Search Documents

By J. E. Hawley

"The Aldermac copper deposit is in Beauchastel township, Abitibi county, Quebec. It lies about 11 miles west of Noranda. It has been described by Cooke, James, and Mawdsley(2) and by Bruce(3) and has been mapped in detail by W. Samuel and the late K. W. Fritzsche, former Mine Geologist, and by J . E. Gill and A. R. Byers, so that most of the particulars contained in the description that follows are largely the result of the work of others than the writer, whose connection with the deposit, in a consulting capacity, extended over the last 5 years of the life of the mine.According to A. V. Corlett, former Mine Manager, the property was staked during the early winter months of 1923 because of its location adjacent to the syenite intrusive that had been mapped by Cooke near the height-of-land in this township. An examination by Mr. Corlett in 1924 revealed mineralized zones to the north of MacKay lake, and in the vicinity of these K. W. Fritzsche, by dip needle and trenching, discovered the No. 1 and No. 2 deposits, which were both too small and too low grade for exploitation. During the winter of 1925, A. A. MacKay, with a dip needle, picked up a magnetic 'anomaly' in a drift-covered area about 600 feet to the north of previous workings. Trenching here revealed only a narrow zone of mineralization of little consequence, but, farther east, MacKay discovered a more pronounced 'anomaly' over what later drilling and underground work proved to be ore of commercial grade (No. 3 and No. 4 orebodies)."

Jan 1, 1954

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By G. C. Nowlan, A. Illis, H. J. Koehler

At its iron ore recovery plant at Copper Cliff, INCO produces about 17 million pounds per year of a pure, acid-soluble, dense nickel oxide from nickeliferous pyrrhotite. The process used is also applicable to a broad range of ammoniacal nickel-bearing streams. The product has been widely accepted by the chemical, ceramic and electronic industries.

Jan 1, 1970

By C. Holmes, T. Holmes

Engineered-in material handling problems are responsible for significant unrealized value in mineral processing plants. At the root, is a lack of awareness and understanding of bulk material handling science and how important it is, especially in early design stages. Mineral processes add value to mined raw feedstock through physical and chemical transformations in unit operations, but only if the material can flow through them. Essentially, each unit operation receives a unique feedstock and produces a unique product to be collected, transported, and fed into the next unit operation. Such material-handling systems can only be expected to achieve design throughput if the system equipment is designed to the materials’ characteristics, over their full range of conditions. This requires quantification of flow properties to support the necessary customized equipment designs. Too often, assumptions or “library values” of a material’s properties are used as the basis for flow modelling and conceptual, and sometimes even detailed, design. This is especially true for hazardous materials like uranium ore, for which the additional precautions, costs, and time necessary for safe handling are often used to rationalize postponing or even bypassing testing. The surprises that often transpire in the wake of insufficient material handling consideration can have acute and costly effects. Fortunately, there is a better way.

Jan 1, 2020

By W. B. Gallup

"The Athabasca Bituminous Sands have been subject to sporadic investigations since the beginning of the century. It is probable, however, that much of what has been learned and achieved concerning the deposit has been accomplished in the last few years.Current exploratory techniques, generally speaking, involve a moderate amount of coring. Electrologs and often radioactive logs are run on most holes and certain types of these archieved excellent qualitative analysis when backed up by some core analysis for calibration. Exploration - is moving back from the river and consequently a permanent network of access roads has been developed within the last few years. Most of the operations take place in the winter time. There are about 90 permit holders at the present time.Some exploratory techniques are set up to go into recovery experiments where rich tar beds are found. It is probable that in the final analysis there will be several successful methods of extraction and that both mining and various in situ techniques will be applicable depending upon the problem locally."

Jan 1, 1960

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By P. Moreno

ABSTRACT: The Maras salt terraces, located between Cuzco and Urubamba in the Andes (southern Peru), are living examples of traditional Incan salt production, where present-day artisanal miners produce salt from shallow pans by solar evaporation. In these terraces, natural spring water, eight to nine times saltier than seawater, is used to produce the salt. The field observations and chemical analyses show that the poorly crystalline traditional salt is finer in particle size and contains impurities such as dolomite and gypsum. These differences are the result of shallow pond depth, contamination from wall erosion, and the nonsequential mode of salt crystallization.

Jan 1, 2011

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By H. Hamza

Efficient and effective management of extraction process tailings is an essential ingredient for the continued success and development of Alberta's vast oil sands resources. Open-pit oil sands operations north of Fort McMurray recover bitumen from flotation circuits. Process tailings are managed in carefully engineered and monitored external tailings management facilities and in below-grade mine pits. In order to support reduction of production costs and improve upon established tailings management practices, CANMET has been working with the oil sands industry in a collaborative framework to assess the potential to integrate thickened tailings into oil sands extraction process flowsheets. Albian Sands has commercialized the process while others, including Syncrude Canada Ltd., continue to evaluate the suitability of the process for their operations. This paper provides an update on R&D work undertaken in recent years to assess and develop the potential of thickened tailings technology for the open-pit oil sands operators of northern Alberta. The aim of this work was to explore opportunities to optimize process efficiency and environmental sustainability by improving water and energy conservation and develop more alternatives for tailings management and reclamation.

Jan 1, 2004

By Staff, G. M. Hogg

"The eastern portion of the Late Precambrian geosynclinal structure known as the Labrador Trough comprises a 16,000-square-mile sulphide-bearing belt of good potential as a base metal exploration area. Hollinger and Hanna mining interests have carried on exploration in the region since 1953, with encouraging results. This program has been considerable in terms of both effort and expenditure, and has resulted in an apparently successful primary evaluation of the entire belt.Much detailed work remains to be done in the area. Exploration to date has been largely of a reconnaissance nature, employing various methods in common use in Canada today. In the course of this work, several deposits of promise, containing near-economic quantities of copper, zinc, nickel and other metals, have been located. A broad classification of these deposits is proposed.Exploration in the sulphide belt was started on the basis of partial control of the area under mineral exploration concessions. This was necessary to justify operations in an area of difficult access and high operating costs. The results of this now-terminated arrangement are regarded as being of benefit to those directly concerned as well as to the mineral industry in general."

Jan 1, 1966

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the 'coalescence' model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

A brief description of the hydro-gen reduction of nickel from ammoniacal solutions by the Sherritt process is given, indicating how this procedure can now be used to coat a great number of materials -particularly powders -with nickel or cobalt, whereby so-called composite powders are produced. The technique for the production of composite powders is described, particularly with regard to the surface activation of noncatalytic powders, whereby it is possible to coat core powders uniformly with nickel or cobalt. The properties of some of the more interesting composite powders, such as Ni/ AI, Ni/WC, Co/WC, Ni/Graphite and i/P, are discussed as well as possible fields of application for these new products. INTRODUCTION DURING the last decade, no-table advances have been made in pressure hydrometallurgy, so that large quantities of three of the more com1r.on metals, copper, cobalt and nickel are now produced on a commercial scale by hydrometallurgical processes.

Jan 1, 1963

By G. Chahal, L. C. So, S. Faucher, S. Mostaghel, S. -Y. Oh, S. K. Lee

Slag dumping and water granulation are the most commonly used slag treatment methods in the metallurgical industries. In both processes, water is present (by desire for cooling and dispersion or as a result of rain accumulation) and thus equipment and operations are designed to minimize and mitigate the risk of steam explosions resulting from the inappropriate contact of slag with water. Slag handling practices have, therefore, never been inherently safe; even good design, operation, and maintenance are not sufficient to prevent explosions or other related injuries from occurring. For slag handling to become inherently safe, our industry must eliminate the potential contact of water with molten slag. This is today feasible with the advent of dry granulation technologies, a review of which is presented, and it thus falls to us, in the metallurgical sector, to lead the way in their final stages of development and adoption. Furthermore, while slag dumping and water granulation offer some metallurgists the means of valorizing their slag as a by-product, for most, this is not the case. The energy in slag is lost through dumping and water granulation processes, and where slag is sold as a by-product, it is for its chemical content only. Here, dry granulation processes also offer advantages including the production of by-products which hold value in both their chemical content and physical properties and heat recovery. Dry granulation, therefore, augments the methods by which slag may be valorized over traditional processing methods.

Jan 1, 2015

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By Alain Simard, Sylvain Lacroix, Louis-Martin Dubé, Pierre Pilote

"The Harricana-Turgeon belt (HTB) is a poorly known volcano sedimentary belt in the NW part of the Abitibi Sub-province; it includes the Matagami, Joutel, Brouillan and Casa-Berardi mining districts. The HTB is dominated by volcanic rocks, which covers 65% of its surface area, followed by sedimentary (18%) and plutonic (17%) rocks. It is also transected by numerous deformation zones located either at the contacts of volcano-sedimentary units and granitoid bodies or cross-cutting them. A preliminary geological synthesis shows that mineral deposits are associated with certain regional geologic elements.The volcano-sedimentary units are grouped here into twelve band-shaped lithotectonic domains, most of which extend for more than 150 km E-Win the HTB. Each domain is defined by lithologies and facies associations, and gradiometric and electromagnetic signatures.Eight domains are composed of basaltic or basaltic to komatiitic associations, interlayered with thin pelagic sediments, representing sub-marine lava plains. Two domains are composed of basaltic to rhyolitic associations that are interpreted as volcanic arcs formed by one or several central volcanic complexes.The sedimentary rocks are grouped into two lithotectonic domains. Each is composed of rhythmic sequences of turbiditic sandstone- siltstone-shale, Algoma-type banded iron formations and conglomerates bearing plutonic and volcanic pebbles. These three facies come partly from mass flow at the bottom of a slope in a moderately deep marine environment. In each domain, a conglomerate sandstone- siltstone sequence, containing poly genetic pebbles of local provenance, is similar to Timiskaming-type alluvial deposits.The nineteen granitoids, found within the HTB and at its border, belong to numerous petrographic suites, and have been grouped into four structural families: pre-tectonic, pre- to early-tectonic, syn- to late-tectonic, and late- to post- tectonic. The pre- to early-tectonic plutons are presumed to be sub-volcanic and are generaly associated with the volcanism of central complexes.The HTB mineral resources consist essentially of polymetallic (Cu-Zn-Ag-Au) and gold (Au-Ag) deposits. The polymetallic deposits are located exclusively in the two lithotectonic domains composed of basaltic to rhyolitic associations (Matagami-Brouillan and Joutel Raymond). All gold deposits are associated with deformation zones superimposed on lithotectonic domain contacts and highlighted by graphitic units. Most of the deposits are hosted in the Casa-Berardi and Douay deformationzones, located at the contact of the Cartwright basaltic to komatiitic domain and the Taibi sedimentary domain"

Jan 1, 1990

By Jas. E. Thomson

"The Omega mine is in McVittie township in the Larder Lake area, Ontario. Production at the mine commenced in 1936, and, until the end of 1946, ore milled amounted to 1,558,604 tons, from which 207,074 oz. gold and 28,205 oz. silver, valued at $7,585,470, were recovered. The mine workings extend to a depth of 1,975 feet.GEOLOGYThe geology of the mine has been described in detail by C. P. Jenney (l) and the writer (2). The general geology and structure in the vicinity of the mine is discussed on an earlier page in this volume. The rock formations found in the mine workings are indicated on the accompanying plan and section (Figs. 1and2). They consist of an intermingled, south dipping complex of volcanics, sediments, and secondary talc-chlorite schists and carbonates. The carbonatized rocks, which are often referred to as 'dolomite' in the Larder Lake camp, are siliceous-carbonate replacements in the talc-chlorite schist zones. In places they contain green mica, probably fuchsite, and are cut by a stockwork of quartz veinlets and stringers. A stock of syenitic intrusives lies south of the mine workings.STRUCTUREThe main structural features are indicated in Figs. 1 and 2. The formations and orebodies have a pronounced southerly dip, which flattens with depth. The talc-chlorite schist and 'dolomite' zones are part of the Larder Lake fault or 'break' on which there appears to be very large displacement. Evidence throughout the district would indicate that the south side moved up and, in the case of the Omega mine, the thrust may have been distributed throughout the several intensely sheared zones. This slice faulting could account for the repetition of sediments and volcanics. An alternative possibility would be original interbedding of volcanics and sediments."

Jan 1, 1954

By R M. Ennis, J. C. Botham

This paper is one of a series pre-pared to study the role of fuels and reductants in metallurgical processes, especially from the viewpoint of Canadian requirements. The object of these studies is to provide a reason-ably authoritative interpretation on the interrelation of fuels in light of the considerable changes that have taken place in the Canadian energy field during the past few years. Previous papers in this group have dealt with the problem generally, and specifically in terms of the development of the iron and steel industry of Western Canada. These latter papers, presented at the Symposium on Iron and Steel in Western Canada held in Edmonton, Alberta, on September 8-9, 1959, surveyed the ferrous processes of interest for use in Wes tern Canada, especially with regard to solid fuel requirements. At that time it was evident that there was a need for a similar study of the fuels aspect of the non-ferrous metals industry.

Jan 1, 1961

By A. M. Cameron

THE HOISTING PLANT at the Stobie section of the FroodStobie mine is a two-shaft installation designed to handle a daily production of 18,000 tons of ore at depth. The two vertical shafts are within 100 feet of -each other, an arrangement made to provide the needed capacity and to give flexibility of operation (Figure 1). No. 7 shaft, used for handling men and supplies as well as for hoisting ore, has been sunk to the 3000 level and is served by a manhoist handling two cages and an orehoist with two 14-ton capacity Kimberley skips. No. 8 shaft, so far completed to a depth of 1,900 feet, handles only ore. The hoist is semiautomatic with push-button control and the skips are 15-ton capacity bottom-dump. The ore-loading pocket for first stage hoisting at both shafts is 120 feet below 1,600 lev-el and additional pockets are planned, as the shafts are deepened, at 800 foot intervals down to 4,000 feet.

Jan 1, 1956

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By Rodney A. Cooper

The Mary River iron ore deposits were discovered in the 1960?s. The high quality of the deposits was immediately evident, and drilling programs were successful in defining a resource adequate for supporting a feasibility study. Through a combination of ownership, market and political forces, the deposits were not developed. Having missed the window of opportunity, the project remained dormant for over three decades. Baffinland Iron Mines Corporation, with its 100% ownership of the Mary River deposits, began trading publicly in 2004. Modern exploration and metallurgical test work began in 2004 and has continued in 2005 and 2006, resulting in total expenditures during this period of almost C$60 million. In May 2006, an engineering team lead by Aker Kvaerner E&C, a division of Aker Kvaerner Canada Inc., completed a scoping study based on the first of five identified deposits. Highlights of that study include direct shipping of high quality lump ore to Europe over a 34 year mine life at a production rate of 10 million tonnes per annum, based on an indicated resource of 309 million tonnes at 66.1% Fe and an inferred resource of 28 million tonnes at 65.9% Fe. Capital costs were estimated at C$1.5 billion. Using iron ore prices approximately 36% below that of the 2006 market, a pre-tax internal rate of return of 15% was estimated assuming equity financing. Payback on initial capital was 5.9 years. The pre-tax life-of-mine cash flow was estimated to be C$6.3 billion. As a result of this study, Baffinland initiated a Definitive Feasibility Study, under the management of Aker Kvaerner, which is scheduled for completion in December 2007. This paper touches on the geology of the deposits, the current resource and the outlook for expansion. Project permitting, construction planning, logistical challenges and ocean shipping considerations are discussed, providing a current perspective on the project scale, scope and timeline for commercial production. In addition, an overview of the Company?s bulk sampling program will be provided.

May 1, 2007