Search Documents

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By R. K. Borden

Rio Tinto is committed to proactive mineral waste and acid rock drainage management. Corporate requirements are closely aligned with the GARD Guide principles of early geochemical characterization and prediction followed by selection and implementation of management strategies to prevent or minimize ARD. Each operation is required to design and implement an ARD and Mineral Waste Management Plan. Successful implementation of the plan requires commitment at all levels of the company, from senior management, to geologists, mine planners, environmental staff and equipment operators. Examples of the successful integration of ARD management strategies into mine operations are cited from several mines.

Jan 1, 2011

By Y. Okita

The Goro Nickel Process, developed over a ten-year period, uses a number of novel processing steps and treats two ore types, limonite and saprolite, together. Nickel and cobalt are solubilized using a 270°C pressure acid leach in sulphuric acid, which rejects the bulk of the Fe into the leach residue as hematite particles. The leach liquor, after CCD, is aerated to oxidize any ferrous iron to the ferric form and is neutralized with limestone to precipitate iron as hydroxides together with gypsum from the neutralization of the free acid. Further neutralization with lime, together with steps to remove suspended solids, reduces the iron to trace concentrations. Nickel and cobalt are directly recovered from the low-iron leach solution by primary solvent extraction using Cyanex 301® (SXl) in a high-strength hydrochloric acid solution. Nickel is subsequently separated from cobalt in a secondary solvent extraction circuit using tri-isooctylamine. A granular nickel oxide is made by pyrohydrolysis, and this allows the recycling of hydrochloric acid to SXl. The process is currently being commercialized to produce approximately 60,000 t/y of nickel as nickel oxide granules and approximately 5,400 t/y of cobalt as cobalt carbonate. This paper describes the process development to control the Fe concentration in the SX1 feed solution.

Jan 1, 2006

By R. K. Collings

The annual production of mineral and mineral-based wastes in Canada is conservatively estimated to be 400 million tons. Over 90 per cent of this amount is waste rock or mill tailings from the mining and mineral processing industry. The remainder are slags and ashes from the metallurgical industry, and sludges from the chemical industry. Because of impurity content, remote location, or both, most wastes have limited usefulness and, indeed, are a liability in that they must be transported to waste disposal sites and contained therein. Certain mineral wastes do, however, have potential value. Some contain small percentages of metals that may be economically recoverable with price increases; others consist of mineral material that may be used for such purposes as road base, construction aggregate, railroad ballast, and in the manufacture of bricks or blocks. Increased interest has been shown in mineral wastes in recent years. This paper reviews the types of mineral wastes available in Canada, briefly describes a number that have potential value, and notes possible uses and related research by CANMET and other organizations.

Jan 1, 1978

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By D. J. McCulla

Mineral development and utilization affect the health of the economy and the pattern of long-term development throughout Canada. There are many diverse opinions on the contribution of minerals to the economy, but there is a dearth of adequate quantitative information. This paper discusses some recent research and provides some new information.

Jan 1, 1977

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By Paul E. Lamoureux

Introduction The Author As the pail of smoke and wartime destruction gradually rises from the surface of the earth, from all countries, statesmen assemble to discuss and prepare pacts and treaties which are designed to, once more, bring people of all nations to understand each other and live in harmony. Scientists and engineers throughout the world are also undergoing a drastic reconversion in their ideas and objectives. No longer do they think only in terms of destruction and twist their brains to develop more devastating weapons or to surpass production records of war machinery. They have turned their eyes and ambitions to more pleasant tasks and are taking stock of wartime developments in materials, fabricating procedures, and equipment, many of which had been carefully shrouded with a veil of secrecy, and are applying their new knowledge to the fabrication or improvement of the tools of peace. The next few years will see the gradual elimination of scores of substitutes and makeshifts, expedients which the constantly changing law of supply and demand' under wartime stress necessitated. The universal search for satisfactory substitutes, however, has resulted in a general awakening of plant engineers to the possibilities of materials with which they were relatively inexperienced, with the result that, in many instances, what was considered a substitution at the outset turned out to be more satisfactory than the original material, and, in reality, can be considered a worthwhile development. Not only have materials been explored, but existing fabricating processes have been reviewed, and others, built around the properties and characteristics of new materials, created.

Jan 1, 1947

By François Robert, Steve Green, Tyson Birkett, Dan Richardson

Abstract -Detailed sampling using a portable diamond drill, and interlaboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d'Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or Jess. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d'Or area.

Jan 1, 1992

By D. G. Klaren, E. F. de Boer

Self-cleaning fluidized bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve any problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials have been used. In addition to the mitigation of fouling effects, a number of other significant benefits for slurry heating are afforded by the mode of operation of the self-cleaning fluidized bed heat exchangers. Increased turbulence at the slurry/tube interface is imparted by the action of the fluidised particles, resulting in very high heat transfers at relatively low liquid velocities. Furthermore, given the thixotropic nature of most process slurries, the action of the fluidised particles imparts additional shear to the process slurry, resulting in shear thinning effects with a consequent reduction in pressure drop and enhancement of heat transfer across the heat exchanger. The benefits provided by the self-cleaning fluidized bed heat exchanger make it the ideal option for the indirect heating of laterite nickel slurry for High-Pressure-Acid-Leach (HPAL) plants. This article explains the principle and application of the self-cleaning fluidized bed heat exchanger technology for the processing of laterite nickel and cobalt slurries in HPAL plants. It also presents an elegant method to revamp existing direct heated laterite nickel and cobalt processing plants into an indirect heated configuration employing self-cleaning fluidized bed heat exchangers.

Jan 1, 2004

By H. Mindivan

In the present study, the feasibility of recycling AA6061 Al alloy chips by a combination of ciyomilling, cold compaction and hot extrusion processes was investigated. Furthermore, the effect of Al powder addition to the recycled Al alloys chips on the mechanical properties was investigated. The characterization of recycled Al alloys was made by structural examination and mechanical tests (hardness, compression and dry sliding wear tests). The results indicated that by increasing wt. % of Al powder added to the recycled Al alloy chips the studied properties (the density, hardness, compressive strength and wear resistance) increased due to reduction of porosity in the recycled Al alloys.

Jan 1, 2011

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By P. A. Distin, Jr. da Silva

The history of commercial processes for zirconium/hafnium production and separation is reviewed. A new technology is then proposed as a potential alternative for zirconium/ hafnium separation in a simpler, cleaner way than achieved with current processes. Primary sources of zirconium always contain small amounts of hafnium that must be removed during production of zirconium metal for nuclear applications. This separation is usually carried out by a solvent extraction process, developed in the 1950s, that selectively extracts hafnium, as a thiocyanate complex, using methyl isobutyl ketone (MIBK). Environmental problems inherent to this process are the high aqueous solubility and low flash point of MIBK, and possible gaseous contaminants formation generated by the decomposition of the thiocyanic complexes in hydrochloric acid medium (H2S, HCN, mercaptan’s formation). The present work shows how these problems could be avoided by using organophosphorous extractants that were unavailable when the MIBK process was developed.

Jan 1, 1998

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By G. W. Smith

"The adsorption of dehydroabietylamine acetate on quartz, hematite, rutile and baddeleyite has been deter-mined for concentrations ranging from 0.3 to 5,600 µ. moles/I and for pH values ranging from 2.5 to 10.5.The surface tension, UV and IR spectra, equivalent conductance and ion concentrations for dehydroabiety lamine acetate solutions have been determined.Contact-angle and flotability studies have established that good collection may be obtained with this amine but that selectivity depends on the suitable use of depressants for some of the minerals."

Jan 1, 1971

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976