of his property or by a joint venturer who ceases, voluntarily or otherwise, to participate in the joint venture.1 Rarely does a non-participating party have a direct interest in the property and/or assets of a project, except during the period when a non-participating joint venturer may be having his interest diluted.2 In fact, it is most unwise to permit a non-participating party to have such an interest. It may give rise to significant problems that could prevent or substantially delay the development of an orebody and require a considerable amount of time, effort, and money to correct.3In negotiating a royalty, it is important to be aware that there is no law or convention that says, “You just don’t do that in a royalty agreement.” As with any agreement, inventiveness and flexibility on the part of the negotiator are not just assets, but virtual necessities. It is also for this reason that it is essential to read the royalty provisions, particularly the definitions, fully and carefully, especially if you are the recipient. On the other hand, if your inventiveness and flexibility cause your accountant to question the advisability of one of your ideas, pay close attention to him.4 He will, no doubt, have had experience with many royalties, and no competent professional adviser disparages a client’s ideas without good reason. Besides, he will probably be the person who will be determining the royalty or certifying the determination of it. At the very least, he will be auditing your general financial statements, which must, of course, reflect the royalty determination. Heeding his advice not only may make the determination easier but also will probably save you money in professional fees later on. Nevertheless, do not simply accept his comments or recommendations without understanding what they mean, why they have been made with respect to your royalty agreement (sometimes professionals have comments that they make as a matter of course and, even though they may be valid, you should require them to be justified to you), and how they will affect your royalty determination.It is surprising how many corporate payors insist that their standard royalty provisions5 be used as a matter of policy, thereby effectively tying the negotiator’s hands. It is even more surprising, and to professional advisers frightening, how many of the senior employees who insist that such a policy be adhered to, virtually without variation, do not know what is in the standard provisions and would be hard-pressed to explain them to a property owner. If standard provisions are appropriate, by all means use them, but do allow experienced and sensible negotiators some flexibility and make sure that everyone within the corporation who may have to use such provisions – negotiator and supervisor alike – knows what they contain and why they are as they are. For example, there are often good and convincing reasons to describe a deduction in a certain way or to include a certain specific type of deduction. On the other hand, quite often the answer to the question “why?” is that “it has always been there”; this is, or should be, an unacceptable answer. In any event, if you, as the negotiator, appear to know what you are talking about, are familiar and comfortable with your royalty provisions, and are backed up by your boss with the same words or reasoning, a property owner cannot help but be satisfied that you are knowledgeable, even if he still does not agree with your provisions. Finally, if you do use standard provisions, make sure that they are reviewed and updated regularly."

Jan 1, 2003

By L. M. Southwick

"The history of extractive metallurgy is replete with examples of commercializing new processing technologies. The successes are widely reported, but failures seldom are. This is unfortunate, for usually we can learn more specifics on how to succeed in technology development by studying and thoroughly understanding their failures. Frequently one encounters a red herring that caused the whole effort to fail. A thorough and objective due diligence up front would have identified those red herrings and prevented the pursuit of a bad idea and the resulting destruction of capital. Due diligent analyzes performed before construction of three such bad ideas will be discussed. One is an EAF dust process, which pursued the red herrings of a poor understanding of the business, a naïve view of past experience, and false confidence in the technology. Another will examine the effort to commercialize a new pressure copper leach process that followed the red herrings of inadequate testing of the raw material, application of processing conditions that were inherently unsafe, and an improper assessment of the inherent advantages of past developments. The last is an alternative iron-making process, where the red herrings were incomplete and superficial assessment of prior pilot plant and demonstration plant tests, an assumption that the commercialization model of “build it and we will make it run” was viable, and a technology whose technical fatal flaws had already been identified. Unfortunately, capital destruction often also closes the window to more intelligent pursuit of technology development. TECHNOLOGY COMMERCIALIZATIONThe development and commercialization of new technology is a vital part of keeping industry profitable, able to deal with new sorts of feed stocks and current with economic, product, operational and environmental requirements. This is a difficult task in the best of times, and can be compounded when the developers become enamored of a particularly favorable characteristic of the project or of the product. These “red herrings” divert project focus away from the arduous path to success and, in the end, result in project failure."

Jan 1, 2012

By M. Pearson, W. Bristowe, A. Hanson

"There's no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors' experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

By L. Larson

Rock samples were taken, away from zones of mineralization , from seven sections of five rhyolitic zones as define d by Spence (l967) in the Noranda area. The purpose of the investigation was to test whether there were intrinsic differences between the zones which would differentiate between non-productive zones and productive zones. For the elements sought (major elements, Cu , Pb , Zn and S) , no clear chemical difference between the zones was found. Thus, identification of a favour able zone from the over -all composition of the zone does not appear promising. Within sampled sections, there is no clear gradual compositional change up through the sections. A capping of highly siliceous massive rhyolite is present in five of the sections sampled. A layer of relatively basic material occurs near the base of individual units. The third (mine zone) and later zones contain abundant pyroclastic material, where as the non-productive zones do not.

Jan 1, 1977

By S. Junnikkala, K. Föhr

"Experiments were performed with plant feeds with a continuous 1,8 m3 cell at Pyhasalmi mine with Cu flotation feed in order to test the applicability of the bubble surface area flux as an indicator of the flotation rate constant. It was found that bubble surface area flux could not predict the rate constants of coarse Cu containing fractions. In the middle size fraction, the correlation coefficient in the rate coefficient estimation was higher but not statistically significant. Only the fine fraction showed a linear relationship with a moderate correlation coefficient.The bubble surface area flux was shown not to be a function of the impeller velocity above a threshold value. The flux was an almost linear function of the superficial gas rate enabling to use the superficial gas rate instead of flux if the operation of an existing cell is to be estimated.INTRODUCTIONBubble area flux seems to offer a simple way of modeling flotation. It relates the flotation rate constant with the bubble surface area flux by a simple linear equation. Due to this, there has been a considerable interest in using the bubble area flux for flotation computations. It has even caused claims that a cell producing a high bubble surface area flux automatically produces a high rate constant and therefore a high recovery.This paper discusses some of the assumptions of the relationship and gives some plant results during two sampling campaigns.The bubble surface area flux s b is describing the area of bubbles available for flotation in a cell per unit area. The bubble surface area flux is related to the superficial gas rate J, by the Sauter mean diameter as follows"

Jan 1, 2001

By J. -C. Sztuke, M. Cao

ABSTRACT Wash water and polyethylene oxide (PEO) were used in the flotation of quartz and coal. Wash water decreased entrainment of –15 µm quartz. The optimum superficial wash water rate was 0.05 cm/s. PEO also lowered entrainment. The combination of wash water and PEO led to a slight further reduction in entrainment. For 1:1 mixtures of –15 µm quartz and –300 µm oxidized coal, the combined use of wash water (0.05 cm/s) and PEO increased the separation efficiency from approximately 30% to > 70%, whereas wash water alone at 0.05 cm/s did not lead to a discernible increase.

Jan 1, 2014

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By H. A. Dakin

"An introduction to the metallurgical requirements of the Flin Flon concentrator reveals the magnitude of ore blending which is required in its operation of three flotation circuits. The resulting variability in flotation heads which has in-creased the separations complexity justified the development of an on-line analysis system.This paper provides a summary of the development and operation of that system. Particular attention is devoted to the problems encountered and where possible their solutions; as the requirements of accurate information and minimum downtime of the sampling system and x-ray analyzer are considered essential. The addition of a recess central computer has provided information in a more easily understood form and as well has allowed the start of automatic reagent control.An indication of the on-line analysis system's value to the concentrators' operation is provided by an examination of the plant in metallurgical data and reagent costs in previous years.The metallurgical plants of Hudson Bay Mining and Smelting lie adjacent to the city of Flin Flon on the Manitoba-Saskatchewan boundary. Plant operations commenced in 1930 treating copper-zinc ore from the local mine. In recent years ore bodies near Flin Flon and in the Snow Lake area, about seventy-five miles east, have been brought into production.By the beginning of 1973 the number of producing mines had increased to nine; with all the ore being handled by the Flin Flon concentrator. Figure l, showing mine ore assays during 1973 indicates the variation in metal content possible."

Jan 1, 1974

By D. Schleiss

Reduced access to knowledgeable workers is creating challenges for operations. We are doing more 4D Operations - dirty, dull, dangerous, and distant. Personnel costs in these environments are high, and it is not always possible to get the people where you need them. Integrated Operations is a strategy to integrate people, process, and technology for faster and better decision making. Adopting an integrated operations approach can help to relocate personnel, improve collaboration, and align objectives to deliver reduced costs and improved performance. In this paper, the authors will highlight the required infrastructure to enable an Integrated Operations platform. Key decision points for enabling this technology for both Greenfield projects and existing mines will be discussed. Furthermore, the benefits and improved return on investment that result from deployment of an Integrated Operations strategy will be presented.

Jan 1, 2014

By D. Van Tonder, C. Edwards

ABSTRACT Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium-bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares seven of these options on the basis of typical capital and operating costs for the solvent extraction circuit and downstream uranium processing and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.

Jan 1, 2013

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By N. E. Izatt

Molecular recognition technology (MRT) has a wide range of applications in the hydrometallurgical and chemical processing industries for the selective removal of iron as well as various other impurities from a variety of streams, including aqueous solutions through a wide pH range, as well as organic solutions. An example of a commercial application is provided for the removal of iron from an aluminum chlorohydrate stream. In this example, MRT has a selectivity for iron relative to aluminum which is significantly higher than that of ion exchange resins. A discussion of MRT capabilities for other impurities and streams is also provided.

Jan 1, 2006

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By D D. Deacon

A brief description is given of the requirements which No. 4 Shaft has been designed to meet and of the methods by which two-stage winding of rock has been accommodated in a single shaft sunk to a depth of 7,421 ft. This is followed by a consideration of the factors which led to the decision to sink the shaft as rapidly as possible. Introduction T HE No. 4 Shaft of Hartebeest-fontein Gold Mining Company, Ltd., has been sited to serve the deep southern area of the mine, some 1,500 claims in extent, between the elevations of 6,250 and 7,300 ft. below surface. From this area, some two-thirds of the mine production will ultimately be obtained. Above the 6,-250-ft. elevation, an existing shaft hoisting system, situated adjacent to the reduction plant, is of adequate capacity to cater for all ore hoisted to surface for milling. No. 4 Shaft will therefore be required to provide downcast ventilation of 1,000,000 c.f.m., together with surface hoisting facilities for men, material and development rock and underground hoisting

Jan 1, 1965