Search Documents

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By S-E. Vandat

The goal of this work was to select an appropriate electrode for dummy load of diesel engine in fully salt-water in the DESA factory. The electrochemical corrosion rate of general structural steel, commercial pure aluminum and cathode copper calculated as weighting, volumetric and commercial in fully salt-water by city power. After several tests and then applying the fuzzy logic method, it was determined that general structural steel is the best selection for this purpose.

Jan 1, 2005

By J. Aiello

"Introduction Byron Creek Collieries Limited Corbin mine is located in southeastern British Columbia approximately 180 air kilometres southwest of Calgary (Fig. I), twenty four kilometres south of Highway No. 3 via a newly constructed provincial road (Fig. 2). The development of the area began July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J. Roberts first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co., after acquiring 6,000 hectares of land in the area, began to develop a mine. Mr. Roberts was responsible for the construction of the 22-kilometre rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production. The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3) and production from 1908 to 1930 inclusive totalled 2,120,800 tonnes. This production was allocated to the mines as follows:"

Jan 1, 1985

By Alessandro Navarra, Kristian Waters

Mineral concentrators are designed from preliminary geological data, and are therefore subject to geological uncertainty. This uncertainty has a demonstrable impact on the mining lifecycle, and has motivated stochastic strategic mine planning algorithms. The current paper describes how these algorithms may be extended to consider mineral processing operations in conjunction with open-pit mining operations. In particular, the paper describes an effective way to incorporate variable concentrator feed grade into these algorithms, which is the first step toward more elaborate representations of mineral concentrators. The resulting framework will be able to connect geological data to alternate configurations of the downstream resources, hence comparing the benefit of each configuration, and the corresponding capital investments. Sample computations are presented, comparing the NPV and utilization for several different mineral processing capacities.

Jan 1, 2015

By X. T. Feng, Y. H. Hatzor, Y. Tal, G. Yagoda-Biran

"When studying jointed rock mass deformation around underground openings it is of great importance to model correctly the excavation sequence during the numerical simulation. This is because for effective arching mechanism to develop in the roof minute block displacements must take place and some of the available discontinuities shear strength must be mobilized. If from the beginning of the simulation the underground opening already exists in the numerical model, block displacements into the excavation space will initiate and develop from time zero, before the initial stresses in the model have attained their actual initial level in the field. These initial block displacements are therefore artificial and exist only in the numerical model, not in the physical reality, and may lead to erroneous assessment of the stability of the designed structure, typically on the conservative side. We have introduced sequence excavation capabilities both in the numerical manifold (NMM) and the discontinuous deformation analysis (DDA) methods and show here the advantages of this modification using three different case studies, each illuminating a different aspect of this enhancement.We begin with the 25 meter deep 2000 year old underground Zedekiah limestone quarry below the old city of Jerusalem, Israel, which is still standing today unsupported with a free span of 40 m. We show that when the opening exists from the beginning of the numerical simulation the required friction angle for roof stability is 25 degrees, whereas when the opening is removed after all stresses and displacements in the model have been stabilized the required friction angle for stability is only 15 degrees.We then model the excavation sequence of a tunnel model representing a 2500 meter deep research tunnel in the Jinping hydroelectric project, China, in order to determine the in situ stress field at this depth by a grid search inversion of displacement data obtained using the sliding micrometer technology in the course of tunnel excavation. Thus we are able to constrain the in situ stress field at these depths where standard in situ stress measurement procedures are extremely difficult to execute properly.Finally, we use sequence excavation modeling capability to find the total height of the expected loosening zone around tunnels excavated through columnar jointed basalts which pose a great engineering challenge because of the characteristic dense network of slender prismatic blocks that transect the opening at a steep inclination. We use MPBX data obtained during excavation of a deep tunnel through such a rock mass to validate our numerical results and show that application of standard empirical guidelines for dimensioning rock bolt reinforcement in such rock masses may in fact result in very un-conservative design because existing empirical approaches typically ignore the anisotropic nature of the structure of such rock masses which, as we show, plays a very significant role in determination of the extent, shape, and geometry of the loosening zone around the opening."

Jan 1, 2015

By J. Güntner

A significant portion of Outotec's business relates to the application of fluidized bed for processing a wide range of industrial materials, including gold ore and gold concentrate. As part of the former Lurgi and Boliden organization, our division constructed the first industrial reactor for roasting sulphur-bearing materials in 1950, based on the principles of fluidized bed technology. This process, when combined with efficient heat recovery and off-gas treatment and its conversion to sulphuric acid, became the standard for processing sulphur-bearing ores. In the last 60 years we have delivered more than 265 plants and developed (in addition to the standard fluidized bed solution) variants of the fluidization technology, such as the circulating fluidized bed and the bubbling fluidized bed. This paper describes the different options of the fluidized bed technology for gold roasting reflecting on main process design criteria.

Jan 1, 2011

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By J. E. Dutrizac

Mercury balances have been obtained for the flotation circuits at Pamour Porcupine Mines, Timmins, Ontario, and at Brunswick Mining and Smelting Corporation, Bathurst, New Brunswick. The mineral form of mercury in both deposits has been ascertained. At Pamour Porcupine, the mercury is approximately evenly divided among sphalerite, native silverelectrum and tetrahedrite-tennantite; at Brunswick Mining, this element is contained mostly in the sphalerite, although tetrahedrite (and possibly pyrite) also contains minor quantities.

Jan 1, 1979

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By M. M. O?Brien

THE SULLIVAN MINE The Sullivan mine of the Consolidated Mining and ? Smelting Company of Canada, Limited, is situated at Kimberley, B.C., nineteen miles from Cranbrook, a divisional point on the Crowsnest Pass branch of the Canadian Pacific railway. Production started on a small scale in 1900, and in 1914 the mine became the largest lead producer in Canada. In 1925 it was the largest single producer of lead and zinc in the world. Since operations commenced, 4,800,000 tons of ore have been produced from stopes and 170,000 tons from development. At the present time, ore is being mined at the rate of 1,100,000 tons per year, with a yield of about 200,000 lb. lead, 110,000 lb. zinc, and 4,000,000 oz. silver. The town of Kimberley is easily accessible by road as well as by rail. The altitude at Mark creek, a tributary of the St. Mary's river, is 3,700 feet. To th'e north of the creek, Sullivan hill rises to a height of 6,100 feet, and it is on the southern slope of this hill that the mine is located. Sullivan hill is in the Purcell range, which rises between the Rocky Mountain trench on the east and Kootenay lake on the west. It thus lies within what is commonly referred to as the East Kootenay district.

Jan 1, 1926

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By The Staff

THE property of McKenzie Red Lake Gold Mines, Limited, consists of eleven claims located on McKenzie island in Red lake. The mine is about 4,Y:l miles by water from the Howey townsite on the same lake, and about 95 miles north of Kenora, Ont. (see Figure 4). Mail and express are flown-in daily, winter and summer, from Sioux Lookout, Hudson, Kenora, and Winnipeg. All heavy supplies are freighted-in during the summer over a water route, using four marine railway portages, from Hudson, Ont., a distance of about 180 miles. During the winter, freighting over the same route is clone by tractor if necessary, but costs are three to four rimes the summer rate. Due to these conditions, large inventories of supplies must be kept on hand, varying from a spring minimum of $45,000 to a peak of $110,000 early in November. The average cost of all freight brought in from steel during 1937 was $0.01 per pound.

Jan 1, 1938

By G. R. Parslow

U, Fe, Mn, Ni, Cu, Zn and Co data for the sediment in both Key and Seahorse lakes, which overlie portions of known economic uranium deposits in the region, are presented. With the exception of U, Fe and Mn, the elemental distributions can be considered anomalous, in a statistical sense, in both lakes. The U values are of particular interest in that Key Lake is not anomalous, whereas Seahorse Lake is markedly anomalous. Tentative correlations made with background data from other surveys in an attempt to differentiate between anomalous and background values indicate that deviations from linearity in a distribution, and not absolute mean or maximum values, are indicative of anomalous samples within the distribution.

Jan 1, 1979

By K. Ilankoon, I. M. Saman, S. J. Neethling

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behaviour is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. The particle properties such as size, shape and porosity are very important when modelling the liquid holdup and flow within heaps, since the dominant mechanisms at work are quite different. This paper investigates the effect of these particle properties experimentally on heap flow behaviour using a 1-D column leaching system consisting of non-porous glass beads with a system of actual ore particles. The similarities and differences between the two systems on flow behaviour are described using an inter-particle flow model. In addition, the applicability of positron emission particle tracking (PEPT) for laboratory column leaching will be detailed to calculate hydrodynamic dispersion in packed beds compared to more conventional residence time distribution (RTD) tests and also to obtain the time averaged rivulet flow paths through the particles of the bed for the better understanding of heap hydrodynamics.

Jan 1, 2014

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

By Richard Stewart

There are highly competitive world markets in most of the minerals being mined today. The high standard of living we enjoy in North America results in ever increasing productivity through mechanization and automation. Conventional underground and open-pit mining practices throughout the world are constantly changing to reflect the engineering advances of our technology. New records in tunneling, shaft sinking and excavating are being established. Larger and faster equipment is in production. Mining operations are being studied in detail to improve materials, methods and machines. Standards and controls are being established to measure the performance of people and equipment. These steps all tend to improve our present performance. In addition to these short-range improvements, however, there are the basic research and applied research studies which are aimed at developing entirely new approaches to our mining problems. Basic research in rock mechanics is coupled with applied research in rock penetration, fragmentation and stabilization.

Jan 1, 1963

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019